Owners Manual 706.596680 6-Drawer Chest 706.
CRRFTSMRN CHEST TOP AND FACIA PARTS REPLACEMENT Information Center Sears, Roebuck and Co.
CHEST TOP INSTALLATION AND REMOVAL (With task light) Tools Required: 3/8" Wrench Chest Top Removal • Disconnect power from unit. • Remove enough drawers to reach the top back inside of the unit. {See Drawer installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock. Move actuator rod for access. • Remove (4) screws holding top in place. • Lift top off of unit enough to reach the wiring harness. • Disconnect wiring harness from unit. • Remove top from unit.
INFORMATION CENTER INSTALLATION AND REMOVAL Tools Required: Screwdriver, Crosstip Tape Removal • Disconnect power from the unit. • Remove enough drawers to reach the retaining screw under the information center. (See removing and installing drawers.) • Loosen (do not remove) the retaining screw under the information center. • Pull the information center straight out to remove. Note: Tape wire to unit before unplugging the information center. This wiil prevent the wire from retracting into the unit.
FACIA INSTALLATION AND REMOVAL Tools Required: 3/8" Wrench drill 5/32" drill bit Rivet gun Pliers To remove facia • Remove enough drawers to reach the top back inside of the chest. • Remove lock. (See lock installation and removal.) • Remove chest top. See chest top installation and removal. • Carefully drill out (2) rivets holding facia to chest. • Remove facia. Rivet To reinstall facia • Position facia on unit. Make sure connector is on top of chest. • Attach using (2) rivets supplied.
CONNECTING POWER • Ensure that the unit and power cord are clean and dry. • Insert the round end of the power cord connector into the jack in the back of the unit. • Plug the cord into an appropriate electrical outlet. To reinstall, carefully align the slides and push the drawer into the unit until the drawer stops. Fuse block INFORMATION CENTER OPERATION The information center is equipped with a battery backup to maintain memory only.
Temperature Display Pressing ( °f;°c ) toggles inside and outside temperature displays between Celsius and Fahrenheit. • Pressing ( Temp ) toggles inside and outside temperature displays between • ACT (Actual temperature) • MIN (Minimum recorded temperature since last reset) MAX (Maximum recorded temperature since last reset) • Press and hold ( Temp ') for at least two seconds to clear inside and outside minimum and maximum recorded temperatures. • An audible beep will sound when temperature is reset.
CRRFTSMRN DRAWER AND WORK SURFACE PARTS REPLACEMENT Sears, Roebuck and Co.
SLIDE REPLACEMENT Tools Required: Drill 5/32" Drill bit Rivet gun Removal • Remove drawer or work surface from unit. (See drawer and work surface installation and removal.) • Carefully drill out rivet holding slide drawer member to drawer or work surface. • Rotate front of slide drawer member down and out. • Pull slide forward to remove. • Carefully drill out rivet holding slide unit member in place. • Pull slide unit member forward to remove. Installation • Separate slide drawer member from unit member.
DRAWER AND WORK SURFACE REPLACEMENT Tools Required: Drill 5/32" Drill bit Rivet gun Crosstip screwdriver Removal • Remove drawer or work surface from unit. (See Drawer and Work surface installation and removal.) • Carefully drill out rivets holding slides to drawer. • Rotate front of slide down and out. • Pull slide forward to remove. Drawers only • Remove striker. (See striker replacement.) • Remove drawer front. (See drawer front replacement.
DRAWER FRONT INSTALLATION AND REMOVAL Tools Required: Crosstip screwdriver Removal • Remove retaining screw(s). • Slide drawer front assembly as indicated to unhook mounting tabs. • Pull out to remove. Installation • Position drawer front on drawer assembly. • Insert mounting tabs into notches on drawer. • Slide drawer front over to attach. • Install retaining screw(s) to hold drawer front in place.
DRAWER AND WORK SURFACE INSTALLATION AND REMOVAL Note: For pull out work surface without task light, follow drawer removal instructions. DRAWER • Empty the drawer. • Fully extend the drawer. Release Lever Style - Lift or ower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.) Pull out to remove. Tab Style - Depress the release tabs on both sides, (this allows the slides to ride over the stops.) Pull out to remove.
Unplug work surface cord from back of roll-away. Remove and save back retaining clip. Disconnect chain inside back of rollaway. (Move chain toward large round part of slot. Pull out to remove.) Remove the work surface. (See drawer removal instructions.) Retaining Installation • To reinstall, carefully align the slides and push the work surface into the unit until the work surface stops. • Depress release tabs in back corners of the extendable work surface.
CRRFTSMRN BOTTOM REPLACEMENT Tools Required: Socket Wrench 5/16" Socket Removal • Disconnect power from the unit. • Remove contents from drawers. • Carefully lay the chest on its back. Take care to prevent scratches or damage to the unit. • Remove (5) screws holding bottom on unit. • Remove bottom from unit. • Remove counterweight from plastic bottom. Installation • Install counterweight in new plastic bottom. • Position new chest bottom on chest. • Attach using (5) new mounting screws.
CRRFTSMRN TOP, WIRING HARNESS, HARNESS GROMMET Parts Replacement Harness grommet Sears, Roebuck and Co.
WIRING HARNESS REPLACEMENT HARNESS GROMMET REPLACEMENT Tools Required: 3/8" Wrench WIRING HARNESS AND HARNESS GROMMET REMOVAL • Disconnect power from unit. • Remove pull out work surface and enough drawers to reach the top back inside of the unit. (See drawer and work surface installation and removal.) • Remove lock and top from roll-away. (See roll-away top removal and installation.) • Remove harness grommet from rollaway.
TOP INSTALLATION AND REMOVAL Tools Required: Screwdriver, Crosstip Roll-away top removal • Disconnect power from unit. • Remove pull out work surface. (See drawer and work surface installation and removal.) • Remove enough drawers to reach the top back inside of the unit. (See Drawer and Work surface installation and removal.) • Remove lock retaining clip. Pull lock out to remove. • Remove (4) screws holding top in place. • Lift top off of unit enough to reach the wiring harness.
DRAWER AND WORK SURFACE INSTALLATION AND REMOVAL Note: For pull out work surface without task light, follow drawer removal instructions. DRAWER • Empty the drawer. • Fuliy extend the drawer. Release Unplug work surface cord from back of roll-away. Remove and save back retaining clip. Disconnect chain inside back of rollaway. (Move chain toward large round part of slot. Pull out to remove.) Remove the work surface. (See drawer removal instructions.
CRRFTSMRN CHEST TOP WITHOUT TASK LIGHT Tools Required: Screwdriver, Crosstip Chest top removal • Disconnect power from unit. • Remove pull out work surface. (See drawer installation and removal.) • Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.) • Remove lock retaining clip. Pull lock out to remove. • Remove (4) screws holding top in place. • Remove top from unit. Chest top installation • Position top on unit. Attach using (4) screws.
DRAWER INSTALLATION AND REMOVAL Empty the drawer. Fully extend the drawer. Release Lever Style - Lift or ower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.) Pull out to remove. Tab Style - Depress the release tabs on both sides, (this allows the slides to ride over the stops.) Pull out to remove. To reinstall, carefully align the slides and push the drawer into the unit until the drawer stops.
CRRFTSMRN TASK LIGHT REPLACEMENT Tools Required: Screwdriver, Crosstip Removal • Disconnect power from the unit. • Fully extend task light assembly. • Make note of light orientation. • Remove (6) mounting screws to remove light. • Unplug light. Installation • Plug in new light. • Position new light in unit in same orientation as original light. • Fasten new light in place with (6) new mounting screws. • Reconnect power to unit.
CRRFTSMRN LOCKING SYSTEM Parts Replacement Actuator rod Lockbar Sears, Roebuck and Co.
ACTUATOR ROD AND ACTUATOR CHANNEL REPLACEMENT ACTUATOR ROD AND ACTUATOR CHANNEL REMOVAL • Disconnect power from the unit. • Remove work surface (Roll-away only). • Remove pull out work surface (Rollaway only.) See drawer and work surface installation and removal.) • Remove enough drawers to reach the top back inside of the unit. (See drawer and work surface installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock. • Rotate actuator rod straight down.
ACTUATOR ROD BRACKET INSTALLATION AND REMOVAL Removal • Disconnect power from unit. • For roll-aways, remove work surface. (See drawer and work surface installation and removal. • Remove enough drawers to reach the top back inside of the unit. (See Drawer and Work surface installation and removal.) • Remove top from unit. (See top installation and removal for your unit.) • Pull actuator rod bracket forward. Lift out to remove. Installation • Insert actuator rod bracket into hole in back corner of unit.
TOP INSTALLATION AND REMOVAL ROLL-AWAYS, CHESTS WITHOUT TASK LIGHT Tools Required: Screwdriver, Crosstip Removal • Disconnect power from unit. • For roll-aways, remove work surface, (See drawer and work surface installation and removal. • Remove enough drawers to reach the top back inside of the unit. (See Drawer and Work surface installation and removal.) • Remove lock retaining clip. Pull lock out to remove. • Remove (4) screws holding top in place.
CHEST TOP INSTALLATION AND REMOVAL (With task light) Tools Required: 3/8" Wrench Chest Top Removal • Disconnect power from unit. • Remove enough drawers to reach the top back inside of the unit. {See Drawer installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock. Move actuator rod for access. • Remove (4) screws holding top in place. • Lift top off of unit enough to reach the wiring harness. • Disconnect wiring harness from unit. • Remove top from unit.
DRAWER AND WORK SURFACE INSTALLATION AND REMOVAL Note: For pull out work surface without task light, follow drawer removal instructions. DRAWER • Empty the drawer. • Fuliy extend the drawer. Release Unplug work surface cord from back of roll-away. Remove and save back retaining clip. Disconnect chain inside back of rollaway. (Move chain toward large round part of slot. Pull out to remove.) Remove the work surface. (See drawer removal instructions.
CRRFTSMRN LOCK REPLACEMENT Removal • Disconnect power from unit. • For roll-aways, remove work surface. (See drawer and work surface installation and removal • Remove enough drawers to reach the lock retaining clip behind the lock. • Remove lock retaining clip. Pull lock out to remove. Installation • Position lock in unit. Install retaining clip to hold lock in place. • Make sure the back of the actuator rod is inserted into the actuator rod holder in the back of the unit.
DRAWER AND WORK SURFACE INSTALLATION AND REMOVAL Note: For pull out work surface without task light, follow drawer removal instructions. DRAWER • Empty the drawer. • Fuliy extend the drawer. Release Unplug work surface cord from back of roll-away. Remove and save back retaining clip. Disconnect chain inside back of rollaway. (Move chain toward large round part of slot. Pull out to remove.) Remove the work surface. (See drawer removal instructions.
CRRFTSMRN STRIKER REPLACEMENT Tools Required: Screwdriver Removal • Remove drawer from unit. • Turn drawer upside down. • Depress (2) detents. Push striker in to remove. Drawer installation and removal • Empty the drawer. • Fully extend the drawer. Release Depress detents Lever Style - Lift or lower (depending on the slide) the release lever on both sides, {this allows the slides to ride over the stops.) Pull out to remove. Tab Style - Depress the Installation • Turn drawer right side up.
CRRFTSMRN DRAWER FRONT REPLACEMENT Tools Required: Crosstip screwdriver Removal • Remove retaining screw(s). • Slide drawer front assembly as indicated to unhook mounting tabs. • Pull out to remove. Installation • Position drawer front on drawer assembly. • Insert mounting tabs into notches on drawer. • Slide drawer front over to attach. • Install retaining screw(s) to hold drawer front in place. Sears, Roebuck and Co.
