MODEL NO. 536°255861 ® 12.5 HORSEPOWER AL L STEER 40" MOWER 5=SI TRANSAXLE LAWN TRACTO Caution: Read and follow all Safety Rules and Instructions Before Operating This Equipment i illlllll,llllllllll i i ill l i i , = = , ® Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts SEARS, ROEBUCK AND CO.
SAFETY RULES THESE INSTRUCTIONSARE FOR YOUR PROTECTION.PLEASE READTHEM CAREFULLY. IMPORTANT THIS CUTTING MACHINE tS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS+ FAILURE 'TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. L GENERAL e • Know controls and how to stop qutcl_tyo Reed, understand, and foUow all Instructions In the manual and on the machine before starting. Only allow responsible adults, who are familiar with instructions, to operate the machine.
CONGRATULATIONS on your purchase of a Sears Craftsman Tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance Should you experience any problem you cannot easily remedy, please contact your nearest Sears Service CenterlDepartment, We have competent, well-trained technicians and the proper unit.. Please read and retain this enable you to assemble properly_ Always observe HORSE POWER: 12.
TABLE OF CONTENTS ASSEMBLY .............................................. OPERATION .......................................... SERVICE AND ADJUSTMENTS ........... TROUBLE SHOOTING .......................... STORAGE ................................................... REPAIR PARTS ................ ;.................... PARTS ORDERING/SERVICE ..... Back SAFETY RULES ........................................... 2 PRODUCT SPECIFICATIONS ...................... 3 CUSTOMER RESPONSIBILITIES .... 3, 16-22 WARRANTY ..
ACCESSORIES AND ATTACHMENTS These accessories and attachments were available when the unit was purchased. They are also available at most Sears retail outlets, catalog and service centers, Most Sears stores can order these items for you when you provide the model number of your tractor ENGINE CUSTOMER RESPONSIBILITIES SPARK PLUG MUFFLER _lR FILTER GAS CAN ENGINE OIL STABILIZER BLADES BELTS PERFORMANCE Sears offers a wide variety of attachments that fit your vehicle..
Jl_, i i iil,ii i ill ill ii i iii iiiiii illllll Parts packed separately in carton ,IJII II Ill IIIIllllll i i illll Hlll,ll,ll,iH,H,ILI1,1,,/ ,,,,lllllll Illlll 1 © == t1' i ! I 1 ....
ASSEMBL Y TOOLS REQUIRED FOR ASSEMBLY STEERING A socket wrench wifl make assembly easier Standard wrench sizes are listed, (t) Pliers (!) NGPIN Utility knife (1) Screwdriver (Small Phillips with a 1/4 inch shank) (1) Hammer (1) Tire pressure gauge STEERING SHAFT (2) 7/16 inch wrenches (1) 3/8 inch wrench (t) t/2 inch wrench (1) Tape measure When right and left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel), TO REMOVE TRACTOR F
ASSEMBLY HOW TO SET UP YOUR TRACTOR PREPARE BATTERY TO REMOVE BATTERY (See FIG, 3) • Cut Wire tie holding seat plate to seat spring,, For shipping purposes, battery is installed, Remove battery (see TO REMOVE BATTERY instructions below), • Disconnect negative (-) black battery cable using 7t16" wrenchs, • Slide battery boot away from positive(+) battery terminal and disconnect positive (+) red battery cable using 7/t6" wrenchs, e Remove bolt from battery hold-down bracket with a 3t8" wrench, NOTE:
ASSEMBL Y TO ACTIVATE THE BATTERY (See FIG 4) - e Removevent e Fill battery with battery acid. Fitl each celf until it reaches bottom of vent wells.. Do not over flit e Allow battery to stand and settle for at least thirty minutes and then check level of acid.. If acid is below level outlined on electrolyte package, add more acid until correct level is reached.
ASSEMBLY DANGER • Position battery hold-down bracket onto top left edge of battery (opposite terminals). • Reinstall bolt. Tighten bolt to secure battery, • Attach positive (+) red battery cable to positive (+) terminal on battery with a 1/4 X 3/4 inch head screw and a 1/4 inch keps nut, Tighten nut securely, • Place battery boot over positive(+) battery terminal (see Fig, 6 inset). • Attach negative (.
" OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S TRACTOR MANUAL AND SAFETY RULES BEFORE OPERATING YOUR Compare illustrations (see FIG, 7) with your tractorto familiarize yourself with locations of various controlsand adjustments, Save this manual for future reference, ATTACHMENT CLUTCH LEVER MOVE THROTTLE HERE FOR SHIFTCONTROL "rHROTTLE CONTROL LEVER i:ii LEVER cU'rTING HEIGH'r ADJUSTMENT LEVER SW_CH BRAKE,_LUTCH PEDAL SEARS LAWN TRACTORS conform to the safety standards of THE+AMERICAN NA,T_NAL
........... .......................... OPERATION I IIIII I I III IIIII The operation of any tractor can result in foreign objects being thrown into the eyes, which can result in severe eye damage.. Always wear safety glasses or eye shields white operating your tractoror performing any adjustments or repairs.
OPERATION TO MOVE BACKWARD TO OPERATE AND FORWARD The direction of motion (forward - reverse) and ground speed ranges (1-2-3-4-5) are controlled by shift control lever,, e e e MOWER Your tractor is equipped with an operator presence sensing switch, Any attempt by the operator to leave the seat with engine running and attachment clutch lever engaged, wilf shut off engine,, Start tractor with brake-clutch pedat depressed and shift control lever in NEUTRAL position.
OPERATION BEFORE STARTING THE ENGINE TO START ENGINE CHECK ENGINE OIL LEVEL When starting engine for first time or if engine has run out of fuel, it will take extra cranking time to move fuel from tank to engine. Your tractor has two lockoutswitches that connect solenoid to brake-clutch pedal and attachment clutch lever.
OPERATION MOWING TIPS MULCHING e Do not use tire chains when mower housing is attached to unit.. To mulch grass with a mulching mower, you will need to do several thingsdifferentlythan with a conventional mower,. e Run the engine at FAST speed position. o Control forward ground speecl with shift control lever in accordance with type and quantity of grass being mowed.. The more grass to be cut, a slower forward ground speed should be used.
CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS BEFORE EACH USE The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, opera!or must maintain lawn tractor as instructed in this manual. • Check engine oil level • Check brake operation. o • Check tire pressure. Check for loose fasteners.
,CUSTOMER LUBRICATION RESPONSIBILiTiES CHART Orientation view only_ Do Not stand on end.
CUSTOMER RESPONSIBILITIES TRACTOR Always observe maintenance. safety rules when performing any BENT TIP ,EDGE BLADE MOUNTING SCREWS BRAKE OPERATION Your tractor is equipped with an adjustable disc brake, To check brake operation do the following: • Stop tractor on a level surface and place shift control lever in NEUTRAL position, e Depress brake-clutch pedal enough to latch parking brake in tst notch, e Try to push tractor.
CUSTOMER TO SHARPEN RESPONSiBiLITIES BLADE (See FIG. 12A) Care should be taken to keep blade balanced An unbalanced blade wilt cause excessive vibration and eventual damage to mower and engine_ e Blade can be sharpened with a file or on a grinding wheel, Do not attempt to sharpen while on mower.. e Place center hole of brads over head of the nail or end of a screwdriver clamped horizontally in a vice. If blade is balanced, _tshould remain in a horizontal position.
CUSTOMER RESPONSIBILITIES ENGINE OIL RLL CAP/ D1PSTICK LUBRICATION Read ENGINE instructions in this section and OPERATION section of this manual before trying to _tart engine, NOTE: Be sure oil has been added to engine crankcase before trying to start engine, OIL RECOMMENDATIONS Only use high quality detergent oil rated with AP! service classificationSO. Select the oil's SAE viscosity grade according to your expected operating temperature: RECOMMENDEDVISCOSITY i._ , coLoE.
CUSTOMER RESPONSIBILITIES AIR CLEANER (See FIG. 16) WING NUTS Your engine will not run properly and may be damaged by using a dirty air filter,, Clean loam filter after every 25 hours of operation or every season. Service paper cartr!dge every 100 hours or every season, whichever+occurs first. Service air cleaner more often under dusty conditions. COVER TO SERVICE FOAM FILTER + e Remove wing nuts and air cleaner cover.
CUSTOMER RESPONSIBILITIES IN-LINE FUEL FILTER (See FIG, 17A) Fuel filter should be replaced once each season,, tf fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.. Make sure new filter is installedwith the IN marking toward the tank and the OUT rnarking toward the engine. Check fuel system components frequently and replace any parts showing wear or cracks.
SERVICE AND ADJUSTMENTS CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS e Depress brake-clutch pedal and Set parking brake. e Place shift control lever in NEUTRAL position. • Place attachment clutch lever In DISENGAGED position. e Turn ign!tlon key OFF and remove key. ® Make sure the blades and all movtng parts have completely stopped.
SERVICE AND ADJUSTMENTS • Slide deck toward front of tractor_ Pull lower engine pulley belt guide away from engine and slip mower deck drive belt onto _ower engine pulley. Reposition belt guide to 1!16" from pulley.. • Align holes in the mower deck hitch with the front set of holes in the front mounting bracket and reinstall the hitch rod and hairpin cotter, • Place cutting height adjustment lever in lowest position.
SERVICE AND ADJUSTMENTS FRONT-TO-REAR ADJUSTMENT ( See FIG. 23) e e Measure height, from level surface, of right side blade tips at front and rear of mower deck, if distances are equal or not more than 1/8 inch lower in front, no adjustment is necessary° GROOVE_O_ " -ECCENTRIC .,_TT__ MOUNTING • / J! a_=l SCREW FRONT ADJUSTMENT /_ _[..,,_.,,,,.
SERVICE AND ADJUSTMENTS TO ADJUST BLADE DRIVE BELT MOWER DECK BELT GUARD (See FIG. 25) When mower btade drive belt slips and blades will not turn at full speed when mowing, the blade drive belt should be tightened_ • Place attachment clutch lever in DISENGAGED position. o Loosen idler pulley hex nut. o Note position of belt retainer on idler puUey so it can be can be repositioned properly after belt installation.
SER V!CE A ND_A DJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See FIG. 26) MOWER DECK BELT GUARD e Remove mower deck (se_ TO REMOVE DECK Jnthis section., e Remove mower deck belt guard,, e Note position of belt retainer on idler pulley so it can be can be repositioned properly after belt installation, Loosen idler pulley.. e Remove old belt and replace with a new original equipment belt.
SERVICE AND ADJUSTMENTS .............. TO REPLACE TRACTOR (See FIGS. 28 and 29) DRIVE BELT Orientation vlBwonly+ Do Not stand on end+ LOWER ENGINE PULLEY BELT GUIDE Your tractor uses v-belts made o! special compounds_ If any belt becomes worn or breaks, replace with original equipment belt (see REPAIR PARTS section of "this manual). NEVER USE A SUBSTITUTE.
SERVICE AND ADJUSTMENTS TO ADJUST TRACTOR (See FIGS. 31A & 31B) BRAKE Your tractor is equipped with an adjustable mounted on the transa.xleo disc brake TO CHECK BRAKE OPERATIONe Stop tractor on a hard flat surface and turn off engine. • Place shift control lever in NEUTRAL posilion_ e Depress brake-clutch brake in 1st notch. e Try to push tractor,. If you are unable to push tractor, brake is too tight and should be loosened (see TO ADJUST TIGHT BRAKE below)..
SERVICE AND ADJUSTMENTS TO ADJUST SHIFT CONTROL LEVER TO REMOVE WHEEL FOR REPAIRS (See FIG. 33) (See FIGS. 34A and 34B) Adjustment is only required if neutral is not obtained when shift control lever is in neutral sloL e Block up axle securely-. • On front wheels, remove dust cap, retaining ring and washer(s) to remove wheel. • Place shift control lever in NEUTRAL position.. • Release brake clutch pedal, • On rear wheels, remove screws to remove wheel.
+SERVICEAND ADJUSTMENTS TO START ENGINE WITH A WEAK TO REPLACE FUSE (See FIG. 36) BATTERY (See FIG. 35) e Raise hood+ • Locate fuse holder under dash° e Remove fuse and replace with a t5 amp automotive+ type plug in fuse (see REPAIR PARTS section for more information). + CAUTION: Lead-acid batteries generate explosive gases. Keep Sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries+ TO REPLACE HEADLIGHT + BULB (See FIG.
SERVICE AND ADJUSTMENTS TO REMOVE HOOD (See FIGS. 38 and 39) ENGINE • Reach under front of hood and disconnect hood latch spring, TO ADJUST THROTTLE • Raise hood. e Disconnect headlight wire harness • Remove screw used to attach hood lanyard to front of engine+ Hotd hood securely to prevent hood from falling e Remove hairpins and clevis pins used to attach hood to mountingbrackets+ e To reinstall, reverse above procedure. CONTROL CABLE (See FIG.
TROUBLESHOOTING PROBLEM Will not start CORRECTION CAUSE out,;ffuet., 1, Fill fuel tank, Engine not "CHOKED" properly 3,, Engine flooded 4, Bad spark plug 5o Dirty _r filter, 6. Dirty fuel filter. 7. Water in fuel 2, 3,, 4, 5o 6, 7., See TO START ENGINE in Operation section Wait severe} minutes before attempting to start, Replace spark plug Clean/replace air filter, Replace fuel filter Drain fuel tankand carburetor, refill tank with fresh 8, gasoline and replace fuel filter 8. Check all wiring.
TROUBLESHOOTING PROBLEM Unit Will not shift or shifts hard Engine continues to run when operator leaves seat with mower POINTS CQRRECI"ION CAUSE 1. Shifting procedure incorrect 1, Check shifting procedure, Unit MUST come to a 2, Tractor drive belt ahd/er brake out of adjustment 2, 3 Transaxle not operating properly, 3, 1. Faulty operator-safety presence control system 1.
ENGINE FUEL SYSTEM Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more° IMPORTANT: DANGER Never store the engine with fuel indoorsor in a poorly ventilated enclosure, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer, etc_ Handle the gasoline carefui]y_ It is highlyflammable and careless use could result in sedous fire damage to your person andlor property, Drain the fue! into an a
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 CHASSIS & HOOD ASSEMBLY REF: FRONT STEERING PAGE FRONT AXLE ASSY NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 KEY# PART# DESCRIPTION QTY. 1. 2. 3. _ 4_ 5. 6o 7,. 8o 9o 10 1I. t2. 13. t4o 15. 16. 17. 18. 19. 20_ 21.. 22° 23. 24. 25. 26. 27. 28. 29. 30, 31, 32 327076-829 327061-829 180079 120.393 1498 48148 310003 310004 309235 324815-829 57081 1499 324816-829 1"22007 1498 123567 _1282 326297 1499 326296-829 180077 120393 !498 122201 2483 1499 29616 274654 326873-853 326874-853 328154 55273 FRAME, MAIN HITCH, SEARS SCREW, 5/16-t8X1o00 HHC WASHER, FLAT ,344X .
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 KEY# PART# DESCRIPTION OTY° 38. 39_ 40. 4t. 42. 43. 44. 45, 46° 47. 48° 49. 50. 51_ 52. 53. 54. 55. 56. 57. 58, 59° 60. 61.. 62_ 63. 64,. 65, 66° 67,, CONSOLE, MOLDED DASH CONSOLE, REAR COVER SCREW, I/4-20)(30 WAHHATP DASH, W/AMP, W/O CHK SCREW, 1/4_20X.50 PHPNTAP MP SUPPORT, MLD DASH MP SUPPORT, MLD DASH GAS TANK SCREW, 114_20Xo50WAHHTAP BRNG, FL ,7551D,.226 MTNG HOLES NUT, 1/4-20 REGHEXCTRLK BRNG, FL 3601D,.228 MTG HOLES SCREW, 1/4-20 X .
CRAFTSMAN 40" LAWN TRACTOR MODEL 536,255861 HOOD AND CHASSIS ASSEMBLY REF. SEAT CUSTOMER ASSEMBLY VIEW J REF. ...... K_ / NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS. Use of servicelreplacement parts other than original equipment parts may void your warranty.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 KEY# PART# DESCRIPTION QTY. 74 75. 76. 77.. 77A 78_ 79. 80. 8!.. 82. 83_ 84. 85° 86._ 87. 88. 89° 9'0 91, 92, 93. 94.. 95. 96. 97.. 98.. PLATE, SEAT BOLT, 437X156 HHSH 5/16-18 NUT, 5/16-18 REGHEXCTRLK SPRING, SEAT 1.50ODX2.25 LG BLK WASHER, ..281X_63X065 SCREW, I/4-20X.50 WAHHTAP ASSEMBLY, FENDER FENDER CLEVIS SCREW, 5/16-18X56PHPNMA WASHER, .3441DXl .50 DX09 CU NUT, 5/16-18 SQ SCREW, 1t4-20Xo50 WAHHTAP SCREW, 5t16.-18X75 HHC WASHER .375X.88X.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 VIOWER SUSPENSION ASSEMBLY REF_ CHASSIS & HOOD PG. FENDER ASM, REF, CHASSIS & HOOD PG ,," REF_ CHASSIS & HOOD PG_ REF, CUSTOMER ASSY. PO_ REF. / REF, TENSION SPRING t" MOWER FINAL ASSY. PG.1 tt REF_ REF, UPSTOP BOLT NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.
CRAFTSMAN 40" LAWN TRACTOR FRONT STEERING MODEL 536.255861 ASSEMBLY REF. CUSTOMER ASSYoPG. STEER!NGWHEEL & HARDWARE Rd, ROOD PG DASH Ref. KEY =13 REFER TO CHASSIS & HOOD PG, EXTENDED FRAME BRKT,, PAGE NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS.
CRAFTSMAN 40" LAWN TRACTOR KEY# 1. 2. 3, 4 5` 6 7 8. 9. 10. 1t. 12 13 14o 15., 16. 17,, 18 18A 19,, 20,, 21_ 22., 23. 24, 25 26. 27. 28 29. 30. 31, 32, 33. PART# • • • 34. 35. 36. 37. 38, 39, 40 "ORDER MODEL 536.255861 QTY DESCRIPTION * 312280 50546 325585 36625 325586 327619-85,3 454565 329459 21275 FRONT AXLE ASSEMBLY SF AXLE FRONT BEARING FLANGE SP|NDLE,RH RING,RETEX SPINDLEoLH ARM,ASSY, SF 4WS FRT STEER PIN,SPRING TIE ROD ASSEMBLY BALL JOINT 124925 .
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 REAR STEERING ASSEMBLY REFo FRONT STEERING REF_ REAR _) \ .:, NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 KEY# PART# DESCRIPTION QTY, 1 2 3 4 327793 325791 36625 326906 SF ASSY, CAM PLATE SUPPORT ASSY, CAMARM RING, RETEX .57X.05TRU5133-75 WS 4WS DRAG LINK ASM SF PIN, HAIR BEAR!NG, CAM ROLLER SF4WS BOLT, ,625X .
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 MOTION DRIVE ASSEMBLY \ ALL UNNUMBERED ITEMS ARE INTERCHANGEABLE WITH OPPOSITE SIDE NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS, Use of service/replacement parts other than original equipment parts may void your warranty.
CRAFTSMAN KEY# 40" LAWN TRACTOR PART# 'w TRANSAXLE P930-045 5SP4WSSF SCREW, 5/16-18X2 75 HHC GR5 WASHER, FLAT .344X .69X 065 NUT, 5/1'6-18 REGHEXCTRLK PULLEY. 6.60D V4L T/A KEY, WDRF 606.750X. 187X,312 RING, RETEX .58X035TRU5100-62 BELT,V 4L 63,50 BRKT,STABILIZER 920 4360 SF SCREW, 5/16-18X ,75 WAHHTAP WASHER, HVSPTLK .328X,60X ,09 SCREW, 5/16-1BXI.00 HHC WASHER, EXL:K 320X.61XO3 NUT, 5/16-18 REGHEXCTRLK LEVER, SHIFT LOWER SF FENSHIFT CLAMP ,625DIA 27,, 28. 29, 30.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 MOTION DRIVE ASSEMBLY REF. ENGINE PG ENGINE _PG ENGINE DETAIL A i:i!_ FRAME (SEE DETAIL A) FOR ASSEMBLY TO FRAME "_ REFER TO TiRE TREAD PAGE ALL UNNUMBERED ITEMS ARE INTERCHANGEABLE V_TH OPPOSITE SIDE NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS.
CRAFTSMAN KEY# 51. 52,, 53, 54, 55, 56° 57, 58, 59., 60. 61, 62,, 63, 64,, 65. 66_ 67, 68° 69 70_, 71,. 72,, 73 74, 75, 76, 77, 78, 79_ 80, 61, 82° 83° 40" LAWN TRACTOR PART# 329055 45602 329232 319676 302601 56180 302335 321969 41890 4107 45602 1498 56359 39659 35374 327611 57325 1499 43980 50562 323127 2O507 4230 1498. 323222 120393 121222 271184 1498 35410 24167 321915 8'4. 85., 123418 MODEL 536.255861 DESCRIPTION QTY_ BELT GUIDE TEG FAN SEARS WASHER, FLAT .333 X _87 X ..
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 ENGINE & CONTROL ASSEMBLY REF_, CHASSIS & HOOD PG DASH REF. ITEM ENGINE BOLT REF. ITEM ENGINE REF_ CHASSIS & HOOD PG MAIN FRAME REF, MOTll DRIVEPG NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS° Use of serv.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 key# part# description qty, 1 2 v 3 4 5 6 7 8 9 10 11 12 13 !38,, 14 t5 16 v 17 18 19 20 2t 22 23 24 25 26 27 28 29 30 31 32 33 34 327730 50947 44108 180083 138485 54766 328706 173063 46708 56472 35287 327418 120380 i20638 120613 314989 300303 47452 47345 47345 56679 46704 315716 155941 308459 300508 159585 120622 574444 43989 23700 328942 328685 300303 274707 ENGINE 12,5 HP TEC OHVXL SCREW, 318-16X1 25 WAHHTAP NUT, 5/16-18 REGHEXCTRLK SCREW, 5/16-18X1.
CRAFTSMAN PRE-PAINTED 40" LAWN TRACTOR MODEL 536.255861 DECK ASSEMBLY REF.
CRAFTSMAN 40" LAWN TRACTOR KEY# 1 2_ 3 4 5 6 7.. 8+ 9. 10 11 12 13 I4 t57 16 17. !8+ 19 20+ 21+ PART# • • , • • ,+ • 22+ 23, 24+ 25 26 27, 28 29° 30, 31_ 32 33 327453-853 326480 180075 1498 122007 1498 327280-853 122027 1498 317017 180075 1498 325652 180077 120393 1498 325653-853 180077 120393 1498 326893-853 306231 • 34, 35 36 37 38 _' 39 40_ 41 .. . 42 43_ • 44_ 45, 46 47 • 48 49 50 51 52 5-3, 54 55 56 57 55 59 60 61 62 • 63 • 64 65 66 . 67 + 68 69 70 71 72.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.
CRAFTSMAN 40" LAWN TRACTOR KEY# PART# 2, 3, 4, 5,. 6, 7+ 8+ 9. 10. 11 12. 13., 14. 15+ 16 t7. 18. 19 20+ 21_ 22 23 24. 25 26 27 28 29. 30 31 32.. 33 58306 8260 57326 25210 1346 310326 996307 120382 120377 325773 300680 328257 120228 120393 1498 329007 50748 327855 56432 304246 56431 120383 433146 304422 314975 304424 3535 = " = MODEL 536.255861 DESCRIPTION ASSY DECK 40* MOWER DOM ROD, DECKHITCH + PiN, HAIR +091 DlAXl..66LG BOLT, 3/8+16X2.00 CARR WASHER, FLAT .
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 ELECTRICAL ASSEMBLY REF. HOLE IN DASH REF. MOTION DRIVE PGo STABIUZER BRACKET SCREW REF,, KEY #5 REF. Engine Bolt NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS. Use of servicetteplacement parts other than original equipment parts may void your warranty° REF.
CRAFTSMAN KEY# I 2. 3 4 5 6 7 8 9 10 11 12, t3 1415 16. 17. 18. 19. 20, 21. 22. 23 24 25. 26 27, 28, 29 30 31 32, 33 34 35 40" LAWN TRACTOR PART# MODEL 536.255861 DESCRIPTION 329117 41482 303064 52572 57444 41482 327355 321692 327238 327352 327350 328826 315902 57476 57220 326653 53716 187745 t084 1502 271172 271 t87 57444 55511 271184 57547 160505 302257 329715 995346 120854 27t t72 120706 46931 302031 QTY. WIRE HARNESS SF PRESS CLIP, 1 380LG .2551D ASSY,UGHT WIRE_II4 TURN BULB, HEADLAMP "_TIE.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 DECALS O ALL UNNUMBERED ITEMS ARE INTERCHANGABLE WITH OPPOSITE SIDE NOTE: ALWAYS USE ORIGINAL EQUIPMENT PARTS., Use of service/replacement parts other than original equipment parts may void your warranty.
CRAFTSMAN KEY# 1. 2 3. 4. 5 6. 7 8 9. 10 11 12, 13, 14, 15 16. 17. !8. 19,, 20, 21 40;' LAWN TRACTOR PART# 322896 320860 320861 402220 32289B 320870 402212 320862 320863 402213 32O868 311394 321842 320869 402214 322897 322901 402210 402211 402157 MODEL 536.255861 QTY, DESCRIPTION DECAL. V-BELT SCHEMATIC, MOWER DECAL. AWS HOOD RH SF DECAL, AWS HOOD LH SF DECAL.
CRAFTSMAN 40" LAWN TRACTOR MODEL .536.255861 CUSTOMER ASSEMBLY KEY# PART# DESCRIPTION QTY, t_ 2_ 3o 4. 5. 6o 7 8 329054 306654 120393 120368 122007 456378 321837 327350 SEAT, V340 CRAFTSMAN WIRED TRIM WHEEL, STEERING 14" LONG 4WS LT BLK WASHER, FLAT .344 X .69 X 065 WASHER, HVSPTLK 328 X .60 X ..('" SCREW, 5/t6-18 X _75 HHC PIN, SPRING 250 DIA X 2.00 LG KNOB, ROUND 1.50 DIA EXTRA KEY BATTERY ACID PACK 1 1 4 4 ,, " MAY BE PURCHASED LOCALLY.
CRAFTSMAN 40" LAWN TRACTOR MODEL 536.255861 TREAD PATTERNS TIRE SIZE "A" "B" 11 X 4.00 * 5 42295 319679 13 X 5.00 - 6 41060 319680 15 X 6,00 - 6 39830 316702 16 X 6.50 - 8 18 X 8.50 - 8 41081 319683 319682 317400 !8 X 9.50 - 8 20 X 8.00 - 8 41106 319685 316701 319684 58276 319686 55893 53655 319687 319690 20 X 10.00 - 8 20 X 1&O0 - 10 23 X 9°50- 12 "C" "D" 301140 313952 314539 57164 313950 314584 313654 319689 314370 ....
ENGINE MODEL 143.436092 Refo No. 1 2 14 15 16 17 18 19 20 25 26 30 31 35 36 37 38 39 40 40 4o 4t 41 41 42 42 42 4.3 45 46 47 48 5O 5t 52 6O 64 65 66 69 7O 72 75 8O 81 82 83 64 86 88 89 ° 90 91 92 93 100 101 102 103 110 1t9 120 Part No. FOR 40" TRACTOR Ref. No. Part Name 35843 27652 28277 35324 36284 29916 650548 35945 35319 35326 650561 35336B 35327 29826 29918 29216 29642 30322 35776 Cytinder Assyo (IncL Nos° 2 8.
ENGINE MODEL 143.436092 Ref. No. Part No. 290 292 305 307 308 308A 310 314 315 30705 26460 35574 35499 33397 35437 35576 650873 611104 321 322B 323A 325 326 6t 1161 611142 611118 34246 36210 650949 30O63 47 361 FOR 40" TRACTOR PartName Line, Fuel Clamp, Fuel line Tube, Oit filt "0" Ring Clip, Oil fill tube Clip, Oil fill tube Dipstick, Oil Screw, 1/4-20 x 3/4" Coil Assy., Attemoator (3 Amp D.Co, 5 Amp A.Co (Incl. Nos. 321, 322B 323A) Diode Assy.
ENGINE MODEL 143.436092 STARTER MOTOR NO. FOR 40" TRACTOR MODEL 536.255861 35763A Ref.] 15 1'_0. I 18 Part Name 35763[ 1 2 12 3 4 5 6 7 8 9 10 t2 14 19 t5 16 17 18 19 6 Part No.
TRANSAXLE PEERLESS TRANSAXLE REPAIR PARTS MODEL 930-045 FOR 40" TRACTOR MODEL 536,255861 43 6B
PEERLESS Key Noo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 18 2O 21 22 23 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 42A TRANSAXLE Part No.
NOTES 70
NOTES
CRAFTSMAN OWNER'S MANUAL MODEL NO. 536.255861 12.5 HORSEPOWER ALL-WHEEL 40" MOWER DECK ED TRANSAXLE LAWN TRACTOR Eachtractor has itsown model number. Each engine has itsown model number. The Mode! Number for your tractor will be found on the model plate located under the seat.
