Operator's Manual CRAFTSMR 25cc/1.5 cu.in. 2-Cycle 215 MPH/470 CFM GASOLINE POWERED BLOWER/VAC Model No. 358.794772 • • Safety Assembly • • Operation Maintenance • Parts List • Espa_ol, p, 20 i WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun. 1-800-235-5878 Sears, Roebuck 545167641 _.oors,,s,edaro ceo,,o, T,,'_ and Co., Hoffman Rev.
Warranty Statement Identification of Safety Symbols Safety Rules Assembly Operation Maintenance 2 2 3 5 8 11 Storage Troubleshooting Table Emissions Statement Parts List Spanish Parts and Ordering 13 14 15 17 20 Sack Cover TWO YEAR FULL WARRANTY ON CRAFTSMAN@ GAS BLOWER When used and maintained according to the operator's manual, if this product fails due to a defect in material or workmanship within two (2) years from the date of purchase, return it to any Sears store, Sears Service Center, or other Cr
_O Do not wear jewelry, loose clothing, or clothing with loosing hanging straps, etc. Theylength, can Secure ties, hair tassels, above shoulder be caught in moving parts. _ _ WARNING: Stop the engine before opening the vacuum inlet door. The engine must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades.
Use your unit as a blower for: • Sweeping debris or grass clippings from driveways, sidewalks, patios, etc. • Blowing grass clippings, straw, or leaves into piles, around joints, or between bricks. Use your unit as a vacuum for: • Picking up dry material such as leaves, grass, small twigs, and bits of paper. • For best results during vacuum use, operate your unit at high speed. • Move slowly back and forth over the material as you vacuum.
blower tubes. When using the optional vacuum kit, always install vacuum tubes and vacuum bag assembly. Make sure vacuum bag assembly is completely zipped. • Check air intake opening, blower tubes, and vacuum tubes frequently. always with engine stopped and spark plug disconnected. Keep vents and discharge tubes free of debris which can accumulate and restrict proper air flow. • Never place any object in air intake opening as this could restrict proper air flow and cause damage to the unit.
WARNING: If you receive your unit assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure. A standard screwdriver is required for assembly. BLOWER ASSEMBLY BLOWER TUBE ASSEMBLY If you have already assembled your unit for use as a vacuum, remove the vacuum tubes and collection bag. 1. Align the rib on the upper blower tube with the groove in the blower outlet; slide the tube into place.
6. Turnknob clockwise tosecure elbowtube. VACUUM TUBE ASSEMBLY _WARNING:Stopengine andbe suretheimpeller blades have stopped turning before opening thevacuum inlet doororattempting toinsert orremove thevacuum orblower tubes. Therotatingblades cancause serious injury. 1. Insert thetipofascrewdriver into the latch area of the vacuum LatchA_ea q Blower Vacuum 2. 3. Push the upper vacuum tube into the vacuum inlet. Tum the tube counterclockwise until a click is felt to secure the tube to the blower unit.
SHOULDER STRAP ATTACHMENT (optional acce88ory #71-85783) 1. Pass the shoulder strap over your head and onto your left shoulder. 2. Snap the hook onto the retainer (see following illustration). BLOWER USE VACUUM USE Retainer KNOW YOUR BLOWER READ THiS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT Compare the illustrations with your unit to familiarize yourself with the location of the vadous controls and adjustments. Save this manual for _ture reference.
THROTTLE POSITION LEVER The THROTTLE POSITION LEVER is designed to allow setting engine speed during blower use only. To avoid causing damage to the unit, DO NOT attempt to use the throttle position lever during vacuum use. PRIMER BULB The PRIMER BULB removes air from the carburetor and fuel lines and flits START LEVER The START LEVER helps to supply fuel to the engine to aid in starting. Activate the starting system by moving the start lever to the START position.
leaded gasoline. Included with this blower is a 3.2 ounce container of oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to f_el before fueling your unit.
Starter Handle 6. \ Start/_ Lever Primer / Bulb 4. 5. This unit has the Sim-pul' starting system. You do not have to pull the starter rope handle sharply or briskly. Pult starter rope handle 5 times with a controlled and steady motion (no more than 3 times above 90F). If engine starts and runs prior to 5 pulls, allow engine to run for 5 seconds; then, fully squeeze the throttle trigger to disengage the starting system (start lever returns to RUN position). Steps 5 and 6 are not necessary.
CHECK FOR LOOSE FASTENERS AND PARTS • Muffler • Spark Plug Boot • Air Filter • Housing Screws CHECK FOR DAMAGED OR WORN PARTS Contact Sears Service Center for replacement of damaged or worn parts. • Fuel Tank - Do not use unit if fuel tank shows signs of damage or leaks. • Vacuum Bag - Do not use vacuum bag if it is torn or damaged. INSPECT AND CLEAN UNIT AND LABELS • After each use, inspect complete unit for loose or damaged parts. Clean the unit using a damp cloth with a mild detergent.
, Spark Arresting Screen Screws Replace the spark arresting screen every 50 hours of operation or if any damage or breaks in file screen are noted. NOTE: Do not attempt to clean the spark arresting screen. 1. Remove 3 screws from muffler cover. Remove muffler cover. 2. Loosen and remove 4 screws from the muffler hood. Remove the muffler hood and spark arresting screen. 4. Install new spark arresting screen. 5. Reinstall muffter hood and 4 screws. Tighten screws securely. 6.
ENGINE • Remove spark plug and pour 1 teaspoon of 40:1,2-cycle engine oit (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil. • Replace spark plug with new one of recommended type and heat range. • Clean air filter. TROUBLESHOOTING • Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts. • At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.
YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U.S. Environmental Protection Agency/California Air Resources Board and Sears, Roebuck and Co., U.S.A., are pleased to explain tile emissions control system warranty on your year 2007 and later small off-road engine. In California, all small off-road engines must be designed, built, and equipped to meet the State's stringent anti-smog standards.
WHERE TO GET WARRANTY SERVICE: Warranty services or repairs shall be provided at all Sears Service Centers. Call 1-800-469-4663. MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION RELATED PARTS: Any Sears approved replacement part used in the performance of any warranty maintenance or repair on emission related parts will be provided without charge to the owner if the part is under warranty.
REPAIR PARTS SEARS GAS BLOWER MODEL 358.794772 2_ _&WARNING A_ repair8 mahltenanee adjustments and ilot descdbed in the Operatol's Manual must _e performed by Qualified Selvice Re 5onne_ Ref 1 2. 3 4 5 6 7 6. 9 10 11 12. 13 14 15 16 17 18. 19. 20 21 22. 23 24 25 26 27 28. 29. 30 31 32. 33 34 35 Part No.
REPAIR PARTS SEARS GAS BLOWER MODEL 358.794772 / ,t_WARNING AI_ lepairs adjustment3 and maintenance not desodbe_l in the Ope_ato's Manua_ must be performer1 by Qualified Se vice Personnel Ref. Part No.
REPAIR PARTS SEARS GAS BLOWER MODEL 358.794772 / _ i \"C ......... i 7 Ref. Part No Description 1 2.