Operator’s Manual 4-Cycle WEEDWACKER® GAS TRIMMER Model No. 316.791990 • SAFETY • ASSEMBLY • OPERATION • MAINTENANCE • PARTS LIST • ESPAÑOL, P. 15 CAUTION: Before using this product, read this manual and follow all safety rules and operating instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visit our website: www.sears.
RULES FOR SAFE OPERATION CALIFORNIA PROPOSITION 65 WARNING The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
RULES FOR SAFE OPERATION • Wear heavy, long pants, boots and gloves. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level. • The cutting attachment shield must always be in place while operating the unit. Do not operate unit without both trimming lines extended, and the proper line installed. Do not extend the trimming line beyond the length of the shield. • This unit has a clutch. The cutting attachment remains stationary when the engine is idling.
WARRANTY STATEMENT CRAFTSMAN PROFESSIONAL FULL WARRANTY If this Craftsman Professional product fails due to a defect in material or workmanship within three years from the date of purchase, return it to any Sears store, Parts and Repair Service Center, or other Craftsman outlet in the United States for free repair (or replacement if repair proves impossible). This warranty applies for only one year if this product is ever used for commercial or rental purposes.
ASSEMBLY INSTRUCTIONS Adjust by lifting slightly on the rear of the lower clip, push or pull the loose end of the strap length to fit the operator’s size and comfort. (Fig. 3). 3. Attach the shoulder clip to the unit. (Fig. 4) INSTALL THE CUTTING HEAD SHIELD 1. Place the cutting head shield onto the guard mount bracket, making sure to align the holes on the shield with the ones in the guard mount bracket. (Fig. 5) 2. Take the 4 shield screws and screw each one into the shield until finger tight. 3.
OIL & FUEL INFORMATION STARTING/STOPPING INSTRUCTIONS Choke Lever Fully press and Primer Bulb release the primer bulb 10 times, slowly. Some amount of fuel should be visible in the primer bulb and fuel lines (Fig. 11). If you can’t see fuel in the bulb, press and release the bulb as many times as it Fig. 11 takes before you can see fuel in it. Starting Position 4. Place the choke lever in Position 1 (Fig. 11). 5. Crouch in the starting position (Fig. 12).
OPERATING INSTRUCTIONS MAINTENANCE & REPAIR INSTRUCTIONS TIPS FOR BEST TRIMMING RESULTS • For best trimming results, operate unit at full throttle. • Keep the cutting attachment parallel to the ground. • Do not force the cutting attachment. Allow the tip of the line to do the cutting, especially along walls. Cutting with more than the tip will reduce cutting efficiency and may overload the engine.
MAINTENANCE & REPAIR INSTRUCTIONS CHECKING THE OIL LEVEL 1. Open the air filter cover by Air Filter Cover unscrewing the air filter screw (Fig. 22). 2. Remove the air filter (Fig. 25). Air Filter 3. Wash the filter in detergent Screw and water (Fig. 24). Rinse the filter thoroughly and allow it to dry. 4. Replace the air filter into Fig. 22 the base plate (Fig. 25). Air Filter Cover NOTE: If the unit is operated without the air filter, Back Plate you will VOID the warranty. 5.
MAINTENANCE & REPAIR INSTRUCTIONS Exhaust Rocker Arm If the clearance is not Adjusting within specification: Feeler Nut Gauge a. Turn the adjusting nut using a 5/16 inch (8 mm) wrench or nut driver (Fig. 31). 0.003–0.006 in. (0.076–0.152 mm) • To increase clearance, turn the adjusting nut counterclockwise. Valve Stem • To decrease clearance, Fig. 31 turn the adjusting nut clockwise. b. Recheck both clearances, and adjust as necessary. 9. Reinstall the rocker arm cover using a new gasket.
MAINTENANCE & REPAIR INSTRUCTIONS CLEANING 2. Start the engine and allow it to run until it stalls. This ensures that all gasoline has been drained from the carburetor. 3. Allow the engine to cool. Remove the spark plug and put 5 drops of high quality motor oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug. NOTE: Remove the spark plug and drain all of the oil from the cylinder before attempting to start the trimmer after storage. 4.
MANAGE MY HOME INFORMATION NEED MORE HELP? You’ll find the answer and more on managemyhome.com – for free! I I I I Find this and all your other product manuals online. Get answers from our team of home experts. Get a personalized maintenance plan for your home. Find information and tools to help with home projects. brought to you by Sears SPECIFICATIONS ENGINE* Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REPAIR PROTECTION AGREEMENTS Congratulations on making a smart purchase. Your new Craftsman® Professional product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That’s when having a Repair Protection Agreement can save you money and aggravation.
CALIFORNIA EVAPORATIVE EMISSION CONTROL WARRANTY STATEMENT Your Warranty Rights and Obligations The California Air Resources Board and Sears, Roebuck and Co. ( Sears) is pleased to explain the evaporative emission control system’s warranty on your 2007 model year and later small off-road (equipment type) engine.
NOTES 14
Manual del Operador 4 Ciclos WEEDWACKER® RECORTADOR de GASOLINA Modélo No. 316.791990 • SEGURIDAD • MONTAJE • FUNCIONAMIENTO • MANTENIMIENTO • LISTADO DE PIEZAS PRECAUCION: Lea el manual del operador y siga todas las advertencias e instrucciones de seguridad. Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visite nuestro sitio web: www.sears.
NORMAS PARA UNA OPERACION SEGURA Toda la información, las ilustraciones y las especificaciones contenidas en este manual se basan en la información más reciente disponible en el momento de impresión del manual. Nos reservamos el derecho de hacer cambios en cualquier momento sin aviso previo. PROPOSICIÓN 65 DE CALIFORNIA ADVERTENCIA Los símbolos de seguridad se utilizan para llamar su atención sobre posibles peligros. Los símbolos de seguridad y sus explicaciones merecen toda su atención y comprensión.
NORMAS PARA UNA OPERACION SEGURA • Use pantalones largos y gruesos, botas, guantes y camisa de manga larga. No use ropa holgada, alhajas, pantalones cortos, sandalias ni esté descalzo. Sostenga el cabello sobre el nivel de los hombros. • La protección accesoria de corte debe estar siempre colocada en su lugar mientras opere la unidad. No opere la unidad con las dos líneas de corte extendidas, y la línea correcta instalada. No extienda la línea de corte más allá de la longitud de la protección.
GARANTÍA GARANTÍA TOTAL PROFESIONAL DE CRAFTSMAN Si este producto de Craftsman Professional falla debido a un defecto en el material o en la mano de obra dentro de un período de tres años a partir de la fecha de compra, devuélvalo a cualquier tienda o Centro de Servicio de Piezas y Reparaciones Sears u otro establecimiento de Craftsman en los Estados Unidos para que sea reparado sin costo alguno (o ser reemplazado si resulta imposible repararlo).
INSTRUCCIONES DE ENSAMBLE INSTALE LA CORREA DE LOS HOMBROS 1. Póngase el arnés bien utilizando la presilla o sobre la cabeza y sobre el hombro. (Fig. 2). 2. Ajústela levantándola ligeramente en la parte posterior de la presilla inferior, empuje o tire del extremo suelto de la correa para adaptarla al tamaño y comodidad del operador. (Fig. 3). 3. Fije la presilla de los hombros a la unidad. (Fig. 4) INSTALACIÓN DEL PROTECTOR DEL CABEZAL DE CORTE 1.
INFORMACION DEL ACEITE Y DEL COMBUSTIBLE INSTRUCCIONES DE ARRANQUE Y APAGADO CARGA DE COMBUSTIBLE EN LA UNIDAD 9. Mantenga oprimido el Posición de regulador y deje que Arranque el motor se caliente durante 15 a 30 segundos. 10. Coloque la palanca del obturador en Posición 3 (Fig. 11) la unidad está lista para Control del usarse. regulador SI... El motor no arranca, Fig. 12 regrese al paso 4. Si...
INSTRUCCIONES DE OPERACION INSTRUCCIONES DE MANTENIMIENTO Y REPARACION • El tipo de vegetación que corte • El lugar donde se corta Por ejemplo, la línea se desgastará más rápido cuando corte contra un muro que cuando corte alrededor de un árbol. RECORTE DECORATIVO El recorte decorativo se realiza eliminando toda la vegetación de alrededor de los árboles, postes, cercos, etc. Gire toda la unidad a modo de que el accesorio de corte se ubique a un ángulo de 30° con el suelo (Fig 14). 1.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION 5. Compruebe el nivel de Tapón de aceite aceite. El aceite debe Anillo quedar exactamente en la parte inferior de las roscas en O del orificio de llenado de aceite. (Fig. 19) 6. Si el nivel está bajo, agregue una pequeña cantidad de aceite en el orificio de llenado de aceite y vuelva a Fig. 18 medir (Fig. 19).
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION 2. Suelte el gatillo del regulador y deje que el motor funcione en mínima. Si el motor se para, inserte un destornillador Phillips pequeño en el orificio de la cubierta del motor (Fig. 26). Gire el tornillo de mínima hacia adentro, en sentido horario, de a 1/8 de vuelta por vez (según sea necesario) hasta que el motor funcione en mínima suavemente. NOTA: El accesorio de corte no debe girar cuando el motor está funcionando en mínima. 3.
INSTRUCCIONES DE MANTENIMIENTO Y REPARACION MANTENIMIENTO DEL AMORTIGUADOR DE CHISPAS 1. Saque la cubierta del amortiguador de chispas. Lea Huelgo del brazo oscilante. Spark Arrestor Muffler Screen 2. Con un destornillador de vástago plano o broca Diverter Torx T20, saque el tornillo T-25 que conecta la cubierta Screw del amortiguador de chispas al silenciador (Fig. 33). Slot 3. Saque la orejeta de la T-20 Screw cubierta del amortiguador Fig. 33 de chispas fuera del silenciador.
RESOLUCION DE PROBLEMAS CAUSA EL MOTOR NO ARRANCA ACCIÓN El tanque de combustible está vacío Llene el tanque con combustible bien mezclado La bombilla de cebado no fue oprimida lo suficiente Oprima la bombilla de cebado total de 10 veces El motor está inundado Use el procedimiento de arranque El combustible es viejo o está mal mezclado Drene el tanque de gasolina / Agregue mezcla de combustible nueva La bujía de encendido está arruinada Cambie o limpie la bujía de encendido Parachispas obstruido
ESPECIFICACIONES MOTOR* Tipo de motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enfriado por aire, 4 ciclos Desplazamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 cc (1,6 pulgadas cúbicas) R.P.M. de operación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DECLARACIÓN DE GARANTÍA DE CONTROL DE EMISIONES EVAPORATIVAS DE LA EPA PARA CALIFORNIA Los Derechos y Obligaciones de Usted según la Garantía El Consejo de Recursos del Aire (Air Resources Board) de California, la Agencia de Protección del Medio Ambiente (EPA) y Sears, Roebuck and Co. (Sears) tienen el placer de explicar la garantía del sistema de control de emisiones en su motor “off-road” pequeño modelo del año 2008 y posterior.
Responsabilidades del Propietario según la Garantía Como propietario del motor “off-road” Lawn & Garden pequeño, usted es responsable de realizar el mantenimiento requerido que se indica en su manual de propietario. Sears recomienda que usted conserve todos los recibos que cubren el mantenimiento de su Motor Lawn & Garden, pero Sears no puede denegar la garantía solamente porque usted no tenga los recibos.
NOTES 29
PARTS LIST REPLACEMENT PARTS - MODEL 316.791990 4-CYCLE GAS TRIMMER 23 5 13 24 25 14 1 2 3 15 6 1 4 7 5 26 7 35 8 9 13 13 10 11 12 16 28 18 17 31 30 19 29 32 21 20 27 22 34 13 33 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 753-05843 753-05802 753-05253 791-181751 753-05845 753-05803 791-181003 753-05804 753-05248 753-05673 753-05255 753-05266 753-05805 753-05671 753-05672 753-05681 753-05377 Description Item Part No.
PARTS LIST REPLACEMENT PARTS - MODEL 316.791990 4-CYCLE GAS TRIMMER 5 4 1 10 2 1 3 6 9 7 8 8 14 Item Part No.
Get it fixed, at your home or ours! Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accesspries and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.