OPERATOR'S MANUAL II:RRFTSMRN°I 3/8 in., 18 VOLT DRILL-DRIVER VARIABLE SPEED/REVERSIBLE Model No. 315.115370 _, WARNING: To reduce the risk of injury, the user must read and understand the operator's product. Customer manual before using this Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Heffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.
• Warranty .......................................................................................................................................................................... • 2 Introduction ................................................................................................................................................... :................. 2 • General Safety Rules ......................................................................................................................
_, WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS WORK AREA • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
SERVICE • Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualifiedpersonnelmay resultin a risk of injury. • When servicing a tool, use only identical replacement parts, Follow instructions in the Maintenance section of this manual, Use of unauthorizedparts or failureto follow Maintenance Instructions may create a risk of shock or injury.
_1=WARNING! could result in a risk of fire and electric shock. If extension cord must be used, make sure: READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger.
Someofthefollowing symbols maybeusedonthistool.Please studythemandlearntheirmeaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
Thefollowing signalwordsandmeanings areintended toexplain thelevelsofriskassociated withthis product. SYMBOL SIGNAL MEANING ,_ DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. ,_ WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
PRODUCT SPECIFICATIONS Chuck .......................................................... 3/8 in. Keyless Motor .................................................................. 18 Volt DC Clutch ................................................................ 24 Position Switch .......................................................... VariableSpeed Charger Input ................................... 120 V, 60 Hz, AC only No Load Speed ................................................. 0-650/min.
KNOW YOUR DRILL-DRIVER LED WORKLIGHT See Figure 1. The LED worklight, located on the front of the tool base, illuminates when the switch trigger is depressed. This provides extra light for increased visibility. Beforeattemptingto use this product,familiarize yourself with all operating features and safety rules, BIT STORAGE LEVEL Bits provided with the drill-driver can be placed in the storage area, located on the base of the drill.
_, WARNING: Press down on battery pack to be sure contacts on battery pack engage properly with contacts in charging stand. Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. The charge indicator light (LED), located on the charging stand, will light up red and glow when the charger is properly connected to power supply. This light indicatesthe charger is operating properly.
BATTERY PACK SHOWNIN CHARGER \ TO REMOVE BATTERY PACK See Figure3. CHARGING ASSEMBLY • Lockthe switch triggeron the drillby placing the direction of rotation selector in the center position. • Locatethe latches on the side of the battery pack and depress to release the battery pack from the drill. • Removethe battery pack from the drill. REDLED ORANGE LED CHARGING STAND Fig. 2 TO INSTALL BATTERY PACK See Figure 3.
Avoid running the drill at low speeds for extended periods of time. Running at low speeds under constant usage may cause the drill to become overheated. If this occurs, cool the drill by running it without a load and at full speed. WARNING: Battery tools are always in operating condition. Therefore, the switch should always be locked when not in use or carrying at your side. SWITCH TRIGGER See Figure 4. KEYLESS CHUCK To turn the drill ON, depress the switch trigger.
ADJUSTABLE TORQUE CLUTCH LED WORKLIGHT See Figure 7. The drillis equipped with an adjustable torque clutch for driving different types of screws into different materials. The proper setting depends on the type of material and the size of screw you are using. The LED worklight on the foot of the drill will come on when the switch trigger is depressed. This provides additional lighting on the surface of the workpiece for operation in lower-light areas. ADJUSTING TORQUE See Figure 6.
INSTALLING BITS See Figure 9. _, • Lock the switchtrigger by placingthe direction of rotation selectorin the center position, • Open or closethe chuck jaws to a pointwhere the opening is slightlylargerthan the bit size you intend to use. Also, raisethe front of the drillslightlyto keep the bit from fallingout of the chuck jaws. WARNING: Make sure to insert the drill bit straight into the chuck jaws. Do not insert the drill bit into the chuck jaws at an angle then tighten, as shown in figure 10.
_t, LEVEL WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. DRILLING See Figure 11. A level is located on top of the motor housing to help keep the drill bit level during use. • Check the direction of rotation selector for the correct setting (forward or reverse).
_, Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. A CHUCK REMOVAL See Figures 12 - 14. WARNING: When servicing, use only identical The chuck may be removed and replaced by a new one. WARNING: Always wear safety goggles or safety glasses with side shields when using compressed air to clean tools. If the operation is dusty, also wear a dust mask. • Lock the switch trigger by placing the direction of rotation selector in center position.
• Insert the hex key into the chuck and tighten the chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction, This will loosen the chuck on the spindle. It can now be unscrewed by hand. MALLET BATTERIES The battery pack for this tool is equipped with nickel-cadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this tool have been designed to provide maximum trouble-free life.
-- L,rtAr IbMAN z_ VULI UHILL-UHIVPH- MUUbL NUMUI:H dlb,11_);.t/u -- number in all correspondence regarding your DRILL-DRIVER or when ordering repair parts. the model The model number will be found on a plate attached to the motor housing. Always mention I SEE BACK PAGE FOR PARTS ORDERING ] INSTRUCTIONS 2 1 \ 5 \ PARTS LIST Key NO, PaN Number 1 2 3 4 5 6 6612OO1 6903326 940237075 140295004 130260001 300912194 983000638 Description Qty. Chuck Screw ....................................
Get t fixed,at Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it{ For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-800469-4663) Call anytime, day or night (U.S.A. and Canada) ::; '_ www.sears.