Owner’s Manual/Manual Del Propietario ® 1/2 HP GARAGE DOOR OPENER ABRIDOR DE PUERTA DE COCHERA For Residential Use Only/Sólo para uso residencial Model/Modelo 139.5399211 ENGLISH ESPAÑOL Read and follow all safety rules and operating instructions before first use of this product. Leer y seguir todas las reglas de seguridad y las instrucciones de operación antes de usar este producto por primera vez. Fasten the manual near the garage door after installation.
TABLE OF CONTENTS Introduction 2-7 Adjustment Section Safety symbol and signal word review........................2 Preparing your garage door ........................................3 Tools needed ...............................................................3 Planning ..................................................................4-5 Carton inventory ..........................................................6 Hardware inventory .....................................................
Preparing your garage door WARNING Before you begin: • Disable locks. • Remove any ropes connected to garage door. • Complete the following test to make sure your garage door is balanced and is not sticking or binding: 1. Lift the door about halfway as shown. Release the door. If balanced, it should stay in place, supported entirely by its springs. 2. Raise and lower the door to see if there is any binding or sticking.
Planning Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener. Depending on your requirements, there are several installation steps which may call for materials or hardware not included in the carton.
Planning (Continued) WARNING ONE-PIECE DOOR INSTALLATIONS • Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 12. • Depending on your door’s construction, you may need additional mounting hardware for the door bracket (Step 12). Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
Carton Inventory Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. KEEP THE FOAM INTACT (see page 10). Hardware for assembly and installation is shown on the next page. Save the carton and packing material until installation and adjustment is complete.
Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures.
WARNING CAUTION ASSEMBLY STEP 1 Assemble the Rail To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the rail. To avoid installation difficulties, do not run the garage door opener until instructed to do so. 1. Turn the opened rail carton upside down and empty its contents onto a level work surface. 2. Unfold the rails, taking care to avoid kinking the screw rod joints. 3.
Assemble the Rail (Continued) 4. Beginning with the sprocket end, straighten the three rail sections so that the screw rod is in a straight line at the joints. (Avoid handling the joints, which may have sharp edges.) 5. Carefully slide the pins at the top edge of the rail into the openings on the adjacent rail. It is essential that the rail assembly be on a level surface to achieve proper alignment and to avoid damage to the pins. 6.
ASSEMBLY STEP 2 Fasten the Rail To the Motor Unit and Install the Trolley NOTE: To aid in assembly and installation, replace the foam packing around the motor unit. Remove it after Installation Step 4. • Working on a level surface, align the rail assembly with the motor unit, as shown. • Slip the coupling over the rail sprocket. • Slide the rail through the motor unit bracket until the coupling fits securely over the motor unit sprocket.
Lock Nuts 1/4"-20 ASSEMBLY STEP 3 Rail Brackets Attach the Rail Brackets • Align rail brackets to end of rail assembly, as shown. • Insert two 1/4"-20 x 5/8" hex bolts and lock nuts. Tighten securely with a 7/16" socket. Hex Bolts 1/4"-20x5/8 You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section.
Unfinished Ceiling INSTALLATION STEP 1 OPTIONAL CEILING MOUNT FOR HEADER BRACKET Determine the Header Bracket Location 2x4 Header Wall WARNING Vertical Centerline of Garage Door To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. • Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry.
INSTALLATION STEP 2 Install the Header Bracket Wall Mounting Holes You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). CEILING MOUNT ONLY The nail hole is for positioning only. You must use lag screws to mount the header bracket.
INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring. • Position the rail bracket against the header bracket. • Align the bracket holes and join with a clevis pin 5/16"x2-3/4" as shown. • Insert a ring fastener to secure.
WARNING INSTALLATION STEP 4 Install The Protector System ® • Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. • To prevent SERIOUS INJURY or DEATH from a closing garage door: – Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be disabled. – Install the safety reversing sensor so beam is NO HIGHER than 6" (15 cm) above garage floor.
INSTALLING THE BRACKETS Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. They may be installed in one of three ways, as follows. Figure 1 DOOR TRACK MOUNT (RIGHT SIDE) Door Track Garage door track installation (preferred): • Slip the curved arms over the rounded edge of each door track, with the curved arms facing the door.
MOUNTING AND WIRING THE SAFETY SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (see Figure 5). • Finger tighten the wing nuts. Figure 5 Wing Nut Carriage Bolt 1/4"-20x1/2" Recommended Wire Routing 1. Using insulated staples, run the wires from both sensors to the rail at the door header (see Figure 6). 2.
WARNING CAUTION INSTALLATION STEP 5 Position the Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough.
WARNING INSTALLATION STEP 6 Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing any brackets into masonry. CAUTION Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before installing the opener.
WARNING WARNING INSTALLATION CAUTION STEP 7 WARNING Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONLY to 24 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage door: • Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.52 m), and away from all moving parts of door.
INSTALLATION WARNING STEP 8 WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: • Be sure power is not connected to the opener, and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection. • Garage door installation and wiring MUST be in compliance with all local electrical and building codes. • NEVER use an extension cord, 2-wire adapter, or change plug in any way to make it fit outlet. Be sure the opener is grounded.
WARNING CAUTION INSTALLATION STEP 10 Install the Lights and Lens To prevent possible OVERHEATING of the endpanel or light socket, • DO NOT use short neck or specialty light bulbs. • DO NOT use halogen bulbs. Use ONLY incandescent. • Install a 100 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF. • Insert bottom lens tabs into slots on chassis.
WARNING CAUTION INSTALLATION STEP 12 Fasten the Door Bracket Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two vertical supports. A vertical reinforcement brace should cover the height of the top panel.
ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes. • Drill 5/16" pilot holes and fasten the bracket with hardware supplied.
INSTALLATION STEP 13 Inner Trolley Connect Door Arm to Trolley Outer Trolley Follow instructions which apply to your door type as illustrated below and on the following page. Ring Fastener SECTIONAL DOORS ONLY • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 2" (5 cm) as shown in Figures 1, 2 and 3.
ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener. 2. Adjustment procedures, Figure 5: • On one-piece doors, before connecting the door arm to the trolley, the travel limits must be adjusted.
WARNING ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, the safety reversal system MUST be tested.
WARNING ADJUSTMENT STEP 2 Adjust the Force Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Too much force on garage door will interfere with proper operation of safety reversal system. • NEVER increase force beyond minimum amount required to close garage door. • NEVER use force adjustments to compensate for a binding or sticking garage door.
WARNING ADJUSTMENT STEP 3 Test the Safety Reversal System Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal system MUST be tested every month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" high (3.
OPERATION IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of severe injury or death: 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls. 3. ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel. 4. ALWAYS keep garage door in sight until completely closed.
Using the Wall-Mounted Door Control THE PREMIUM CONTROL CONSOLE Press the lighted push button to open or close the door. Press again to reverse the door during the closing cycle or to stop the door while it's opening. To Open the Door Manually WARNING Lighted Push Button To prevent possible SERIOUS INJURY or DEATH from a falling garage door: • If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED.
THE REMOTE CONTROL BATTERY CARE OF YOUR OPENER WARNING LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door + operation requiring 9 1 some re7 3 kg kg 5 adjustments, particularly during + LIMIT CONTROLS FORCE CONTROLS the first year of operation. Pages 27 and 28 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully. Repeat the safety reverse test (Adjustment Step 3, page 29) after any adjustment of limits or force.
HAVING A PROBLEM? ——— 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • Verify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Install The Protector System®. • Check diagnostic LED for flashes on the motor unit then refer to the Diagnostic Chart on the following page. ——— —— 2.
Installed Safety Sensor ——— Diagnostics Located On Motor Unit ——— —— LED or Diagnostic LED "Learn" Button Your garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issue. Consult Diagnostic Chart below. Diagnostic Chart 1 FLASH Safety sensors wire open (broken or disconnected). OR 2 FLASHES Safety sensors wire shorted or black/white wire reversed.
PROGRAMMING NOTICE: If this Security✚® garage door opener is operated with a non-rolling code transmitter, the technical measure in the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code transmitter to circumvent that technical measure.
To Add, Reprogram or Change a Keyless Entry PIN NOTE: Your new Keyless Entry must be programmed to operate your garage door opener. USING THE “LEARN” BUTTON USING THE PREMIUM CONTROL CONSOLE ——— ——— —— LIGH T LOCK 1. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds. NOTE: This method requires two people if the Keyless Entry is already mounted outside the garage. 1 5 3 1.
REPAIR PARTS Rail Assembly Parts 9 1 10 2 8 7 4 3 KEY PART NO. NO. 5 6 Installation Parts 2 LOCK 5 KEY NO.
Motor Unit Assembly Parts 1 Brown Wire (Down) Contact LIMIT SWITCH ASSY. 2 DN UP Drive Gear 17 Center Limit Contact (Up) Contact 7 8 8d 8g Yellow Wire 15 5 3 Grey Wire 6 14 8b 4 8d 18 8a 8e 8f 11a 11 8c 10 11 9 12 13 16 KEY NO. 1 2 3 4 5 6 7 8 8a 8b 8c 8d 8e PART NO.
ACCESSORIES 139.53702 Emergency Key Release: Required for a garage with NO access door. Enables homeowner to open garage door manually from outside by disengaging trolley. 139.53681 SECURITY✚® 3-Function Remote Control: Includes visor clip. 139.53404 8 Foot Rail Extension: To allow an 8 foot door to open fully. 139.53680 SECURITY✚® Compact 3-Function Remote Control: With loop for attaching key ring. 139.53684 139.
ENCIA CIA CONTENIDO Introducción 2-7 Ajustes Revisión de los símbolos y términos de seguridad ..............2 Preparación de la puerta de su cochera ..............................3 Herramientas necesarias ......................................................3 Planificación ......................................................................4-5 Inventario de las cajas de cartón..........................................6 Inventario de piezas.............................................................
Preparación de la puerta de su cochera ADVERTENCIA Antes de comenzar: • Quite los seguros. • Retire cualquier cuerda o cable que esté conectado a la puerta. • Haga la siguiente prueba con su puerta para verificar que esté balanceada y que no se atore ni se pandee: 1. Levante la puerta hasta la mitad de su recorrido como se muestra. Suelte la puerta. Si está balanceada, deberá mantenerse en esa posición con sólo el soporte de los resortes. 2.
Planificación • ¿Hay otra puerta que dé acceso a la cochera? Si no es así, será necesario contar con el sistema de llave de emergencia Modelo 53702. Vea la página de Accesorios. • Observe el punto donde la puerta hace contacto con el piso. El espacio entre la base de la puerta y el piso no debe exceder 6 mm (1/4 de pulgada). Si no es así, se corre el riesgo de que el sistema de retroceso de emergencia no funcione correctamente. Vea Ajustes, Paso 3. Será necesario reparar ya sea el piso o la puerta.
Planificación (continúa) ADVERTENCIA INSTALACIÓN CON PUERTAS DE UNA SOLA PIEZA • Generalmente una puerta de una sola pieza no requiere refuerzos adicionales. Si usted tiene una puerta de material liviano y quiere reforzarla, consulte la información respecto a puertas seccionales, contenida en Instalación, Paso 12. • Dependiendo del diseño de su puerta, tal vez necesite piezas de montaje adicionales para la ménsula de la puerta (Paso 12).
Inventario de las Cajas de Cartón Su abridor viene empacado en una caja de cartón que contiene el motor y las piezas que se muestran en la siguiente ilustración. Tome nota de que los accesorios dependerán del modelo que haya comprado. Si falta alguna pieza, revise con cuidado el material de empaque ya que en ocasiones las piezas se atoran en el mismo. DESTRUYA EL HULE ESPUMA (vea la página 10).
Inventario de Piezas Antes de la instalación, organice todas las piezas en grupos como se muestra en la siguiente ilustración. TORNILLERÍA Y PIEZAS PARA EL MONTAJE Perno de 1/4-20x1-3/4 pulg. (8) Perno hexagonal de 1/4-20x5/8 pulg. (4) Tuerca de 1/4-20x7/16 pulg. (12) Manguito del cople de la polea TORNILLERÍA Y PIEZAS PARA LA INSTALACIÓN Perno de coche de 1/4-20x1/2 pulg. (2) Tuerca de mariposa 1/4-20 de pulg.(2) Tornillo de cabeza cuadrada de 5/16-9x1-5/8 de pulg.
MONTAJE, PASO 1 PRECAUCIÓN PRECAUCI Montaje del riel Para evitar QUE SE PELLIZQUE, conserve los manos y dedos lejos de las juntas cuando monte el reil. No encienda ni use el abridor hasta que llegue al paso de la instalación correspondiente, de otra manera corre el riesgo de complicar el proceso de instalación. 1. Después de abrir la caja del riel, póngala boca abajo sobre una superfície de trabajo plana. 2. Desdoble los rieles con cuidado de no golpear la junta de la varilla de conexión. 3.
Montaje del riel (Continuación) 4. Empezando en el extremo con la rueda dentada, coloque las tres secciones del riel de manera que la varilla de conexión esté alineada. (Tenga cuidado de no tocar el extremo de la varilla de conexión ya que tiene orillas afiladas.) 5. Cuidadosamente deslice los pasadores en la orilla superior de una de las secciones del riel en los orificios de la sección adyacente del riel.
MONTAJE, PASO 2 Fije el riel a la unidad del motor e instale el trole NOTA: Para facilitarle el montaje y la instalación del motor, vuelva a colocarlo dentro del hule espuma de protección, retire la espuma después de concluir Instalación, Paso 4. • Sobre una superfície plana, alinee el riel ya armado al motor como se muestra en la siguiente ilustración. • Deslice el cople sobre la polea del riel.
Soportes del riel MONTAJE, PASO 3 Tuercas de 1/4-20 pulg. Coloque las ménsulas del riel • Alinee las ménsulas con la parte trasera del riel como se muestra. • Atornille las ménsulas con los pernos hexagonales de 1/4-20x5/8 y las tuercas respectivas. Apriete firmemente con una llave de 7/16 pulg. Pernos hexagonales de 1/4-20x5/8 pulg. Ya terminó de armar su abridor de puerta de cochera, por favor lea las siguientes advertencias antes de continuar a la Sección de instalación.
INSTALACIÓN, PASO 1 INSTALACIÓN OPCIONAL DE LA MÉNSULA DEL CABEZAL EN EL CIELO RASO Determine dónde va a instalar la Ménsula del Cabezal Cielo raso sin acabado ADVERTENCIA ADVERTENCIA Pared delantera Para evitar una posible LESIÓN GRAVE o INCLUSO LA MUERTE: • La ménsula del cabezal DEBE quedar RÍGIDAMENTE sujeta al soporte estructural en la pared delantera o en el cielo raso, de no ser así es posible que la puerta de la cochera no retroceda cuando se requiera.
INSTALACIÓN, PASO 2 Orificios para la instalación de pared Instale la Ménsula del Cabezal CEILING MOUNT ONLY La ménsula del cabezal se puede fijar a la pared justo por encima de la puerta de la cochera o en el cielo raso. Siga las instrucciones que sean más adecuadas para su cochera. No instale la ménsula del cabezal en un muro falso. Si va a fijar la ménsula del cabezal a ladrillo o mampostería, asegúrese de utilizar sujetadores de cemento (no se incluyen).
INSTALACIÓN, PASO 3 Coloque el Riel en la Ménsula del Cabezal • Coloque el abridor sobre el piso de la cochera debajo de la ménsula del cabezal. Use el material de empaque como base para protegerlo. NOTA: Si el resorte de la puerta está obstruyendo, va a necesitar ayuda. Otra persona tendrá que sostener el abridor firmemente sobre un soporte temporal para permitir que el riel pueda librar el resorte.
ADVERTENCIA INSTALACIÓN, PASO 4 Instale La Sistema de Protección AD ® • Cerciórese de que la energía eléctrica no esté conectada al abridor de la puerta de la cochera ANTES de instalar el sensor del sistema de retroceso de seguridad. • Para evitar una LESIÓN GRAVE o INCLUSO LA MUERTE cuando la puerta de la cochera se está cerrando: – Conecte y alinee correctamente el sensor del sistema de retroceso de seguridad. Este dispositivo de seguridad es necesario y NO SE DEBE desactivar.
INSTALACIÓN DE LAS MÉNSULAS Asegúrese de que el abridor no esté conectado a la corriente eléctrica. Instale y alinee las ménsulas de manera que los sensores estén uno frente al otro en los lados opuestos de la puerta, a una distancia máxima de 15 cm (6 pulg.) del piso.
MONTAJE Y CABLEADO DE LOS SENSORES DEL SISTEMA DE RETROCESO DE SEGURIDAD • Deslice la cabeza de un perno de coche de 14-20x1/2 pulgada dentro de la ranura de los sensores. Use tuercas de mariposa para sujetar los sensores a las ménsulas, con las lentes de cada sensor frente a frente a ambos lados de la puerta. Cerciórese de que la extensión de la ménsula no obstruya las lentes (vea la Figura 5). • Apriete las tuercas de mariposa a mano. Figura 5 Tuerca de mariposa Perno de coche de 1/4-20x1/2 pulg.
PRECAUCIÓN PRECAUCI INSTALACIÓN, PASO 5 Coloque el Abridor Para evitar que la puerta de cochera sufra daños, apoye el riel del abridor de la misma sobre un pedazo de madera de 5x10 cm (2x4 pulg.) colocado en la sección superior de la puerta. Siga las instrucciones correspondientes al tipo de puerta de su cochera, como se muestra en la ilustración. PUERTA SECCIONAL O PUERTA DE UNA SOLA PIEZA CON CARRIL Un pedazo de madera de 5x10 cm (2x4 pulg.
ADVERTENCIA INSTALACIÓN, PASO 6 Cuelgue el Abridor AD Para evitar la posibilidad de una LESIÓN GRAVE si se cae el abridor de la puerta de cochera, sujételo FIRMEMENTE a los soportes estructurales de la cochera. Se DEBEN usar sujetadores para concreto si alguna de las ménsulas se va a instalar en mampostería. Aquí se muestran tres ejemplos distintos para la instalación; sin embargo, es posible que su cochera no concuerde con ninguno de ellos.
ADVERTENCIA ADVERTENCIA ADVERTENCIA INSTALACIÓN, PASO 7 Instale la unidad de control de la puerta Para evitar la posibilidad de una LESIÓN GRAVE o INCLUSO LA MUERTE por electrocución: • ANTES de instalar el control de la puerta, cerciórese de que la energía eléctrica no esté conectada. • Conecte el control SÓLO a cables de bajo voltaje de 24 VOLTIOS.
INSTALACIÓN, PASO 8 ADVERTENCIA ADVERTENCIA Requisitos para la Instalación Eléctrica Para evitar la posibilidad de una LESIÓN GRAVE o INCLUSO LA MUERTE por electrocución o incendio: • Cerciórese de que el abridor no esté conectado a la energía eléctrica, y desconecte la alimentación eléctrica al circuito ANTES de quitar la cubierta para establecer la conexión del cableado permanente.
INSTALACIÓN, PASO 10 PRECAUCIÓN PRECAUCI Instale las luces y lentes Para evitar un posible SOBRECALENTAMIENTO del portabombillas: • NO utilice bombillas de cuello corto ni de tipo especial. • NO utilice bombillas halógenas. Utilice SÓLO bombillas incandescentes. • Instale un foco de 100 vatios (máximo) en cada socket del abridor. Si éste se encuentra conectado, la luces permanecerán encendidas por aproximadamente 4-1/2 minutos y medio, y se apagarán por sí solas.
INSTALACIÓN, PASO 12 PRECAUCIÓN PRECAUCI Fije la Ménsula de la Puerta En el caso de puertas de fibra de vidrio, aluminio o acero ligero, ES NECESARIO colocar un refuerzo ANTES de instalar el marco de la puerta. Póngase en contacto con el fabricante de su puerta para obtener un kit de refuerzo. Siga las instrucciones que correspondan al tipo de puerta de cochera que usted tenga, como se muestra en la ilustración o en la página siguiente.
PUERTAS DE UNA SOLA PIEZA Lea y respete todas las advertencias e instrucciones respecto a los refuerzos, contenidas en la página anterior, Instalación de puertas seccionales, ya que todos los refuerzos para su puerta de una sola pieza son los mismos. • Coloque la ménsula de la puerta en el centro de la parte superior de la misma, alineada con la ménsula del cabezal, según se indica en la ilustración. Marque ya sea los orificios derecho e izquierdo o superior y inferior.
INSTALACIÓN, PASO 13 Trole interior Conecte el Brazo de la Puerta al Trole Trole exterior Siga las instrucciones que correspondan al tipo de puerta de cochera que usted tenga, como se muestra a continuación y en la página siguiente. Anillo sujetador SÓLO PARA PUERTAS SECCIONALES • Cerciórese de que la puerta de la cochera esté completamente cerrada. Tire de la manija de emergencia para desconectar el trole exterior del trole interior.
TODAS LAS PUERTAS DE UNA SOLA PIEZA Ménsula de la puerta Anillo sujetador 1. Arme el brazo de la puerta, Figura 4: • Sujete las dos secciones de los brazos de la puerta (recto y curvo) a la mayor distancia posible, de manera que dos o tres de los orificios se sobrepongan uno al otro. • Cierre la puerta y fije la sección recta del brazo a la ménsula de la puerta con el pasador de chaveta de 5/16x1-1/4 de pulgada. • Asegúrelos con un anillo sujetador.
ADVERTENCIA AJUSTES, PASO 1 Ajuste el Límite del Recorrido HACIA ARRIBA y HACIA ABAJO Al ajustar el límite del recorrido de la puerta, se regula hasta qué punto ésta se detendrá al abrir y al cerrar. Para poner en marcha el abridor, oprima el botón de control de la puerta. Haga funcionar el abridor durante un ciclo completo del recorrido.
ADVERTENCIA AJUSTES, PASO 2 Ajuste la Fuerza AD Si el sistema de retroceso de seguridad no se ha instalado debidamente, las personas (y los niños pequeños en particular) podrían sufrir LESIONES GRAVES o INCLUSO LA MUERTE cuando se cierra la puerta de la cochera. • Si el límite de la fuerza de la puerta de la cochera es excesivo interferirá con la operación adecuada del sistema de retroceso de seguridad.
ADVERTENCIA AJUSTES, PASO 3 Pruebe el Sistema de Retroceso de Seguridad Si el sistema de retroceso de seguridad no se ha instalado debidamente, las personas (y los niños pequeños en particular) podrían sufrir LESIONES GRAVES o INCLUSO LA MUERTE cuando se cierra la puerta de la cochera. • El sistema de retroceso de seguridad SE DEBE probar cada mes. • Si se ajusta uno de los controles (límites de la fuerza o del recorrido), es posible que sea necesario ajustar también el otro control.
OPERACIÓN INSTRUCCIONES IMPORTANTES DE SEGURIDAD ADVERTENCIA Para reducir el riesgo de lesiones graves o la muerte: 1. LEA Y SIGA TODAS LAS ADVERTENCIAS Y LAS INSTRUCCIONES DE OPERACIÓN. 2. SIEMPRE conserve los controles remotos fuera del alcance de los niños. NUNCA permita que los niños operen o jueguen con los botones del control de la puerta de la cochera ni con los controles remotos. 3.
Cómo Usar la Unidad de Control de Pared LA CONSOLA DE CONTROL PREMIUM Oprima el botón iluminado para abrir o cerrar la puerta. Oprima de nuevo para que la puerta retroceda en el ciclo de cierre o para detener la puerta cuando se está abriendo.
LA BATERÍA DEL CONTROL REMOTO MANTENIMIENTO DE SU ABRIDOR DE PUERTA DE COCHERA ADVERTENCIA Para evitar la posibilidad de LESIONES GRAVES o INCLUSO LA MUERTE: • NUNCA permita que los niños pequeños estén cerca de las baterías. • Si alguien se traga una batería, llame al médico de inmediato.
SI TIENE ALGÚN PROBLEMA ——— 1. La puerta no cierra y las luces de la unidad del motor parpadean: El sensor del sistema de retroceso de seguridad debe estar instalado y alineado correctamente para que el sistema de apertura de la puerta de la cochera se mueva en sentido descendente. • Asegúrese de que los sensores de seguridad estén instalados y alineados correctamente, y que estén libres de obstrucciones. Consulte la sección Instalación, Paso 10: Instale La Sistema de Protección®.
——— Diagnóstico situado en unidad del motor ——— —— LED o Diagnóstico LED Botón "Aprender" Tabla de Diagnóstico 1 PARPADEO El circuito de los sensores de seguridad está abierto (cable roto o desconectado). O BIEN 2 PARPADEOS Hay un cortocircuito en el cable de los sensores de seguridad, o los cables blanco y negro están invertidos. 3 PARPADEOS El control de la puerta o el cable tienen un cortocircuito. 4 PARPADEOS Los sensores de seguridad están ligeramente mal alineados (LED débil o parpadeante).
CÓMO PROGRAMAR EL ABRIDOR AVISO: Si utiliza este abre puertas de garaje Security✚® con un transmisor no dotado de un sistema de códigos de salto (código aleatorio), se verán circunvenidas las medidas técnicas incorporadas en el receptor del abridor para proteger contra los aparatos de captura de códigos.
Cómo Agregar, Reprogramar o Cambiar un Código de Entrada sin Llave NOTA: Su nueva Entrada sin llave debe programarse para que opere el abridor de la puerta de su cochera. CÓMO USAR EL BOTÓN LEARN (APRENDER) CÓMO USAR LA CONSOLA DE CONTROL PREMIUM ——— ——— —— LIGH T LOCK NOTA: Este método requiere dos personas si la Entrada sin llave ya está montada fuera de la cochera. 1. Oprima y suelte el botón “Aprender” de la unidad del motor. La luz indicadora de este botón estará encendida por 30 segundos. 1.
ACCESORIOS 139.53702 Liberador de la llave de emergencia: Se requiere en las cocheras que NO tienen puerta de acceso. Permite al due o de la casa abrir la puerta de la cochera manualmente desde el exterior, desconectando el trole. 139.53404 Extensión del riel de 2.40 m (8 pies): Permite que una puerta de 2.40 m (8 pies) se abra completamente. 139.53589 Ménsulas de soporte: Para cielos rasos sin acabados o en los casos en que se necesite soporte adicional, basado en la construcción de la cochera.
Get it fixed, at your home or ours! Your Home For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME® (1-800-469-4663) Call anytime, day or night (U.S.A. and Canada) www.sears.