Owner's Manual ® Bench Mode_ 1/2 HP (Maximum Developed) 5 Speeds (540 = 3600 R,PoMo) !/2 inch Chuck 104NCH DR_LL PRESS Model No° 137o219100 CAUTmON°o • o o o o o Before using this Dril! Press, read this manual and foltow at! its Safety Rules and Operating Instructions. @ustemer Safety _nstructions KnstatJation Operation Maintenance Parts List Espa_oi He_p L_n÷ t °8@@°843°1682 Sears, Roebuck Part No.
SECTION GENERAL SAFETY INSTRUCTIONS PAGE Warranty ................... Product Specifications ........... ........................................... Safety instructions ......................................................... Accessories and Attachments ............................................... Carton Contents ........................................................... Know Your DYII Press ...................................................... Glossary of Terms ....................................
GROUNDING I4. SECURE WORK. Use clamps or a vise to hold the work when practical. It's safer than using your hand and it Frees both hands to operate tool. SPECnFIC SAFETY NSTRUCTMONS FOR THE DR LL PRESS 16. MAKE SURE all clamps and locks are firmly tightened before drilling. 17. SECURELY LOCK THE HEAD and table support to the column, and the table to the table support before operating the drill press. YOUR DRILL PRESS MUST BE BOLTED securely to a workbench.
i AVAILABLE ACCESSORIES Use only accessories recommended [or this drill press. Follow instruction,s that accompany accessories, Use of improper accessories may cause hazards. UNPACKmNG AND CHECKmNG CONTENTS If any part is missing or damaged, do not plug the drill press in until the missing or damaged part is replaced, and assembly is complete.
Motor pulley Spindle pulley Depth scale stop nuts Cord clamp Depth scale pointer BASE - Supports the drill press. For additional stability, holes are provided in the base to bolt the drill press to the floor. (See "Specific Safety Instructions for Drill Presses':) DRILL ON/OFF SWITCH - Has locking feature. This feature is intended to help prevent unauthorized and possible hazardous use by children and others, insert the key into the switch to turn the drill press on.
, 6_ ASSEMBLY tNSTRUCTMONS For your own safety, never connect plug to power source outlet until af! assembly and adjustment steps are completed, and you have read and understood the safety and operating instructions. TABLE TO COLUMN ASSEMBLY (FIG. B THROUGH F) 1. Locate the worm gear, table crank, and table support lock handle from the loose parts bag. 2. Insert the worm gear (1)into the table crank handle hole (2) from inside the table support (3).
_NSTALMNG FEED HANDLES (FIG. H) 1. Locate three feed handles in the loose parts bag. 2. Screw the feed handles (1) into the threaded holes (2) in the hub (3). Tighten. , FENCE ASSEMBLY (F_G°M} t. Determine the desired location for the fence (.1). 2. Aiign the mounting holes of the fence over the table top slots. 3. Place a washer (2) on the threaded end of the knob (3). Insert the knob through the mounting hole of the fence and the table slot.
, To prevent personal injury, always disconnect the plug from the power source when making any adjustments. SQUARING TABLE TO HEAD (FIG. O, P) NOTE: The table and support has a predrilled hole with a locking pin inserted for locking thetable to a predetermined 0° horizontal position. It must be loosened to change the angle of the table. I. 2. 3. 4. 5. . QU_LL RETURN SPRING (FIG, R) The quill return spring may need adjustment if the tension causes the quill to return too rapidly or too slowly. t.
Fig. X BASIC DRILL PRESS OPERATIONS Fig. U SPEEDS AND BELT PLACEMENT (FIG. T) This drill press has 5 speeds, as listed below: 540 RPM 2610 RPM 880 RPM 3600 RPM USINGTHE FENCE (FIG. W) The fence provides a way of accurately and quickly setting up the workpiece for more precision or repetitive drilling operations. 1. Using the centerpunch or sharp nail, make an indentation in the workpiece where you want to drill. 2. Lower the drill bit to align with the indentation on the workpiece.
REMOVING CHUCK(FIG.Z) 1. Withtheswitch"OFF",openthejawsofthechuckas wideaspossible byturningthechuckcounterclockwise. 2. Tapthechuck(1)lightlywitha plastictippedhammer atthetopofchuck,untilthechuckreleases. NOTE:Placeonehandbelowthechucktocatchit when it fallsout. Fig. Z b, c. d. e. f. g. h.
-i TROUBLESHOOTING MA NTAH a NG YOUR DR LL PRESS GUIDE To aveid shock or fire hazaizd, if the power cord is worn or cut in any way, have it replaced immediately. For your own safety, turn the switch OFF and remove the plug from the power source outlet before maintaining or _ubricating your drill press. LUbrICATiON Frequentiy blow out using an air compressor or dust vacuum, any dust that accumulates inside the motor. A!l of the drill press ball beadngs are packed with 9tease at the factory.
!0" 10" DRILL PRESS PARTS MODEL LiST When servicing use only CRAFTSMAN product damage. replacement DRILL PRESS PARTS LIST MODEL NO. !37.2!9100 NO. 137.219100 parts. Use of any other parts may create a HAZARD or cause '74_ Any attempt to repair or replace electrical parts on this Drill Press may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your nearest Sears Service Center. 69 Always order by PART NUMBER, not by key number Key No.