Sears OWNERS MANUAL MODEL NO. 572.36578 CAUTION: Read Rules for Safe Operation and Instructions 115 VOLT A.C.
FULL ONE YEAR WARRANTY ON CRAFTSMAN SAW CHAIN SHARPENER _ --_._ For one year from the date of purchase, Sears will reptace this Craftsman Saw Chain Sharpener, free of charge, if it falls to work properly_ WARRANTY SERVICE IS AVAILABLE CRAFTSMAN SAW CHAIN SHARPENER STORE IN THE UNITED STATES BY RETURNING THE TO THE NEAREST SEARS This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK & COo SEARS TOWER DEPT.
GROUNDING INSTRUCTIONS This too! shou}d be grounded while in use to protect the operator from electricshock, Thetool is equipped with a three-conductor cord and three-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire, Never connect the green (or green and yellow) wire to a live terminal.
IMPORTANT OPERATING INSTRUCTIONS Check to see that the carton contains the following items illustrated on pages 4 and 5.
4 Securely mount the correct grinding stone in your tool with approximately Y," of the shank exposed between the chuck cap and thestone, Figure2 Using the appropriate side (see column 2 of chart) of the guide gauge furnished, check to see if the guide is properly positioned with repect to the grinding stone, see Figure 4.
CHAIN IDENTIFICATION CHART 10_ Tilt Grinding Stone Guide Gauge Side Depth Gauge Seffing 1 ,025 .......... ' " D25 " Blue Cat No ' • ,025 025 Yell or No 7' SherpenlngAngle =,Oregon_ Yes Yes Yes Yes " Csdton Homet'lte McCulloch SM250 Oral Cat 365 t6 Stthl 13M Windsor (Ref) 2SAP 30° 33LG 325 30" 30" 34LG 50K .325 35LG .325 ! ,025 Sabre 30=' 36581 1 Poulan , ............ I ...... NO 30" 91G 375N50 MM370 P100 375C50 MP370 P101 ...... .375 1 .
35 ° LINE SHARPEN CUTTER TEETH ONLY _ NOT THE DEPTH GAUGE GUIDE ONE OF THESE LINES TO BE PARALLEL WITH CHAIN GUIDE BAR SEE COLUMN 5 OF CHART CHECK CHAIN TYPE(FIGURE 11) OR COLUMN 4 OF CHART. FOR PROPER TILT TO BE USED WHEN SHARPENING. F_gure5 35 ° LINE GUIDE EDGE OR LINE TO BE PARALLEL WITH CHAIN GUIDE BAR. SEE COLUMN 5 OF CHART.
CUTTER CONFIGURATION CHISEL -- END VIEW MICRO CHISEL SEMI THESE TWO SHAPES OF CUTTER TEETH ARE SHARPENED WITH THE GRINDING STONE TILTED AS SHOWN_ CHIPPER & MICRO BIT CHISEL THESE TWO SHAPES OF CUTTER TEETH ARE SHARPENED WITH THE GRINDING STONE HELD HORIZONTAL.
TROUBLE SHOOTING IF YOUR SAW DOES NOT CUT AS WELl. AS IT SHOULD AFTER SHARPENING OR tT DOES NOT CUT STRAIGHT, YOU MAY HAVE A WORN OR DAMAGED GUIDE BAR, A WORN SPROCKET, OR DAMAGED LINKS IN THE CHAIN THIS CAN BE CHECKED AND REPAIRED FOR YOU AT YOUR SEARS SERVICE DEPARTMENT HOWEVER, BEFORE DOING THIS, CHECK FOR CUTTER PROBLEMS, SHARPENING ERRORS_IF YOUR CUTTERS LOOK LIKE THESE, RE-SHARPEN THEM. / Top plate angle not 35 ° caused by holding sharpener at wrong angle.
CUTTER PROBLEMS What to do if chain cuts slow or won't hold its edge: 1+ Remove chain from bar, 2+ Clean chain with solvent to remove pitch and resin, 3. Compare each cutter to these pictures, tf your chain is not cutting cuts slowly, won't hold an edge, or it cuts crooked, your problem could be caused by one or more of the fo owmg conditions: RESULT REMEDY Severe damage on either side of top and/or side plates CONDITION Cutters hit or cut material other than wood.
CRAFTSMAN CHAIN SHARPENER -- MODEL NUMBER 572.36578 The Model Number will be found on a plate attached to the Motor Housing Always mention the Model Number' in all correspondence regarding your Saw Chain Sharpener or when ordering repair parts SEE BACK PAGE FOR PARTS ORDERING Code No. '_1 Part No. ' 48o' Description Chuck Cap 298008 Ground Screw Rectifier Complete 1/8 Collel 15 99o10o 3 660217 Housin_ap _;ew 16 660046 Switch 4 990136 Front Brg.
CRRI:TSMRI! ° Sears SAW CHAIN SHA PENE OWNERS MANUAL MODEL NO. 572.36578 The model Number will be found on the plate attached to the tool. Always mention the Model Numberwhen requesting service or repair parts for your Saw Chain Sharpener.