Save This Manual For Future Reference SEAMS owners manual MODEL NO. 113.299780 Dust Collection System Serial Number mms Model and serial number may be found on the motor cover. EiiPfSMii You should record bottn model and serial number in a safe place for future use. DUST COLLECTION SYSTEM FOR YOUR SAFETY: assembly • operation • repair parts • READ ALL INSTRUCTIONS CAREFULLY. J V. Sold by SEARS, ROEBUCK AND CO., Chicago, !L. 60684 U.S.A. Part No.
FULL ONE YEAR WARRANTY ON CRAFTSMAN DÖST COLLECTION SYSTEM If within one year from the date of purchase, this Craftsman Dust Collection System fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/ DEPAffMEI^t THROUGHOUT THE UNITED STATES. This warranty applies only while this product is used In the United States.
Aa CAUTION: if using this Dust Collection System to help keep airborne wood dust in heavy usage within acceptable limits, you must regularly monitor air borne dust and maintain Dust Collection System to avoid exceeding dust limits. Each application is unique. Your maintenance schedule must, there fore, be tailored to your specific use of this Dust Col lection System. BEFORE EACH USE: 1.
GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS 1. 12. USE SAFETY G O G G LES (Head Protection) KNO W YO UR TO O L F^ead and understand owner's m anual ard labels attixed to the tool t eam its application and (im ita- W ear safety goggles (m ust com ply with ANSI Z87.1) licns as welt as its specific potential hazards pec- resistant lenses, they are NO T safety glasses. Also, at all tim es.
Introduction The Craftsm an designed to Dust capture Collection sawdust System and wood is specifically chips at the source. The fine dust is filtered by the upper bag while quency of slatic shocks in your hom e, the best rem edy is to add m oisture to the air with a console or installed hum idifier. heavy particles settle in the lower bag for easy rem oval. Do not use as a vacuum . The safety inform ation in this m anual is highlighted by the following safety alert sym bol.
introduction Tools Needed UNPACKäNG AND CHECKING CARTON CONTENTS Adjustable Wrench Screwdriver ^ WARNING: IF ANY PARTS ARE MISSING OR BROKEN, GET THE PROPER PARTS FROM SEARS BEFORE ASSEMBLY OR USING THIS DUST COL LECTION SYSTEM. Fiernove against entire thé contents Carton of carton. Contents List. Check Notify each your item Sears Store irhm ediately if any parts are dam aged or m issitig. CARTON contents LISTt Key Description CJly. A Filter/Dust Bag ................... ::.............
assembly MOUNTING FRONT PIVOTING CASTERS 1. Locale the following item s from the loose parts bag: Description Qty. A Pivoting Casters................................................. 2 B Hex Nuts* (3/8 - 16)........................................... 2 C Flat W ashers’ (3/8 x 3/4)...................................4 D Acorn Nuts*......................................................... 2 E Base Plate...........................................................1 Items are shown actual size 2.
assembly ■ 3- Carefully turn the Filtration Housing upside down so that the Motor endbei! rests against the floor. ( Place O -Ring in relief of V u ^ ; A guard must y ./ ■■ . V, . ' 'Í POINT TO ■■■, It^REAR OF . MACHINF. : 7 ' ' V v : — INLET GUARD 4. Support the opposite side of Filtration Housing wlh a block of wood. A. / ' Inlet pipe {See page 18} 5. Position/n/efGuardinlinewiththethreaded holes on the base of the Filtration Housing.
MOUNTING INLET BRACKET gli 1. Locate the following item s from the loose parts bag: Description A 2. 3. C3ty. Flat W ashers* (5/16 x 11/16 xi/i6)................... 2 B Hex Screws* (M 8 x 1.25 -12).......................... 2 C Flat W ashers *{1/4 X 1/2).................................2 D Hex Screws* (M 6 x 1 -12)................................
assembly MOUNTING FILTER/DUST BAG HOLDER TO FILTRATION HOUSING A Items are shown actual size 1. Locate the following items from the loose parts bag: Description A HexNut* (M6x1)......... ........ ...............1 B Lockwas her* (1/4) ................ .............V.1'.' C Fiat Washer* {MA x 1/2)......... .................. .1 2. Attach hex nut to threaded portion of Filter/Dust Bag Holder and place lockwasher and flat washer on nut as shown. 3.
FILTBATION HOUSING CHIP BAG ASSEMBLY LOWER FiLTRATION HOUSING 1. Insert lower Chip Bag by tilting the Metal Reinforced Band at an angle and position it through the hole in the lower Filtration Housing. 2. Tuck one side of the Band under the Sawdust Chute Extension. 3. Allow the opposite side to rest on the ridge of the opening. 4. Tug on the Chip Bag to insure proper seating. UPPER FILTER/DUST BAG ASSEMBLY 1.
operation This Dust Collection System is designed to be con nected directly to the woodworking machines. Please, use only the parts provided for maximum efficiency. 4" Diameter x 60" Hose. PVC Vulcanized rubber with wire reinforcement and 2 - 4" clamps. 4*72-1/2" direct Diameter Adapter. hookup Bandsaws, Belt to m any and Disk This connector m achines Sanders, allows including and Radial Saw Sawdust Collector.
ON/OFF SWITCH O n the rear of the Motor Housing above the Handle, is the Switch Box. The O N/O FF Switch has the ability to be turned “O N” v^hen the Red Key is properly installed. Switch to the “O N" position by m oving the switch upward- Turn the switch “O FF” by m oving downward. Rem ove the Key from the switch whenev er the saw is turned “O FF” and keep it out of the reach of children.
operation POWER SUPPLY This appliance is for use on a nom inal 120-volt circuit, and has a grounded plug that looks like the plug iltustratted below. Atem porary adapter m ay be used to connect WARNING: YOUR DUST COLLECTION SYS- this plug to a 2-pole receptacle, as shown below, if a TION. CONNECT TO A 120V, 15-AfWP, BRANCH properly grounded outlet is not available. The tem porary CIRCUIT AND USE A 15-AMP, TIME DELAY FUSE OR CIRCUIT BREAKER.
maintenance A WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF'’ AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAINING YOUR DUST COLLECTION SYSTEM. A WARNING; TO AVOID INJURY FROM ELEC TRIC SHOCK OR SUDDENLY STARTING UNIT, AL WAYS REMOVE SWITCH KEY AND KEEP UN PLUGGED WHILE UNIT IS DISASSEMBLED IN ANY WAY. ALWAYS REASSEMBLE WITH RECOM MENDED PARTS BEFORE PLUGGING UNIT IN. CHIP COLLECTING BAG REMOVAL 1. Push Band up and slide opposite edge to the m iddle opening. 2.
maintenance MOTOR ___ CAUT50N; To avoid eye Injury or adverse reaction to dust, high air pressure should not be used especially In poorly ventilated areas. Excessive dust in m otor could cause excessive heaî in m otor. Every effort should be m ade to prevent foreign m aterial from entering the m otor.
PROBLEM Excessive noise. REMEDY SUGGESTED PBOBABLE CAUSE 1. M otor 1. Have motorchecked by qualified s^rvfce technician. Repair service is avaiable at your nearest Sears store. M otor fails to devel op full power. NO TE: LO W VO L TAG E: (Power out put of m otor de creases rapidly with decrease in voltage at m otor term inals.
repair parts PARTS LIST FOR CRAFTSMAN DUST COLLECTION SYSTEM MODEL 113.
repair parts PARTS LIST FOR CRAFTSMAN DUST COLLECTION SYSTEiyi MODEL 113.299780 Always order by Part Number > not by Key Number. Item Part No. No. Description Item Part No. No. 27 819198 Description W ashe r. Flat 5/16 X 11 /16 1 819166 2 819172 3 819187 A Switch 28 819196 4 819302 A Key, Switch 29 819207 5 819189 ^ Cord with Plug 30 819199 6 819191 7 31 32 Base Caster, Pivoting * Nut,. Hex 3/8 -16 8 STD833025 819192 819203 STD541037 33 STD551037 * W asher.
'X r smm owners manual DUST COLLECTION SYSTEM Service is available by returning this unit to the nearest Sears Service Center/Department through out the United States. SERVICE MODEL NO. 113.299780 Dust Collection System Mode! and serial numbers may be found on the Motor Cover of your Dust Collection System. HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS. ALWAYS GIVE THE FOLLOWING INFORMATION; PART NUMBER PART DESCRIPTION MODEL NUMBER 113.
