DC Remotes DR10 The DR10 is a telephone style DC Remote designed to provide control of a remotely located radio base station or repeater over an in house or leased metallic wire pair. The DR10 uses a simple dip switch to select the desired control current format and other features. No PC or programming cables required.
DR Series Specifications Power Requirements 120 VAC, 60Hz for wall pack operation Audio Output to Speaker 2 Watts minimum (in compression) into 8 ohms with less than 3% distortion using supplied power pack. Compression Less than 3 dB increase in output with 30 dB increase beyond threshold of compression. Line input Adjustable, -20 dBm minimum. Frequency Response +/- 3dB from 300 to 3000 Hz. 1000 Hz reference. Signal to noise ratio 50 dB below operating levels.
DC Termination Panels DTP Series The DTP Series DC termination panels provide a reliable, cost effective method of interfacing a DC remote control system to virtually any two-way radio. There are three basic models in the DTP series. The DTP1 provides TX and RX functions. The DTP2 provides TX, RX and Monitor functions. The DTP3 provides TX, RX, Monitor and F1/F2 functions.
DC Termination Panel Specifications DTP Series Power Requirements +11 to +16 Vdc @ 35 mA idle. Modulation Output 2 mVrms to 565 mVrms into 600 ohm load with 0 dBm input on phone line. Line impedance 600 ohms. Dimensions/Weight 5" x 4" x 1" inches - 1 lbs. RX Input level 88 mVrms to 880 mVrms ( Level required to provide 0 dBm to phone line. ) Connections RJ11 jack for phone line. Screw terminals for radio connections.
Tone Remotes TR10 The TR10 is a telephone style Tone Remote designed to provide control of a remotely located radio base station or repeater over a voice grade wire pair. The TR series uses the E.I.A. standard sequential tone format which provides 2175 Hz. guard tone, 1950 Hz transmit key tone and 2175 Hz. hold tone.
TR Series Specifications Power Requirements 120 VAC, 60Hz for wall pack operation Audio Output to Speaker 2 Watts minimum (in compression) into 8 ohms with less than 3% distortion using supplied power pack. Compression Less than 3 dB increase in output with 30 dB increase beyond threshold of compression. Line input Adjustable, -20 dBm minimum. Frequency Response +/- 3dB from 300 to 3000 Hz. Except at notch frequency. 1000 Hz reference.
Multi Frequency Tone Remotes TR10-4F The TR10-4F is a telephone style tone remote designed to provide control of up to 4 frequencies on a remotely located base station radio over a voice grade wire pair. The TR10-4F uses the E.I.A. standard sequential tone format which provides 2175 Hz guard tone, 1950-1650 Hz function tones, 2050 Hz monitor, and a 2175 Hz hold tone.
TR10-4F-16F Specifications Power Requirements Audio output to speaker Compression Line Input Frequency Response Signal to noise Line impedence Line Outpuut Control Tones Dimensions/ Weight Connections Option -4W -FD -DE -UE1 -WM -BLK -DM -GM 120 VAC, 60Hz for wall pack operation 2 watts minimum (in compression) into 8 ohms with less than 3% distortion using supplied power pack Less than 3 dB increase in output with 30 dB increase beyond threshold of compression.
Tone Termination Panels TTP1(N) The TTP1(N) is an EIA standard tone termination panel that can be interfaced to virtually any radio. Standard features of the TTP1(N) include: tone detection AGC (eliminates line in level adjustments), modular and screw terminal connections, jumper selectable 2 wire, 4 wire, or full duplex, and LED status indicators. The only available option for these units is a case option. -C/TTP(N) This unit will interchange with the present TTP1 as the connector styles are identical.
Tone Panel Specifications Input voltage Line impedence Line ouput to phone line Line ouput from phone line RX input from radio Notch filter Dimensions TTP(N) series TTP(N)-C/MR series TTP216 Control Tones: Control function outputs Option subject to change without notice +12 to +13.8 VDC @ 150 mA (18mA idle) 600 ohms +10 dBm max. preset to 0 dBm -40 dBm to +10 dBm (function tone referenced) 70 mVrms or greater 2175 down 50 dB from 1000 Hz reference 5.3” wide x 1” high x 5” deep - unenclosed 5.
Telephone (972) 429-7165 Fax (972) 429-7165 (800) 869-9128 CPI Communications, Inc. 941 Hensley Lane Wylie, TX 75098 TONE TERMINATION PANELS TTP1, TTP2 The TTP1 or TTP2 provide the interface between tone remotes using the industry standard tone format and any two-way radio base station allowing remote control of a two-way radio base station or repeater over a 600 ohm voice grade audio path. Interfacing the TTP1 or TTP2 termination panel is straight-forward.
Specifications Subject to change without notice. TTP1 - Single frequency with monitor, TTP2 - Two frequency with monitor Size: 2.9" wide .75" high 5.25" long General: Input voltage: +12 to +13.8 Vdc @ 150 mA (18 mA idle) Line impedance: 600 ohms Line output level: + 7 dBm max.
Local Extensions LE10 The LE10 is a telephone style local extension designed to provide remote control of a conventional or trunked radio base station or repeater at distances up to 1000 feet. The LE series is easily configured for use with virtually any radio and allows up to 25 units to be paralleled off a single radio. Advanced features of the LE series include the ability to hear transmissions made from parallel units as well as those made using the radio microphone.
LE Series Specifications Power Requirements 12 VDC to 16 VDC @ 35 mA idle, 175 mA maximum. Fused on circuit board. Receive Audio Input Level 88 mVRMS to 880 mVRMS to provide full speaker output. Audio Output to Speaker 1 Watt into 8 ohms with 13.8 VDC supply or using -WP option. Transmit Audio Output 2 mVRMS to 565 mVRMS into 600 ohms. Frequency Response +/- 3dB from 300 to 3000 Hz. 1000 Hz reference. Dimensions 9" x 4" x 7" inches Weight LE10 - 3 lbs, LE20 - 4 lbs, LE30 - 3 lbs, LE40 - 4 lbs.
DC to Tone Convertor DTC1 DC to TONE CONVERTOR TB1 CONNECTIONS (214) 437-5320 (800) 869-9128 1 - GROUND 2, 3 - AC INPUT 4, 5 - TONE PAIR 6, 7 - DC PAIR SEE MANUAL FOR DIP SWITCH SETTINGS TB1 LINE INPUT MOD OUT 1 2 3 4 5 6 7 8 TONE OUT 1 2 3 4 5 6 7 Description The DTC1 DC to Tone convertor converts your existing DC remote control system to the industry standard sequential tone format used by Motorola, GE, and other manufacturers.
DTC Series Specifications Power Requirements 12VAC @ 300ma. Wall pack provided. Unit may also be powered directly from a 12 VDC source. Controls Line Input, Mod Out, Tone Out Line input/output impedance 600 ohms or 5000 ohms bridged. Balanced input. Control Tones Guard tone=2175 Hz, Function tones=1950 Hz, 1850 Hz or 2050 Hz, Hold tone=2175 Hz for duration of PTT Tone Duration Guard tone = 140 ms ± 1%; Function tones = 40 ms ± 1% Line output level +10 dBm maximum into 600 ohm line, adjustable.
Multi-Channel Products for Motorola's® Radius® & Maxtrac® MCR210 The MCR210 is a telephone style remote control unit designed for use with the Radius 200 series, GM300, SM120, M1225, M1225LS and Motorola's Maxtrac 300 conventional radios. The remote provides LED displays for channel indication, channel up and down buttons, PTT indicator, on-hook PTT capability, monitor button and indicator, intercom button , scan button and indicator and speaker volume control.
MCP200 series Termination Panel s The are five models of MCP200 series termination panels. The MCP200 - for use with Maxtrac 300 series and Radius M200 series radios; the MCP200G - for use with Radius GM300 radios; the MCP200M - for use with Radius M1225 20 ch; the MCP200MLS - for use with Radius M1225LS radios; and the MCP200S - for use with Radius SM120 radios. All models consists of two parts. The first is a small adaptor board that is installed in the radio.
Multi-Channel Products for Kenwood® Conventional Radios MCR411A The MCR411A is a telephone style remote control unit designed for use with Kenwood's -90 series conventional radios. The remote has an LCD displays for group and channel indication and 9 character alpha channel alias. The remote provides group and channel up and down buttons, PTT indicator, on-hook PTT capability, monitor button and indicator, intercom button , scan button and indicator, privacy feature, and speaker volume control.
MCR / TSR Series Specifications MCR411, TSP412 alpha MCP401/ TSP402 - Termination Panel Power Requirements 12 Vdc at 300 mA (alpha = 500 mA) Power requirements 13.6 Vdc, limited to 100 mA. Power taken from radio accessory jack. Indicators Channel/Group, System/Group, PTT, Scan and Monitor, Privacy TX Control Adjusts audio level to the radio microphone input. RX Control Adjusts audio level to phone line. Adjustable from -20 dBm to +10 dBm.
Multi-Channel Products for Kenwood® Conventional Radios MCR410 The MCR410 is a telephone style remote control unit designed for use with Kenwood's TK630, TK730 and TK830 conventional radios. The remote provides LED displays for channel indication, channel up and down buttons, PTT indicator, onhook PTT capability, monitor button and indicator, intercom button , scan button and indicator and speaker volume control.
MCR / MCP400 Series Specifications MCR410, MCR420 and MCR410 alpha MCP400 - Termination Panel Powe r Requirements Power requirements 13.6 Vdc, limited to 100 mA. Power taken from radio microphone jack. TX Control Adjusts audio level to the radio microphone input. RX Control Adjusts audio level to phone line. Adjustable from -20 dBm to +10 dBm. 12 Vdc at 300 mA (alpha = 500 mA) Indicators Controls Channel, PTT, Scan and Monitor.
Multi-Channel Products for Midland's® Syntech® XTR Radio MCR310 The MCR310 is a telephone style remote control unit designed for use with Midland's Syntech XTR conventional underdash radios. The remote provides a handset with PTT, LED displays for channel indication, channel up and down buttons, PTT indicator, on-hook PTT capability, monitor button and indicator, P-scan button and indicator, N-scan button and indicator, A/D button and indicator, intercom button and speaker volume control.
MCR / MCP300 Series Specifications MCR310 and MCR320 Powe r Requirement s .......................................... . 12 Vdc at 300 mA Indicator s ............................................................ . Channel, PTT, and Monitor. Control s .............................................................. . Channel up/ down, PTT, P-Scan, N-Scan, Monitor, Interco , A/D, and m volume control. Line inpu t leve l .................................................. .
Multi Channel Products for Motorola CDM1550(LS) radios MCR211A The MCR211A is a telephone style remote control unit designed for use with Motorola's CDM1550 and CDM1550LS radios. The remote has an LCD displays for channel and zone indications and 9 character alpha channel alias. The remote provides channel and zone up and down buttons, PTT indicator, on-hook PTT capability, monitor button and indicator, intercom button , scan button and indicator, privacy feature, and speaker volume control.
MCR/MCP Series Specifications MCR211 Alpha MCP200C - Termination Panel Power Requirements 12 Vdc at 300 mA (alpha = 500 mA) Power requirements 13.6 Vdc, limited to 100 mA. Power taken from radio microphone jack. Indicators Channel, Zone, PTT, Scan and Monitor, Privacy TX Control Adjusts audio level to the radio microphone input. RX Control Adjusts audio level to phone line. Adjustable from -20 dBm to +10 dBm. Intercom/Test button Used for test mode on power up, then for intercom.
Dealer Price Guide Communications, Inc. DC Remotes Model # Description List Dealer DR10 Telephone style DC remote with handset. Features off-hook monitor, front panel PTT, PTI circuit, line continuity sensing, cross mute, and 2 watt audio. Control currents are dip switch selectable. Jumper selectable trunking mode - status tones heard over handset earpiece. (Ash color) $284.50 $185.00 DR20 Console style DC remote with desk microphone.
DC Termination Panels Model # Description List Dealer DTP1 Single frequency DC termination panel features audio amplification in both directions, dip switch selection of control currents, LED indication of panel status and on board squelch circuit. This unit will interface to virtually any two way radio. Board only - case option available. $125.50 $81.50 DTP2 Same features as the DTP1 with monitor function. $150.50 $97.50 DTP3 Same features as DTP2 with two frequency selection. $192.50 $125.
Tone Remotes Model # Description List Dealer TR10 EIA standard single frequency telephone style tone remote with handset. 1950 Hz function tone, 2050 Hz monitor, and 2175 Hz hold tone. Features on and off-hook monitor, front panel PTT, parallel transmit indication, cross mute, and 2 watt audio. PTI and x-mute are hardwire. (Ash color) $386.25 $251.00 TR20 Console style desk microphone version of the TR10. $540.40 $351.25 TR30 Console style internal mic version of the TR10. $386.25 $251.
Tone Termination Panels Model # Description List Dealer TTP1(N) Single frequency plus monitor tone panel with jumper selectable 4W/FD operation, tone detection AGC, and LED indicators for panel status. 1950 Hz PTT and 2050 Hz monitor. $360.00 $235.00 TTP2(N) Two frequency version of the TTP1(N). F2 is 1850 Hz. $395.00 $260.00 TTP216 Enclosed 16 frequency tone termination panel. 1950-450 Hz. User programmable function tones with 14 pre-sets.
Model # Description TTPBCD BCD relay output panel is capable of 10 channel selection . 1950-1050 Hz PTT and 2050 Hz monitor $607.75 $395.00 MR200 Single frequncy plus monitor enclosed tone panel plugs directly into the microphone jack on certain radios. For Maxtrac 100,300, Radius M10,100,120,M200, GM300, SM50, SM120, M1225, GTX, MCS2000, and CDM series radios $461.50 $299.95 JM200 Same features as the MR200 for use with the E.F. Johnson Challenger or 8600 series radio. $461.50 $299.
Specialty Remote Systems for Kenwood mobile radios Model # Description (90 series mobiles) MCR411A Telephone style remote with handset for -90 series Kenwood radios. $692.25 Provides Group/Channel display with a user programmable 9 character alpha numeric channel identifier, remote Group/Channel change, scan, monitor, front panel PTT, intercom, and privacy. MCR411A-DM Console version of the MCR411A with desk microphone. List Dealer $450.00 $720.00 $500.
The following multi-channel remotes for the various Motorola models can be used together in a single system. Alpha and non alpha remotes will function together in the same system using 2 wire operation. Only the alpha remotes and termination panels are capable of full duplex operation. Non alpha remotes can not be used in a full duplex system. Model # Description List Dealer MCR210A Telephone style remote with handset.
Model # Description (Maxtrac 800 and 900 Mhz) List Dealer TSR210A Telephone style remote with alpha numeric display features a 10 character user programmable channel identifier. Features system and group selection, scan and monitor functions, front panel PTT, and intercom between parallel remotes. Dip switch selectable FD operation. $692.25 $450.00 TSR210A-DM Console style TSR210A with desk microphone. $720.00 $500.00 TSR200 Telephone style remote with handset.
Options for Specialty Remotes Option Description List Dealer -DE 12 key DTMF encoder $92.50 $60.00 -UE1 -UE1P Panel mounted 12 key multi-format encoder for non MCRX20 models. $169.25 Panel mounted 12 key multi-format encoder for MCRX20 models. $215.25 $110.00 $140.00 -D Allows the use of the MCP200 or TSP200 on the Desktrac. $23.00 $15.00 -4W/FD Four wire / full duplex option for MCP/TSP termination panel. Not compatible with non-alpha MCR or TSR remotes. Not available on TSP101. $23.
RETURN POLICY All returns must be made within 30 days of invoice date, after 30 days all sales are final. Sales of special orders or custom units are final on date of sale. Returns that are unopened will be subject to a restocking fee equal to 20% of the invoice price. Returns that have been opened will be subject to an additonal testing or refurbishing fee. If the returned item shows a defect that is not covered under warranty, you will be charged normal rates for repair.