User Manual v1.0 2.6.1 Verify Box Contents 2. Open the package and verify all elements are available according to the following table: Table 9: HEU Package Items List Item Quantity Image Part Number HARDWARE – provided in the box Headend Unit Chassis (with blank panels on RIM and one PSM slots) – includes factory installed Fan Module (FAM) in chassis rear 1 FAM Fan Module (FAM) – single unit hosting 4 fans (factory installed in chassis rear) 1 RJ45/RJ45 communication cable L=2m-2.
User Manual v1.0 Item Quantity ERFC (Expander Cable) - RF interface cable to HEU; 9 pin SMP to SMP connector Available in five different lengths: • ERFC16: L= 16 in • ERFC24: L= 24 in • ERFC34: L= 34 in • ERFC40: L= 40 in • ERFC59: L= 59 in DCM kit 1 Image Part Number Optical cables Up to 900 meters LC/UPC SM DX SFP+ Pluggable Transceivers (hot-pluggable optical transceiver module); Support for option 8 line-rate 10.
User Manual v1.0 Item Quantity Image Part Number Controller Module Kit (HCM or ACM - according to order) • dHCM Kit (Headend Control Module) – installed in Main HEU unit; enables remote/local management of all hosted units • ACM Kit (Auxiliary Control Module) – installed in Auxiliary HEU units; provides management connections for the Auxiliary HEU. Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 2.6.2 Mount the Chassis in a Rack Notes: • One HEU supports connections to up to four IHUs • IHU chassis requires 4U rack height availability • Rack nuts and screws not provided 1. Determine the location of the HEU in the rack while considering additional HEU and IHU units and the lengths of the available ERFC cable. 2. Refer to Error! Reference source not found. for planning the rack positions. 3.
User Manual v1.0 2.6.3 Install the Modules in the Chassis Note: For modules with ejectors (i.e. RIM, RIX OIM, OIX, DCM and HCM/ACM) – verify that the ejectors are completely open when inserting in dedicated slot and then push in until the module clicks in to the backplane. See Figure 13: Module Captive Screws and Ejectors below, that shows an example of module type captive screws and ejectors. 2.6.3.1 Install the DCM Module 1. Slide the DCM to its slot in the HEU chassis 2.
User Manual v1.0 Figure 13: Module Captive Screws and Ejectors Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 2.6.4 Connect the Cables 2.6.4.1 Ground The grounding connection is performed via a two-hole, standard barrel grounding lug located on the HEU rear panel. • For use with stranded copper wire conductors • 10-14 AWG • Holes - 1/4 inch Grounding Lug (Chassis Rear) 2.6.4.2 Connect RIMS to RF Source(S) For each RIM - connect the external RF source to the corresponding RIM (service specific) Simplex or Duplex QMA connectors: a.
User Manual v1.0 2.6.4.3 RIX 10 MHz Pilot Clock Connections Notes: • This section is only relevant for configurations with additional IHU or HEU and OIU units. • The REF IN and REF OUT pilot clock ports must be connected in a closed loop. • Both RIX modules of each chassis must be connected. • The jumper cables are routed through the sides of the cable management tray and door.
User Manual v1.0 2.6.4.4 RIX to OIX Connections Note: Each RIX module supports connections to up to two IHU. 1. Using the appropriate length ERFC cable (according to distance of available OIX port) connect the HEU RIX module 9-Pin connector to the corresponding connector on the IHU OIX module. HEU RIX IHU OIX 2. Refer to TBD for schematic diagram of coax connections in a maximum HEU-OIU configuration of 4x4 where all HEU units are connected to all IHU units.
User Manual v1.0 2.6.4.5 Management Connections Notes: • One RJ45/RJ45 management cable is provided with each headend unit (i.e. HEU/IHU). • Up to 7 ACMs are connected to a single HCM, where the connection between the units is using RJ45 cables.
User Manual v1.0 2.6.
User Manual v1.0 Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 3. Session Access and Main Menu Once all the system elements are installed, the system administrator can log in to the system GUI and perform initial configurations. It is recommended to begin working with the Corning® Everon™ 6000 by following these steps: 1. Review the supported access options (section 1.1) and default network settings (section 1.2). 2. Open a local session to the HCM (section 1.3). 3. Configure the network settings to allow future remote access (section 1.6). 4.
User Manual v1.0 3.3 Opening a Local Session Below are the instructions for opening a local management session in order to perform basic system configurations via the system GUI. ➢ To Open the system GUI 1. Connect a computer (i.e.
User Manual v1.0 Follow these steps to find the settings above (the steps may vary slightly depending on the OS version used): 1. Go to the Control Panel. 2. Select Network and Internet. 3. Select Network and Sharing Center. 4. Select Change adapter settings (in the left menu). 5. Right click Local Area Connection and select "Properties". 6. Select Internet Protocol Version 4/6 and click "Properties". The window below appears: 3.
User Manual v1.0 4. For first-time authentication use the following default values: Username: admin Password: default provided with your system. Group: leave blank. IMPORTANT! For security reasons it is highly recommended to immediately change the password (via the "Admin" -> "Security" tab) and log in again using the new password. 5. Click the "SIGN IN" button. System GUI main screen appears. SCREEN 3.
User Manual v1.0 Main Menu Parameters Display area System tree / sub-options Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 3.5 Main Menu Options The table below lists the management options provided by the main menu: Table 10: Main Menu Options Icon View the system topology and information about the different system elements. View all system events and generate reports. Perform initial system configurations. This option is only visible to the system administrator. Administrative options to perform system configurations, implement updates, define and monitor user's activity.
User Manual v1.0 3.6 Remote Management This section describes the configurations required for remote session access using Ethernet connection via the LAN port. To configure the HCM LAN port 1. In the main menu bar, click 2. Select the "IPv4 LAN Port" or "IPv6 LAN Port" tabs and click the 3. For Static IP Address set DHCP as "None set the IP address, subnet mask and default gateway manually to legal values, which aren't used by other system elements.
User Manual v1.0 4. Initial Commissioning This section describes all the initial configurations that must be done by the system administrator. 4.1 Main Menu Config Option The option in the main menu is only visible to the system administrator. This section describes the configurations that only the system administrator can perform. 4.1.1 Site config When choosing the Site Config option from the Config submenu, the following screen appears: An image represents each relevant site.
User Manual v1.0 2.1.1.1 Module Owner The Module Owner tab shows all system chassis with the RIMs inside each chassis. The user can click on a RIM to have the carrier name displayed. This view is read only carrier assignments can only be done via the Channels tab in the main menu. changes to RIM 2.1.1.2 RF Path The RF Path tab enables the user to easily see which RIMs belong to which service group.
User Manual v1.0 2.1.1.3 Max Input The Max Input tab allows the configuration of three parameters for each RIM: Max Expected Power UL Gain Mode UL Gain Value A single RIM can be clicked to be configured. Alternatively, a group of RIMs can be configured by selecting a service group, chassis or a frequency band. Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 4.1.2 Amplifier Sharing The Amplifier Sharing tab shows all supported frequency bands and the carriers sharing each band. The carriers are sharing the power associated with the frequency band. 4.1.3 TDD Config The TDD Config tab allows the user to config TDD related parameters per stack. Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 4.1.4 Adjustment The Adjustment tab allows the user to start the adjustment process. During adjustment the status and relevant information are updated for each process. 4.2 Create new user groups Initially the system administrator is the only system user. In order to enable other users to log in to the system the system administrator must create user groups for the different providers/carriers.
User Manual v1.0 To create a new group 1. Log in as the system administrator. 2. In the main menu bar, click 3. Click the button enter the new group name (alphanumeric characters only, no spaces) and click OK. Up to 31 groups can be created. 4. The new group name is added to the list of defined groups and the group administrator is automatically created with the following default authentication: .
User Manual v1.0 5. System Graphical User Interface (GUI) This section describes the system GUI options. 5.1 Main GUI Options The main menu options are described below. 5.1.1 Devices Screen Element Management The Devices option provides visual information on the system layout, connected units and hierarchy, alarms etc. The system elements hierarchy tree is detected via an auto-discovery process, executed upon system start-up. The system u coding icons are detailed in the table below.
User Manual v1.0 Table 11: Alarm Icons Icon Unmasked Red circle Green circle Orange circle Masked Indicates There is a major alarm related to the element No alarm is related to the element There is a minor alarm related to the element Unit is disconnected Indication on DRU-DCM connection Any status changes are reported via SNMP to a monitoring system. If an alarm is masked, it isn't reported to the monitoring system. In addition, system events log lists only unmasked alarms which were set or unset.
User Manual v1.0 Below are lists of all alarms per system element type and their meanings. Table 3: HCM Alarms Descriptions Alarm Name HW Failure Description Faulty HCM hardware. Adjustment Failure Unsuccessful Adjustment procedure. Installation Failure Faulty physical installation between chassis. SW Release Mismatch A module (or modules) in the system do not have the defined active release. Several modules may not have corresponding software versions.
User Manual v1.0 Table 5: RIM Alarms Descriptions Alarm Name Description Overall Status Overall status of enabled (unmasked) alarms. HW Failure Over Temperature/Temp Inconsistent Version/SW Version Adjustment Fault Service State Hardware failure during startup or during normal operation. Ambient temperature inside the RIM is more than 75°C. The module does not have the defined active release. Unsuccessful adjustment procedure for the selected module. Service has been disabled by the user.
User Manual v1.0 Table 7: DCM Alarms Descriptions Alarm Name Description Inconsistent Version The module does not have the defined active release. Temperature Ambient temperature inside the DCM is more than HW Failure DCM faulty hardware upon initialization or during operation. Adjustment Fault Unsuccessful Adjustment procedure. Overall Optical Links Overall status of enabled (unmasked) alarms in output optical links.
User Manual v1.0 Alarm Name Description TDD_OUT_OF_SYNC PA_OVERCURRENT CONNECTION_ERROR The following table lists alarms which are relevant to the CPRI protocol. These alarms are relevant for the optical links some of the system elements have (see sections 1.3.1.5-7 below). Table 9: CPRI Alarms Descriptions Alarm Name Description LOS Loss of signal. LOF Loss of frame synchronization. RAI Remote alarm indication. SDI SAP (service access point) default indication.
User Manual v1.0 5.1.1.2 HCM Device Form The device form of an HCM has a single tab: Info. The Info tab has general information about the system element: Table 10: HCM Info Device Form Fields Field Information Name Chassis Serial Number Serial Number The name of the element as it appears in the system tree. The serial number of the chassis the HCM resides in. The serial number of the HCM. IP Address The IP address of the HCM. SW Version SW version updated in HCM.
User Manual v1.0 5.1.1.3 ACM Device Form The device form of an ACM has two tabs: Info and Power Supply. The Info tab has general information about the system element: Table 11: ACM Info Device Form Fields Field Information Name Chassis Serial Number Serial Number The name of the element as it appears in the system tree. The serial number of the chassis the ACM resides in. The serial number of the ACM. SW Version SW version updated in ACM. IP Address The IP address of the ACM.
User Manual v1.0 5.1.1.4 RIM Device Form The device form of a RIM has at least two tabs: Info and RF Parameters. A RIM which supports TDD also has a TDD tab in its Device Form. The Info tab has general information about the system element: Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 Table 12: RIM Info Device Form Fields Field Information Name The name of the element as it appears in the system tree. Chassis Serial Number The serial number of the chassis the RIM resides in. Serial Number The serial number of the RIM. Slot Index The number of the slot in the chassis the RIM resides in. Band Type Band number according to LTE frequency bands. Band number is mapped directly to a frequency range. SW Version SW version updated in RIM.
User Manual v1.0 Table 13: RIM RF Parameters Device Form Fields Field Information DL Power Detector[dBm] Power of base station down link transmission. Range is -10 to +37[dBm]. Automatic Limit Control (ON/OFF switch) Service State (ON/OFF switch) Max Exp. Power [dBm] Service State OFF simulates RIM is disconnected. Transmission disabled by user. User defined max power for the base station transmission. An alarm is triggered if the value in DL Power Detector field deviates from this value.
User Manual v1.0 A RIM which supports TDD (Time Division Duplexing) has an additional tab TDD: Table 15: RIM TDD device form fields Field Information UL/DL Allocation Mode 0 to 6 CP Type Cycle Prefix: Normal/Extended S Frame Format 0 to 8 Central Frequency (MHz) Low 2526 Medium 2593 High 2660 Custom 2526 to 2660 (0.1MHz steps) Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 5.1.1.5 DCM Device Form The device form of a DCM element has two tabs: Info and Optical Links. The Info tab has general information about the system element: Table 16: DCM Info Device Form Fields Field Name Information The name of the element as it appears in the system tree. Chassis Serial Number The serial number of the chassis the DCM resides in. Serial Number The serial number of the DCM. Slot Index The number of the slot in the chassis the DCM resides in.
User Manual v1.0 The Optical Links tab has information about the optical links of the DCM. Each optical link has the colour of the most severe alarm related to it. In the example below links 1 and 3 have no alarms, link 2 has a major alarm and link 4 has a minor alarm. 5.1.1.6 DRU Device Form The device form of a DRU element has two tabs: Info and Optical Links.
User Manual v1.0 Table 17: DRU Info device form fields Field Information Name Serial Number The name of the element as it appears in the system tree. The serial number of the DRU. SW Version SW version updated in DRU. IP Address The IP address of the DRU. Identify (ON/OFF switch) When the switch is ON the DRU LEDs are blinking (can be used to identify the specific module among many other modules). The Optical Links tab has information about the optical links of the DRU.
User Manual v1.0 5.1.1.7 dLRU/dMRU/dHRU Device Form The device form of a dL/M/HRU element has three tabs: Info, Supported Bands and Optical Links. The Info tab has general information about the system element: Table 18: dLRU/dMRU/dHRU Info Device Form Fields Field Information Name Serial Number SW Version HE Chassis SN The name of the element as it appears in the system tree. The serial number of the dL/M/HRU. SW version updated in dL/M/HRU.
User Manual v1.0 The Supported Bands tab lists all the bands supported by the dL/M/HRU. clicking on a band will show the band information. In the example below information about the AWS band is displayed: Bands supported The Optical Links tab has information about the optical links of the dL/M/HRU. Each optical link has the colour of the most severe alarm related to it. When clicking on one of the inputs, information about the link appears.
User Manual v1.0 5.1.1.8 DRU to DCM Connection Example: DRU to DCM(s) Connection The following figures indicate connectivity between DRU and DCM(s). For DRU the device status per DCM is shown in the following manner: Connected Click to access The number of arrows is the number of DCMs the DRU is connected to. The user may skip between the the arrow of the desired DCM.
User Manual v1.0 5.1.2 Events Screen The events option provides indications on the different events in the system. This includes: alarms, upgrades, admin-actions, etc. The events may be sorted according to the time they occurred, severity, source, etc. The user may choose to display the alarms history, masked alarms or active alarms.
User Manual v1.0 5.1.3 Admin Screen The admin screen allows the user to define administrators, update credentials, upgrade firmware, generate reports and other admin options as detailed in the table below. When choosing the Admin from the main menu the following screen appears: Admin suboptions Selected option display Table 20: Admin Screen Sub Options Tab Firmware Update HCM FW and enable FW auto synchronization. Lists which FW version is currently installed and what versions are available.
User Manual v1.0 5.1.3.1 Firmware The Firmware tab allows the user to upgrade the firmware version of the system elements. version, and restarting the HCM. The new software can be activated either immediately or at a more convenient time as defined by the user. The procedures are performed via the Firmware submenu. By default, Auto Sync option is enabled, hence the software of all installed devices at the site is updated to the software version of the HCM.
User Manual v1.0 Activate the new firmware either immediately by using the time by using the 4. icon or at a scheduled (user defined) icon. After the new firmware is activated, and the controller automatically restarts: Log in to the system. The new firmware version should appear in the "Currently Installed" area: 5.1.3.2 Security Access security is provided by definitions of user groups created by the system administrator.
User Manual v1.0 Level Description Operator R/O access to Devices and Events screens. Installer R/O Access to Devices and Events screens. Write access to free text parameters to allow the definition of location and identification information. RF Tech Access to the Devices, Config, Events and Channels screens: Write access to all RF parameters. R/O to all other parameters. IT Tech Access to the Devices and Admin screens: Write access to all non-RF parameters.
User Manual v1.0 Note: A group can have up to 20 users. Maximum of 31 groups and 500 users per HCM. 4. The new user account is added to the group list. For example: ATNT group has three users defined: admin, RF and Installer. 5. Users can be removed from the group list using the can be modified using the the group. icon. User information, including password, icon.
User Manual v1.0 Enter the old password and the new password, confirm the new password and then click "SAVE". The password must consist of at least 8 alphanumeric characters, no spaces. Weak passwords will not be accepted. Note: The group admin can change the passwords of the users in his group as explained in the flow above: "To add users to a group" step 5. Session Access and Timeout.
User Manual v1.0 5.1.3.3 SNMP Config 5.1.3.4 Reports The types of reports which can be generated are listed under "Reports" (these are the general reports) and "Inventory Reports". The reports can be generated either in XLS or in PDF format. In addition, "Device Logs" can be exported for troubleshooting by the system administrator.
User Manual v1.0 Inventory Reports Inventory reports provide detailed information in the selected format of "All Devices" or a specific system element. The information includes location, installed versions, IP Address, and more. Device Logs Device logs are the HCM logs and they are accessible to system admin level users only; used for tech support troubleshooting. 5.1.3.5 IP Settings The IP Settings tab allows the configuration of all stacks in the current MS group.
User Manual v1.0 Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 5.1.3.6 Backup The Backup tab allows the system administrator to backup and restore system configurations. Other users The system administrator selects the configuration of which stacks to back up to a file and the Micro SD card inserted in the HCM (see section * for SD card slot location). It is recommended to perform backup after each configuration change. To backup and restore configurations 1. In the main menu bar, click . 2.
User Manual v1.0 5.1.3.7 Activity Log The Activity Log is used to view activities such as configuration changes, according to a range of criteria such as User, Time, Group, etc. The information can be saved in *.csv format (can be opened with MS-Excel). The full log list of all user activities is displayed: The activity log display can be changed in the following ways: "Rows Per Page" can be changed to list a different number of activities per page. Page navigation is at the bottom of the screen.
User Manual v1.0 5.1.4 Multi-Stack Screen MS management allows centralized network management of sites with multiple stacks deployment, sharing common configuration, where user-defined groups of stacks are automatically and immediately updated with common data. MS management allows a main admin (i.e. sysadmin) user to access a single stack GUI and create an MSgroup of up to 100 stacks.
User Manual v1.0 5.1.5 Channels Screen The Channels screen allows the user to create, view and modify the system RF channels. The configuration is done via a map: each map is a group of channels. The system allows storage of two map configurations: one that is currently being used by the system (named VALID map), and another map configuration that may be edited for future use (named INVALID map), where each map determines the configuration of all the system RF channels.
User Manual v1.0 The following table shows the available options for managing the RF channels map: Table 21: Map Options Option When clicking this button the following option appears: Switch between saved maps: invalid map or valid map. Save the map currently loaded in xls format. Load a map from xls file. Create a new map. Add a new RF channel to the map currently loaded. Check validity of the map currently being edited. If the map is successfully validated it will replace the existing valid map.
User Manual v1.0 5.1.5.1 Map Management Flows Below are 2 map management scenarios for example. 1. Create a new map from scratch: Click the button and chose the invalid map Add all required channels using the Click the button to save the map in xls format. The map is not saved as valid or invalid. To continue working on the map use the button to import the xls file. Validate the map using the button button.
User Manual v1.0 2. Change an invalid map and repeat the validation process: Click the button and select the invalid map Modify the map as required: add new channels, delete channels or edit existing channels information. Validate the map using the If there are no errors, map status is and it is saved as the valid map. Any previously saved valid map is lost. button. If there are errors, map status is and the updates are saved to the invalid map. The invalid map no longer exists.
User Manual v1.0 5.1.5.2 Adding a New Channel When choosing the New Channel option, the following form appears: Table 23: Add Channel Form Field Information Cell Id Channel name entered by the user, may include location and other information regarding the channel. DL CF Downlink Center Frequency (MHz). UL CF Uplink Center Frequency (MHz). BW Operator TDD Service Bandwidth (MHz). Name of operator (name of telecommunication company). YES/NO; Indicates whether Time Division Duplexing is enabled.
User Manual v1.0 5.1.5.3 Submitting a map 1. When changes are made to any map the status of the map is "map in process" until the changes are submitted: 2. When the user is done making changes to the map, he can press the "submit" button. Validation of the map begins, and a progress bar appears: The system performs a basic check to make sure all parameters have valid values according to system limits, such as: Number of channels per specific BW, channels overlap, etc.
User Manual v1.0 Progress bar Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 3. A pop up window indicates the activation status. If activation fails, the errors are displayed, as well as the activation status per module. In the following example, the map status is "invalid map" (the map will be saved as the invalid map).
User Manual v1.0 6. SNMP Management The Everon system supports SNMP protocol, which allows standard monitoring via a large variety of 3rd party endpoint monitoring tools, also known as SNMP manager agents (e.g., HP OpenView, CA Unicenter, IBM Tivoli, CastelRock SNMPc): The Everon system sends indications on system events and failures to a userdefined monitoring destination-address, by sending SNMP protocol traps.
User Manual v1.0 6.1 SNMP Setup This section details the following steps, required to set SNMP trap monitoring: 1. Through Everon GUI: set the SNMP protocol version parameters (SNMPv2 / SNMPv3), see 6.1.1 2. Through Everon GUI: Set Traps Monitoring Destination Addresses, see 6.1.2 3. Through your 3rd party SNMP monitoring tool: Load the MIB files, see 6.1.3 6.1.1 Set Protocol Version Parameters (SNMPv2 / SNMPv3) To set SNMP version: 1. Choose Admin from the main menu SNMP Config.
User Manual v1.0 To Configure the SNMPv2 parameters: 1. In the main menu bar, click 2. In the area, click . to change the current configurations. The SNMP Community dialog appears: 3. Select/unselect the checkbox next to "Enable V2" to enable/disable SNMPv2. 4. If necessary, modify the community name in the Community field. 5. Click OK. To configure SNMPv3 parameters 1. In the main menu bar, click 2. Select the required user from the User Name list and click . .
User Manual v1.0 3. Enable "V3" to get the SNMPv3 configuration options: 4. Configure the following SNMPv3 parameters for the user: Authentication protocol MD5/SHA. Privacy protocol None/DES/AES-128. Password one password for both authentication and privacy protocols. 5. Select the internet protocol version (IPv4/IPv6) for the SNMP traps and enter the trap destination address: IPv4 - SNMPv3 trap destination address: IP (x.x.x.x). IPv6 - SNMPv3 trap destination address: IP (0:0:0:0:0:0:0:0). 6.
User Manual v1.0 6.1.2 Set Traps Monitoring Destination Addresses This section explains how to configure the IP addresses to which SNMP traps are sent. Both IPv4 and IPv6 addresses are supported. enables a periodical trap indicating that the device is operational. The trap is sent every user-configured time interval: 1-59 minutes. Note: The defined HB interval must be the same for all devices in the system. This option is disabled by default. To define the trap destination IP address 1.
User Manual v1.0 6.1.3 SNMP manager Setup: Load the MIB File This section describes the steps necessary to view the traps sent by the monitored system in the management application. Note: It is assumed that the HCM IP address and the trap destination addresses have already been configured. To view interpreted traps through the 3rd party management application 1. Start the management application. 2. Load and compile the MIB-II file (a public domain file which can be found on http://www.rfc-editor.org).
User Manual v1.0 No. Binding Description frm = (10) site = (11) mru = (12) lau = (21) och = (24) gx = (25) mxu = (26) 4. trapDeviceSerial Additional data sent with the trap. This is the serial number of the device that generated the trap (up to remote unit level). Chassis serial number of the module 5. trapChassisSN 6. trapChassisIndex 7. trapSlotIndex 8. trapPortIndex 9. trapRemoteIndex 10. trapCtrlSerialNum 11. trapCtrlName Additional data sent with the trap.
User Manual v1.0 6.4 List of traps The system supported traps (i.e. alert messages sent by the system to the SNMP manager, indicating system events or failures), are provided in the following table.
User Manual v1.
User Manual v1.
User Manual v1.0 7.
User Manual v1.0 Radio Interface Frames (IHU/HEU) IHU Chassis Radio Interface Frame Modules RIMe up to 8 modules per chassis DCM up to 2 modules per chassis RIX- one module per chassis OIX - one module per chassis PSM up to 2 modules per chassis dHCM one module per system using IHU and 7 HEU chassis ACM -one module per chassis Single band module (see bands table) Interfaces: UL, DL and duplexed interface ports, QMA RF connectors Weight: 1.9 lbs (0.
User Manual v1.0 Mechanical Dimension (H x W x D) Mounting Weight 58 Lbs (26.4Kg) for full chassis configuration Environmental Operating temperature 0 to +50° C (32 to 122° F) *Technical spec subject to change without notice Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 HEU Chassis Radio Interface Frame Modules RIMe up to 12 modules per chassis RIX- one module per chassis PSM up to 2 modules per chassis ACM -one module per chassis Single band module (see bands table) Interfaces: UL, DL and duplexed interface ports, QMA RF connectors Weight: 1.9 lbs (0.9 kg) Interfaces: Two 9-pin coaxial interface connectors (RF and Clock) Two QMA ports for reference clock connections between Radio Interface Frames (IHU, HEU) Weight: 1.54 lbs (0.
User Manual v1.0 Mechanical Dimension (H x W x D) Mounting Weight 64.5 Lbs (29.3) for full chassis configuration Environmental Operating temperature 0 to +50° C (32 to 122° F) *Technical spec subject to change without notice Corning Restricted and Confidential Proprietary - Controlled content UM - Everon 6000 DAS - 19-DEC-2020.
User Manual v1.0 DRU - Digital Routing Unit Interfaces & Mechanical CPRI ports CPRI ports Ethernet Ports External synchronization Mounting: Dimension (W x H x D) Weight 32 x SFP+ (10.1 Gbps, CPRI line bit rate option 8) to Remote Units 4 x SFP+ (10.1 Gbps, CPRI line bit rate option 8) to DCM 2x RJ45 - LAN, Local 2*QMA -10MHz In/Out 19.
User Manual v1.0 Low Band LRU-Low power Remote Unit End to End System Performance Headend to Digital Low power Remote Unit RF Specifications Frequency Range Name Uplink Downlink Max.
User Manual v1.0 Medium Band LRU- Low power Remote Unit End to End System Performance Headend to Digital Low power Remote Unit RF Frequency Range Name Uplink Frequency Range Downlink Max.
User Manual v1.0 LRU 2:2 MIMO Antenna Combiner The LRU combiner is used to combine the 2 LRU Low Band LRU and Medium Band LRU. The combiner has a total of 6 input ports and 2 output ports. There are two independent three-frequency combiners inside.
User Manual v1.0 MRU - Medium Power Remote Unit System performance Head End to Medium power Remote Unit RF Frequency Range Name 600 Uplink Frequency Range MHz Downlink 663698 617652 700L & 700U & FirstNet 698- 777716 798 728- 746746 768 Max.
User Manual v1.0 Interfaces and Mechanical CPRI Port Antenna Ports CBRS port Coupling port Dimension (W x H x D) Mounting and installation Weight Cooling Inch (mm) Lbs (Kg) 2, SFP+ 10.1Gbps 1, 4.3-10 female 1, N-Type female 1 ,QMA connector that will enable measurement of the DL/UL signals while the system is working 17.45 x 10.5 x 15.75 (443.2 x 266.7 x 400) -Wall mount and Rack mount options 83.
User Manual v1.0 HRU -High-Power Remote Unit System performance (Head End to High power Remote Unit) RF Frequency Range Name 600 Uplink Frequency Range MHz Downlink Max.
User Manual v1.0 Interfaces and Mechanical CPRI Port Antenna Ports Dimension (W x H x D) 4, SFP+ 10.1Gbps 1 ,4.3-10 female OEU Inch (mm) RFU except 700 RFU 700 Mounting and installation Weight Lbs (Kg) Cooling Wall mount OEU RFU except 700 RFU 700 Convection 14.6 x 3.2 x 13.8 (370 x 80 x 355) 19.7 x 3.2 x 13.8 (500 x80 x355) 19.7 x4.8 x 13.8 (500 x121 x355) 26.4 (12) 39.
User Manual v1.0 Medium Bands Combiner specifications The medium band combiner is designed to combine the following services: 1900, EAWS, WCS and 2.5GHz. If a single module is required a single input (2500) is used. If 2 * 2.5GHz RF modules are used (to support 4G and 5G services) 2 inputs are required (2500 IN1 and 2500 IN2) .
User Manual v1.0 8. Ordering information | Headend Unit Assemblies and RF Modules HEU Assemblies Part Number Description HEU: Head End Unit Assembly (without RIMe); provided with ERFC, one PSM and one RIX Hosts one RIX module; one ETM. one PSM-AC and one ACM Hosts one RIX module; one ETM.
User Manual v1.0 Integrated Headend Unit Assemblies Note: IHUs support both RIMe and OIMs (ordering information detailed in HEU and OIU ordering information).
User Manual v1.
User Manual v1.
User Manual v1.
