User's Manual

ManualsBrandsCoreTigo ManualsElectronicsIO Link wireless 2.4G band transceiver module

TigoBridge User Manual

Page 1 of 16

CoreTigo®

TigoBridge Manual

Revision 2.0

April 1, 2020

Summary of content (16 pages)

PAGE 2
TigoBridge User Manual Table of Contents 1 2 3 Introduction ............................................................................................................................... 4 Safety instructions ..................................................................................................................... 4 Overview ................................................................................................................................... 5 3.1 Functional Diagram ..............
PAGE 3
TigoBridge User Manual Table of Tables Table 1 - Revision control................................................................................................................. 3 Table 2 - Acronyms and Abbreviations ............................................................................................ 3 Table 3 - Power LED ........................................................................................................................ 7 Table 4 - Status LED...................................
PAGE 4
TigoBridge User Manual 1 Introduction This document presents CoreTigo IO-Link Wireless Bridge. This manual will introduce you to the TigoBridge, learn how to use the TigoBridge & understand its indications. Please read the manual very carefully before starting to use the device. Figure 1 - TigoBridge 2 Safety instructions • • • • • Page 4 of 16 Read this document before setting up the product and keep it during the entire service life.
PAGE 5
TigoBridge User Manual 3 Overview The TigoBridge is an IO-Link Wireless Class A Bridge with IP67 Enclosure. The TigoBridge converts IO-Link to IO-Link Wireless. The TigoBridge houses internal antenna and two M12 connectors for data and power. TigoBridge is a device that connects a wired IO-Link device via IO-Link Wireless to an IOLink Wireless Master/Gateway. B C A D E Figure 2 - TigoBridge Overview A. B. C. D. E.
PAGE 6
TigoBridge User Manual 3.1 Functional Diagram A C B D E Figure 3 - TigoBridge functional diagram A. B. C. D. E. Device Connection Paring Button Power Supply Connection Status LED (RGB) Power LED (Green) A B E 123456789 12:34:56:78:9A:BC:DE:F1:23 C F D G Figure 4 - TigoBridge Label Label A. Model Number B. Product Number C. Serial Number (Sticker) D. UID – TigoBridge UID Code, UID QR Code and UID Barcode (Stickers) E. Input Power Supply Range F. TigoBridge Pin-Out G.
PAGE 7
TigoBridge User Manual 3.2 LEDS B A Figure 5 - TigoBridge LED View A. Power LED (Green) B. Status LED (RGB) 3.2.1 Power LED LED Color Green Indication Power supply connected Table 3 - Power LED 3.2.2 Status LED LED Color Magenta Blue Green Yellow White Blinking Green Indication Unpaired wireless Paired wireless Operational wired device Non-operational wired device Wireless Error1 Firmware update mode Table 4 - Status LED 3.
PAGE 8
TigoBridge User Manual 3.4 Electrical Wiring TigoBridge has two M12 connectors. - IO-Link connector: 5 pins, female connector. Temperature range: -40C° - +85C°. Note: Maximum Current supply to IO-Link device is 1A when using 24VDC. - Power connector: 5 pins, male connector. Temperature range: -40C° - +85C°. Note: Higher voltage than 32VDC might damage the TigoBridge. Figure 6 - Electrical Schematic Diagram Page 8 of 16 Copyright © 2020 CoreTigo Ltd.
PAGE 9
TigoBridge User Manual 4 Mounting 4.1 Cradle TigoBridge should be mounted safely next to the device. The cradle designed to help mount the TigoBridge on flanges. Cradle can be mounted to the flange/wall using cable ties or M3 screws. Figure 7 - Cradle Dimensions Figure 8 - TigoBridge and Cradle Page 9 of 16 Figure 9 - TigoBridge mounted on the cradle Copyright © 2020 CoreTigo Ltd.
PAGE 10
TigoBridge User Manual 4.2 Mounting the TigoBridge - TigoBridge can be mounted using the cradle on a flange. Secure the cradle location on the flange using M3 screws. Mount the TigoBridge on the cradle by pushing it in. Unmounting is done by pulling the TigoBridge from the cradle. 5 Configuration & Setup Pre-Commissioning Requirements: - TigoEngine software installed and running on the working PC. TigoMaster/TigoGateway successfully connected to PC. Installation: 1.
PAGE 11
TigoBridge User Manual 7. Identify the TigoBridge using the UID. Select the requested TigoBridge[1]. Select an empty port on the master side[2] and press “Pair”[3]. 3 1 2 Figure 11 - TigoEngine Pairing Process 8. Once the pairing process done successfully, TigoEngine “Port Mode” should indicate “OPERATE”. TigoBridge Status LED will alternate between blue and green. Connection successfully established. Configuring the IO-Link device can be done through the DATA tab.
PAGE 13
TigoBridge User Manual 7 Diagnostics and Troubleshooting Troubleshooting can be done using the LEDs display or the TigoEngine software. 7.1 Power LED Power LED – if power supply connected to TigoBridge and Power LED is off, power supply is not properly connected or different than the expected power supply range. If power cycle does not help, contact CoreTigo support. 7.
PAGE 14
TigoBridge User Manual 8 Guidelines and Regulations FCC ID: 2ATSM-TGBRIDGEA1 8.1 RF Exposure Warnings RF Exposure Warnings This device is only authorized for use in a mobile application. At least 20 cm of separation distance between the (Product Name) device and the user's body must be maintained at all times. 8.2 Class A Warning The FCC Wants You to Know This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
PAGE 15
TigoBridge User Manual 9 Appendix IO-Link Wireless Masters Alternatives: All masters are designed to communicate with IO-Link Wireless devices. However, each Master/Gateway has its own IT/OT communication features. TigoMaster/ TigoGateway TigoMaster 2TS Image Description IO-Link Wireless Master designed with USB connection. TigoMaster 2TH IO-Link Wireless Master designed to communicate both with IT and OT networks. Supports both OPC-UA, MQTT and Industrial Ethernet & Fieldbus protocols.