C-One2 Quick Start and Regulatory Guide QSG 180190 A30 | Non-Contractual Pictures |
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 WHAT'S IN THE BOX ? C-One2 HF ASK C-One2 HF iClass | LF Prox C-One2 HF LEGIC | LF TM C-One2 LF Agrident OR 2 1 4 6 3 5 8 7 9 1 DEVICE 4 HANDSTRAP 7 PLUG | EUROPE 2 NOTICE 5 CABLE MICRO USB | USB A 8 POWER SUPPLY 3 BOX 6 STYLUS 9 TEST REPORT Page 2 | 15
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 PRODUCT OVERVIEW programmable key | scan key (P2) C-One2 HF ASK 2D imager C-One2 HF iClass | LF Prox led indicators C-One2 HF LEGIC | LF TM microphon e handstrap holder volume keys +/speake r receiver flash camera RFID antenna power key programmable key (P3) programmable key | scan key (P1) 4.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Setting up your device CAUTION Failure to completely reseal the Micro SD | Micro SIM card slot cover may lead to water or other liquids entering the casing which may cause damage to the device. MICRO SIM card installation • Open Micro SD | Micro SIM door. • To remove the Micro SIM card: Insert a removal tool (pin type) into the hole then push until the tray pops out. • Put the Micro SIM card on the tray. • Insert Micro SIM tray into SIM slot.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Setting up your device CAUTION Do not use internal peripherals during charging process. Please make sure the device being charged fully when using C-One² at first time. Please ensure the Micro USB port clean and dry before inserting a USB cable for charging to avoid the operating issues on the device. Please remove water or moisture from the Micro USB port instantly with soft cloth when the device gets wet, to avoid the operating issues on the device.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Setting up your device LED indicators LED1 LED2 Red LED blinks (LED1) Low battery Red LED (LED1) Battery is charging Green LED (LED1) Battery is fully charged Blue LED blinks (LED2) BT devices connected or receiving messages/notifications Page 6 | 15
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Using your device TURNING ON | TURNING OFF your device Power Off | Press and hold during 5 sec. the power button and select “Power off” in the dialog box. Reboot | Press and hold during 5 sec. the power button and select “Reboot” in the dialog window to restart the device. Suspend Mode | Press and release the power button to place the device in suspend mode. The display will be off and go into a low power state to conserve battery power.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Using your device DATA CAPTURE | photos & videos Use the rear camera to take photos and capture video. 1. Go to Home Screen > select “Camera” > Tap camera icon or screen to take a picture/switch to video icon and tap for video recording. 2. Using the rear camera to take photos and capture video. NOTE Ensure device memory or extend Micro SD card space is available. DATA CAPTURE | barcode scanner CAUTION Class 2 laser when open.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Using your device RFID C-One2 HF ASK - C-One2 HF iClass | LF Prox - C-One2 HF LEGIC | LF TM with RFID options to read, please put the TAG/CARD on the RFID area. RFID READING AREA C-One2 LF AGRIDENT with RFID options to read, please put the TAG/CARD on the RFID area.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Regulatory information CAUTION Only use COPPERNIC approved accessories.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Wireless Device Country Approval CAUTION Operation of the device without regulatory approval is illegal. Regulatory markings, subject to certification, are applied to the device signifying the radio(s) are approved for use in the European countries under CE coverage. For 2.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Power Adaptor Use only a C-One² approved Power Adaptor with electrical ratings: Output 5VDC, min 2A, with a maximum ambient temperature of at least 45°C. Use of alternative power adaptor will invalidate any approvals given to this device and maybe dangerous. Battery Information Use only a COPPERNIC approved batteries. When devices are stored over six (6) months without use, some irreversible deterioration in overall battery quality may occur.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 FCC INFORMATION TO USERS Radiation Exposure Compliance This product complies with the FCC RF exposure limits for an uncontrolled environment. FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
C-One2 Quick Start and Regulatory Guide QSG 180190 A30 Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components.
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. (3)indoor use only 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is 0.
for typical body-worn operations. To comply with RF exposurerequirements, a minimum separation distance of 10mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.