MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.
ENGLISH MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.qxd 8/28/08 11:18 AM Page 2 MS275RD (Bronze) MS275RDW (White) Congratulations. You have just purchased a Cooper Lighting, LLC motionactivated floodlight that combines both Precision Plus Doppler Radar™ and PIR (Passive Infrared) technology. This combination provides the maximum accuracy and protection for your home and family. How it works PIR does a good job of detecting lateral motion across the 270° range of detection.
MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.qxd 8/28/08 11:18 AM Page 3 WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authorization to operate this equipment. SAVE THESE INSTRUCTIONS. For best results • Install the motion sensor/transmitter 8-12 feet above ground (motion sensor is less sensitive above 12 feet).
MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.qxd 8/28/08 11:19 AM Page 4 ENGLISH • Locate motion sensor so motion moves laterally or towards the detection zone (Fig. 1). • Locate sensor away from heat producing sources to prevent false triggering. Also, be very careful not to include objects such as windows, white walls and water in the detection zone whenever possible. • Locate sensor away from moving objects such as trees and street traffic.
MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.qxd 8/28/08 11:19 AM Page 5 Aiming the light WARNING: Deviation from the assembly instructions may result in a risk of electric shock. How to operate your fixture Step 1: Turn the arrow on the MODE knob to the TEST for test mode (Fig. 5). Step 2: Turn the arrow on the SENSITIVITY knob to a middle point between “+” and “-”. Step 3: Turn on the power to the fixture. Allow fixture to warm up approximately 90 seconds before testing.
MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.qxd 8/28/08 11:19 AM Page 6 ENGLISH Selecting your mode of operation Mode of Operation: MODE Knob Adjustment: How to Set Power Switch: Test Setting MODE knob arrow points to TEST Wall Switch Setting (connected to fixture) Light should turn ON with motion both day and night. Lights should turn OFF after 2 seconds. Motion-Activated Setting Lights should turn ON with motion only at night and should turn OFF after 1-12 min.
MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.qxd 8/28/08 11:19 AM Page 7 What to do if . . . Is there power to the fixture? • Check to see that the circuit breaker has not been tripped. • Be sure the wall switch is in the ON position. • Be sure that the bulbs are not burned out or broken. Is the surrounding external ambient light too bright? (If so, the unit may think it’s daytime.) • Re-aim the head. • Relocate or reposition the unit away from the light. TURN OFF POWER BEFORE CONTINUING.
MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.qxd 8/28/08 11:19 AM Page 8 ENGLISH Two-year limited warranty Cooper Lighting, LLC (“the Company”) warrants this product (“the product”) against defects in material or workmanship for a period of two years from date of original purchase, and agrees to repair or, at the Company’s option, replace a defective product without charge for either replacement parts or labor during such time. This does not include labor to remove or install fixtures.
MS275RD_RDW 825-0133.qxd:RFM181 I.S. 325-1384.qxd 8/28/08 11:19 AM Page 9 ENGLISH Customer First Center 1121 Highway 74 South, Peachtree City, GA 30269 www.cooperlighting.com © 2008 Cooper Lighting, LLC Reproductions of this document without prior written approval of Cooper Lighting, LLC are strictly prohibited.