XPD900 User Manual Revision 1.2 Michael Bazzarelli This document, submitted in confidence, contains proprietary information which shall not be reproduced or transferred to other documents, disclosed to others, used for manufacturing or any other purpose without the prior written permission of Eaton / Cooper Industries (Electrical) Inc. Copyright 2021 Eaton / Cooper Industries (Electrical) Inc. All rights reserved.
XPD900 User Manual Revision 1.2 Revision History Revision 1 1.
XPD900 User Manual Revision 1.2 Table of Contents 1 Introduction .......................................................................................................................................... 4 2 List of Applicable FCC and ISED Rules ................................................................................................... 4 3 Specific Operational Use Conditions .....................................................................................................
XPD900 User Manual Revision 1.2 1 Introduction The XPD900 transceiver module is not sold as a stand-alone device. The XPD900 module is a subassembly intended for use inside Eaton host products. This manual provides information regarding the integration of the module with host products. The XPD900 radio module has been certified for the FCC and ISED as a portable single-modular transmitter. The XPD900 PCB revision 5 radio module has the FCC ID: IA9XPD900A and the ISED certification number: 1338B-XPD900A.
XPD900 User Manual Revision 1.2 6 RF Exposure Considerations The XPD900 radio module and antenna must be physically located such that SAR limits are not exceeded. Several antennas were tested with the radio module and a test report was created that provides the calculated distance requirements that must be maintained between the radio antenna and the user. For portable module certification the test report, “E10788-2103_Cooper Electrical_XPD900_RF_Exposure_Rev 1.0.
XPD900 User Manual Revision 1.2 product SMT antenna, and host product dipole antennas were evaluated and require different minimum separation distances between the user and the radiating element. RF Exposure Statement To comply with FCC and ISED RF exposure requirements, installation of this transmitter system’s antenna must be performed in a manner that will provide the appropriate distance from the antenna to any user or member of the public.
XPD900 User Manual Revision 1.2 7.2 ISED Statement In accordance with the requirement of RSS-GEN 8.4, the following statement shall be included in the user manual. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2.
XPD900 User Manual Antenna Part Number Center Frequency (MHz) Dimensions Connection Bandwidth (MHz) Wavelength VSWR Peak Gain (dBi) Impedance (Ω) Revision 1.2 1 AKIT-3591-04 914.9 Maximum height 13.5" SMA 70 Collinear Array 5/8λ over 1/2λ 2:1 5.4 50 2 AKIT-3591-07 914.9 3.1 X 1.496" SMA 262 1/4λ monopole 3.3:1 3.52 50 Notes Host Devices Tested R260 R7, R260 R13, R270 R3 R260 R7, R260 R13, R270 R3 3 A0042 916 0.5 x 0.36" Surface mount 25 1/4λ monopole ≤ 2.0 typical at centre 2.
XPD900 User Manual Antenna Host Product Revision Part Number 1 R260 7 FPCB-3375R07 2 R260 7 FPCB-3375R07 4 R260 7 FPCB-3375R07 1 R260 13 FPCB-3375R13 2 R260 13 FPCB-3375R13 4 R260 13 FPCB-3375R13 1 R270 3 FPCB-3958R03 2 R270 3 FPCB-3958R03 4 R270 3 FPCB-3958R03 3 TD3100 4 FPCB-3875R04 3 TD2100 3 FPCB-4014R03 3 TD1141 2 FPCB-4053R02 Revision 1.
XPD900 User Manual Revision 1.2 When testing for unintentional radiator of the host product, the transmitters shall be placed in the receive or idle mode. If that isn’t possible the radio should be passive (preferred) and/or active scanning, and thus not turned off. In addition, the host product should be setup to ensure there is activity on the communications BUS of the product (e.g. USB, CAN bus, GPIO) to ensure unintentional radiator circuitry is enabled.
