User's Guide

Quick Start Guide
On-Screen Indicators
Get Updates
Get updates, user guides and more information for your Coolpad Stream Mobile Hotspot
at www.coolpad.us. Discover what’s going on right now in hotspot news, trends,
techniques & other cool stuff by connecting with us by:
@CoolpadAmericas
Trademarks and Copyrights
©2021 Coolpad Technologies Inc. Coolpad
®
and Coolpad Stream
TM
are trademarks of
Yulong Computer Telecommunication Scientific (Shenzhen) Co., Ltd. All Rights Reserved.
Google and Android are trademarks of Google Inc. Other trademarks and trade names are
the property of their respective owners. Screenshots and product images are simulated;
they may differ from the actual product and are subject to change. Reproduction,
transfer, distribution of the contents herein in any manner without the prior written
permission of Coolpad Technologies, Inc. is prohibited. Coolpad Technologies, Inc.
reserves the right to add, modify or delete, any of the contents herein or withdraw this
documents at any time without prior notice and without assigning any reasons thereof.
Getting to Know Your Mobile Hotspot
Hold the Power key for 3 seconds to power the device on/off.
Hold the WPS key for 3 seconds to activate the WPS function. Once
activated, the Wi-Fi
TM
LED indicator will blink every two seconds. If
the network is not accessed within 2 minutes, the device will
automatically exit WPS (Wi-Fi Protected Setup) mode.
Display network signal, Wi-Fi, SMS, battery charge and mobile data
status.
Use the USB port to charge your device via the USB cable.
Hold both the Power key and the WPS key simultaneously for 15
seconds. All LED indicators will blink green 4 times to indicate that
the device has been reset to factory default settings.
Hold the Power key for 32 seconds to restart it when the device
becomes unresponsive.
Power key:
WPS key:
LED indicators:
USB port:
Reset:
Reboot:
Displays your current network status. Solid green light indicates
strong network signals; solid yellow light indicates normal network
signals; solid red light indicates no network or weak network
signals, no SIM or bad SIM card, limited or no service.
Solid green light indicates Wi-Fi is active. Blinking green light
indicates WPS mode is active.
Indicates when there is a new message (not applicable).
Displays your current battery status. Solid green light indicates the
battery level is more than 39%, solid yellow light indicates the
battery level is 16%-39%, and solid red light indicates the battery
level is less than 16%; when the device is charging, the indicator will
blink red when the battery level is at or below 16%, will blink yellow
when the battery level is 16%-39%, and will blink green when the
battery level is more than 39%.
Blinking red lightindicates less than 26% monthly Data left, blinking
yellow lightindicates 26%-50% monthly Data left, blinkinggreen
light indicatesmore than 50% monthly Data left. 
Network:
Wi-Fi:
SMS:
Battery:
Data:
1.
2.
3.
1.
2.
3.
4.
5.
1.
2.
3.
Charging Your Mobile Hotspot
Connect the USB-C end of the USB cable to the USB port on your device.
Connect the other end to the travel adapter.
Connect the travel adapter to an electrical outlet to fully charge your device.
Note: You can also charge the device by connecting it to a computer with the USB cable.
Connecting Your Wi-Fi Device to Your Mobile Hotspot
Power on your mobile hotspot.
On your computer or other Wi-Fi enabled device, search for available Wi-Fi networks
and select network name (SSID) located on label on back panel of your mobile
hotspot.
Note: Wi-Fi name (SSID) and Wi-Fi Password are located on the label inside the back
cover of the device.
From a Windows computer: Left-click Wireless Network Connection on the task
bar to view available networks. Choose the SSID from the list of available networks.
From a Mac computer: Select System Preferences > Network. Choose the SSID
from the list of available networks.
From an iOS device: Go to Settings > Wi-Fi. Choose the SSID from the list of
available networks.
From an Android device: Go to Settings > Wi-Fi. Choose the SSID from the list of
available networks.
Enter the password located on label on back panel and click OK.
Using the WPS
If your Wi-Fi device supports WPS, you do not have to input the password manually after
a WPS connection has been established. Please follow the following steps:
Power on your Mobile Hotspot and enable the Wi-Fi function from the device you
would like to connect.
Press and hold the WPS key on your device for 3 seconds to start the Wi-Fi
Protected Setup authentication process.
Enable the WPS function on your Wi-Fi device in order to respond to this
authentication process.
Follow the system prompts on your Wi-Fi device to finish the connection.
If no Wi-Fi device is connected within 2 minutes, the WPS function will automatically
turn off.
Managing Your Mobile Hotspot
You can access your Mobile Hotspot device information using an Internet browser or by
connecting the device to a computer via the USB cable.
Setting Up Your Mobile Hotspot
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
5.
Access Mobile Hotspot Using A Browser
Connect to your hotspot device through Wi-Fi using the network connection
software on your computer. Provide the Wi-Fi network password, if requested.
Open a browser and enter http://mobile.hotspot or http://192.168.0.1 in the
address bar. The Coolpad Stream Mobile Hotspot Web User Interface screen will
appear.
Click Login on the top right of the Web UI screen. The login screen will appear.
Enter your Password in the field provided. The default password is "admin".
Click Login. If you entered the correct password, the Web User Interface screen
appears again.
Access Mobile Hotspot Using USB Cable
Connect your Coolpad Stream Mobile Hotspot to the computer with the USB cable.
Power on your device.
The computer operating system detects and recognizes new hardware and finishes
the installation automatically.
Open a browser and enter http://mobile.hotspot or http://192.168.0.1 in the
address bar. The Coolpad Stream Mobile Hotspot Web User Interface screen will
appear.
Click Login on the top right of the Web UI screen. The login screen will appear.
Enter your Password in the field provided. The default password is "admin".
Click Login. If you entered the correct password, the Web User Interface screen
appears again.
Note: Windows (32 bit & 64 bit) 7/8/8.1/10, Mac OS X 10.6 to 10.11 supported.
Changing Mobile Hotspot Admin Password
Access http://mobile.hotspot or http://192.168.0.1.
Click Settings in the navigation area.
Select the Device tab and click Account Management.
Follow steps under Account Management to update your Password.
Click Save Changes. If everything is entered correctly, the Success message will
appear indicating the password was successfully changed.
1.
2.
3.
4.
5.
6.
Changing Mobile Hotspot Network Name (SSID)
Access http://mobile.hotspot or http://192.168.0.1.
Click Settings in the navigation area.
Select the Wi-Fi tab and click Basic.
Enter a new name in the Wi-Fi Name (SSID) field.
Click On or Off checkbox for Hide SSID to disable or enable broadcasting the
hotspot’s Network Name (SSID).
Click Save Changes.
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
1.
2.
1.
2.
3.
Changing Mobile Hotspot Wi-Fi Password
Access http://mobile.hotspot or http://192.168.0.1.
Click Settings in the navigation area.
Select the Wi-Fi tab and click Basic.
Select WPA2 for the Authentication Method.
Enter a new password in the Wi-Fi Password field.
Click Save Changes.
Changing Mobile Hotspot’s Access Status
When the Access Status “Allow all devices to access with password” is selected, users
will be allowed to access to network via use of correct password. When the Access
Status “Allow only users on Permitted list” is selected, only users that have been
granted access by adding a user’s MAC address will be able to connect to the network.
Log into the Web User Interface.
Go to Connected Devices > Access Permissions. The Access Status “Allow only
users on Permitted list” is selected by default. Any user who inputs the correct
password can access the network.
Select “Allow only users on Permitted list” and click Add.
Enter the device name and the MAC address, and click Apply to add a user to the
Permitted Device List.
Click Save Changes.
Note: If you remove a user from the Permitted Device List, such user will no longer be
allowed to connect to the network. Click Delete to remove.
Updating Software Version
Check the software version currently installed on your mobile hotspot.
Access http://mobile.hotspot or http://192.168.0.1.
Within the Web User Interface, go to About > Firmware > Firmware Version to view
which software version is currently installed on your device.
Update your mobile hotspot to the most up-to-date software version.
Access http://mobile.hotspot or http://192.168.0.1.
Within the Web User Interface, go to Settings > Device > Software Updates.
Click Update Firmware to update.
Note: Do not remove the battery during software updating. This may cause the software
update to fail.
Hello from Coolpad
Thank you for purchasing your Coolpad Stream Mobile Hotspot! Please follow these
simple but important instructions for optimal use of your new mobile hotspot.
1. Remove the battery cover.
Lift gently in the direction shown.
3. Attach the battery cover.
Make sure all the tabs are secure
and there are no gaps around the
cover.
2. Insert the battery.
Align the contacts of the battery
with the contacts in the hotspot.