Manualshelf

Installation Guide

ManualsBrandsCoolaroo ManualsWindow ShadesChesnut Light Filtering Cordless High-density Polyethylene Exterior Shade (Common: 72-in x 72-in; Actual: 72-in x 72-in)
123456
Easy Release
with Full Valance
10-minute set up
(approximate time)
(3) Bracket Covers
(6) Tie Downs
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(3) Bracket Covers
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(4) Wand
(3) Bracket Covers
(5) Bottom
Rail Cap
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(3) Wand
(4) Bottom
Rail Cap
(6) Bottom Rail
(7) Shade
(8) Idle End
Unit
(9) Idle End Plug
(10) Aluminum Tube
(2) Clutch Plug
(3) Wand
(4) Bottom
Rail Cap
(6) Bottom Rail
(1) Shade
(8) Idle End
Unit
(9) Idle End Plug
(10) Aluminum Tube
(2) Bottom
Rail Caps
with rings
(4) Bottom Rail
(1) Full Valance
(5) Receiver
(3) Bungee
(6) Wood
Screws
(7) Brackets
(9) Tension
adjustment
tool
(10) sola panel
(11) mounting
bracket
(12) solar panel clip
(13) screw
(14) nut screw
(8) Anchors
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(4) Chain
(5) Bottom
Rail Cap
(2) Clutch Plug
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(4) Chain
(5) Bottom
Rail Cap
(3) Bracket Covers
(6) Tie Downs
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(3) Bracket Covers
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(4) Wand
(3) Bracket Covers
(5) Bottom
Rail Cap
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(3) Wand
(4) Bottom
Rail Cap
(6) Bottom Rail
(7) Shade
(8) Idle End
Unit
(9) Idle End Plug
(10) Aluminum Tube
(2) Clutch Plug
(3) Wand
(4) Bottom
Rail Cap
(6) Bottom Rail
(1) Shade
(8) Idle End
Unit
(9) Idle End Plug
(10) Aluminum Tube
(2) Bottom
Rail Caps
with rings
(4) Bottom Rail
(1) Full Valance
(5) Receiver
(3) Bungee
(6) Wood
Screws
(7) Brackets
(9) Tension
adjustment
tool
(10) sola panel
(11) mounting
bracket
(12) solar panel clip
(13) screw
(14) nut screw
(8) Anchors
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(4) Chain
(5) Bottom
Rail Cap
(2) Clutch Plug
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(4) Chain
(5) Bottom
Rail Cap
Outdoor Roller Shade
INSTALLATION
INSTRUCTIONS
DETERMINE DESIRED MOUNTING METHOD
This two-in-one valance design allows you to easily mount the sun shade to either a
ceiling (Fig. 1) or a wall (Fig. 2).
For ease and flexibility in mounting divide your shade into three even zones, the three
quick-connect brackets can be positioned anywhere inside each of these three zones.
Be sure to keep each of the three brackets inside these zones for proper balance and
weight distribution of the valance.
WARNING: If you do not ensure the quick mount brackets are positioned
with the release button in the correct direction (Fig. 4 and Fig. 5), removing
the shade may be difficult. The brackets must be positioned and installed level
to ensure the shade hangs level and functions properly.
OR
Fig. 1 Fig. 2
Fig. 4
Fig. 5
NOTE: If installing to a ceiling (Fig. 4) ensure the tab on
the bracket facing towards you. If installing to a wall (Fig. 5)
ensure that the tab on the bracket is facing downward.
Allow at least 5.08 cm (2 in) of clearance between the
bracket and wall or ceiling to allow space to snap shade
onto bracket.
If brackets are installed upside down or backwards, the
blind WILL NOT FIT.
ADDITIONAL TOOLS NEEDED
Drill with 3/16 in bit
Level
Tape Measure
Pencil
Tabs forward
Ceiling mount
Wall mount
Tabs downward
PARTS LIST PARTS QTY
1 Full valance 1
2 Bottom rail caps with rings 11-BRC 2
3 Bungee 11-BUNGEE TD 2
4 Bottom rail 1
5 Receiver 1-RECEIVER 2
6 Wood Screws 4-WS 10
7 Brackets Z-14-FCIBW 3
8 Anchors 10
9 Tension adjustment tool 1
INSTALL QUICK CONNECT BRACKETS AND SUN SHADE
IMPORTANT: The screws included in your hardware kit are for use with
wood only. Call Customer Service (1-800-560-4667) for mounting
recommendations when attaching your shade to any other material.
A. In the desired locations, attach Quick Connect Brackets (Fig. 3) with screws,
into wooden stud.
B. Install the Shade by snapping the unit securely into place.
Fig. 3
This side goes on
mounting surface
2
(3) Bracket Covers
(6) Tie Downs
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(3) Bracket Covers
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(4) Wand
(3) Bracket Covers
(5) Bottom
Rail Cap
(7) Bottom Rail
(8) Shade
(9) Idle End
Unit
(10) Idle End Plug
(11) Aluminum Tube
(3) Wand
(4) Bottom
Rail Cap
(6) Bottom Rail
(7) Shade
(8) Idle End
Unit
(9) Idle End Plug
(10) Aluminum Tube
(2) Clutch Plug
(3) Wand
(4) Bottom
Rail Cap
(6) Bottom Rail
(1) Shade
(8) Idle End
Unit
(9) Idle End Plug
(10) Aluminum Tube
(2) Bottom
Rail Caps
with rings
(4) Bottom Rail
(1) Full Valance
(5) Receiver
(3) Bungee
(6) Wood
Screws
(7) Brackets
(9) Tension
adjustment
tool
(10) sola panel
(11) mounting
bracket
(12) solar panel clip
(13) screw
(14) nut screw
(8) Anchors
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(4) Chain
(5) Bottom
Rail Cap
(2) Clutch Plug
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(2) Clutch Plug
(1) Clutch Unit
(4) Chain
(5) Bottom
Rail Cap
1

Summary of content (6 pages)