NUVENIO NV HD User’s Guide Digital Satellite Receiver
Before Getting Started Information contained in this manual is subject to change without notice. No part of this publication may be copied, reproduced, or translated to another language for any purpose. y y y y y y y y Be sure to read the user manual before starting the operation of the receiver. Do not open the housing. The receiver contains high-voltage components and parts. Even after switching off the receiver still contains high-voltage for a while. Do not expose to rain or moisture.
Contens 1. Before Getting Started··································································································1 1.1 Main Features ······································································································· 1 1.2 Accessories ···········································································································2 2. Controls and Functions ······························································································3 2.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Main Features 1.1 Main Features . Easy Menu Function . TV Guide Function . RF Output Function . Electronic Program Guide(EPG) for On Screen Channel Information . Software Upgrading Function through RS-232C Cable by PC / USB STICK . Perfect DiSEqC 1.0, DiSEqC 1.2, USALS for Various Antenna Systems . Supports of Ku/C band, SCPC and MCPC . Additional Audio Output Function for Connection to Hi-Fi Audio System .
Accessories 1.
Controls and Functions 2.1 Front panel Turn the power on/off. MENU Shows the menu application. OK Select menu or value on menu item. VOL◀▶ Control volume, change item on menu or input frequency value. CH▼▲ Change channel, move menu, or input frequency value.
Rear Panel 2.2 Rear panel ATSC INPUT The signal supplied to this connector from a TV antenna will be sent to TV antenna output. Connect a TV antenna to TV ANT IN. LOOP OUTPUT It provides Composite video. Connect the TV scart on TV to TV. S-VIDEO Separate Video, better picture quality than Composite. LNB IN It receives signals from the LNB in the range of 950 ~ 2150MHz. Connect a satellite dish to DIGITAL SATELLITE RECEIVER. IF OUT It sends signal to another receiver.
Controls and Functions ON / OFF The switch is to turn on or off the main power of the receiver mechanically.
Remote Control Unit 2.3 Remote Control Unit Open the controller cover on the back and insert two batteries (AAA - 1.5V). POWER Turn the power on/off. MUTE Deactivate current sound. Numeric(0~9) Change channel or input frequency value. TV/SAT Select between TV Channels and Satellite channels for RF output. RECALL It is to move to previous channel. GUIDE Shows EPG [ELECTRONIC PROGRAM GUIDE.
Controls and Functions Favorite Channels or Edit TV(Radio) Channels. TV Change to TV mode from radio channel. RADIO It is for fast change to radio mode from TV channel. Shows the current Radio program list. ZOOM 2 times zoom in mode. First press, show target area box. Second press, show zoomed screen. Zoom area can be moved with with arrow keys. Exit zoom in mode with “EXIT” remote key.
Connections 3.1 Connecting to the TV, VCR and Satellite Antenna It is not necessary to adjust power, as the product is of free - voltage (AC 110~220V ) 1. Connect another scart cable from the TV on the satellite receiver to scart socket on the TV. 2. Connect the RF cable from the TV OUT on the satellite receiver to a TV. Connect an antenna to the LNB socket on the VCR or other receiver and the RF modulate on the VCR and the TV ANT.IN. 3.
Connections 3.3 Connecting to the TV, HiFi system 1. Connect the RCA cable from the VIDEO INPUT on the TV to the VIDEO on the satellite receiver. 2. Connect a RCA stereo cable from the AUDIO RL on the satellite receiver to the AUDIO RL on the HiFi system. 3.4 Connecting Smart Card module (Optional) To receive the distributed program of Service Provider you need a Smart card Insert smart card slot for watching TV programs from Service Provider.
Antenna Setup 4.1 Antenna Setup If it is the first time using a receiver, you should set parameters for system configuration. Refer to the following section. Turn on your TV and Satellite receiver. Press the MENU button, main menu screen will appear as shown below. 1. Select Installation on the Main Menu. 2.
Settings and Operations 3. Select correct name of Satellite. If there is no proper satellite name listed in the item, choose one among USER1 ~ USER 5. 4. If you want to change the LNB, go to LNB in the Antenna Setup. 5. If you want to change the LNB go to LNB TYPE and use ◄/► buttons to select the LNB Frequency.
Antenna Setup 6. If only one antenna is in use, please set DiSEqC mode to disable. If more than 1 antenna, you can select DisEqC1.0,DisEqC1.1,DisEqc1.2,USALS. 7. If you have a DiSEqC 1.2 motorized system to control your satellite antenna you have to select DiSEqC 1.2 on DiSEqC mode in Antenna Setup.
Settings and Operations 8. If you want to search channels, press Color button. Red : ch all search , Green : TP search , Yellow : Multi sat search. After successful completion of channel searching, please move to TV Channels or Radio Channels on TV list to select currently received channels. Then you should select the TV channel or Radio channel which you want. After then you can watch the TV program or listen to the radio. [ Multi Sat.
Antenna Setup [ Network Search ] Network search function is enable to search new TPs and all channels in all TPs. * How to go” Network Search” menu : Main menu -> Installation --> Antenna Setup -> Network Search (select “Yes”). NOTE Depending on certain TP or satellite, the Network Search function may not work. [ DiSEqC 1.2 Settings ] If you have a DiSEqC 1.2 motorized system to control your satellite antenna you have to make the following setting. First, you must select DiSEqC 1.
Settings and Operations 2. You should set the East Limit and West Limit of your satellite antenna, if you use the satellite receiver at first. Press OK button on the Change Limit item, set the East/West Limit. 3. Select satellite you want and DiSEqC1.2 Pos. will be set automatically. DiSEqC1.2 Pos. DiSEqC1.2 Pos. shows positioner value of the current satellite. DiSEqC1.2 Command DiSEqC1.2 Command changes the current mode between Installer and User.
Manage Favorite List 4.2 Manage Favorite List Press the MENU button, main menu screen will appear as shown below. Select Manage Favorite List On Installation.
Settings and Operations Rename Favorite Name 1. Press RED button from Favorite List. 2. You can change the character by number button (1~9). To change characters( big/small letter, number), using ▲▼ To delete one character, press Green button.
Manage Favorite List Add Services 1. Press Blue button on Manage Favorite List Menu. Add Services Menu will appear as shown below. 2. You can add channels to Favorite List by Blue button. Then you can see the selected channels on right side.
Settings and Operations 3. To cancel the selected channel, you should select the Favorite List by Red button. Then press Green Button on channel that you want to cancel.
Viewing TV(or Radio) 4.3 Viewing TV(or Radio) 1. Press the Power button. 2. Press the TV(or Radio) button. 3. If you want to see all TV channel list, click the “OK” button and then select the TV Channel (or Radio Channel). TV Channel (or Radio Channel) window will appear. Press [Yellow] button on RCU, you can see available Satellites.
Settings and Operations Edit TV Channels / Edit Radio Channels Press RED button on TV List(or RADIO List) and you can see similar screen will be shown as below. To enter “Edit”, Password is required. The default password is “1234” Rename channel 1. Press RED button from Edit TV List or Edit Radio List .
Viewing TV(or Radio) 2. You can change the character by number button (1~9) To change characters(big/small letter, number), using ▲▼. To delete one character, press Green button. Channel Move Press Green button and then select channels(Green button). Then you can see the selected channels on right side. Select your desired position on left side, Press Yellow button.
Settings and Operations Channel Delete Press Yellow button and then select channels (Green button), you can see the selected channel on right side, if You want to confirm to delete channels, Press Yellow button. Channel Lock Press Blue button for channel lock.
Viewing TV(or Radio) Viewing favorite list Press FAV button on ‘TV list’, you can see the favorite list. Sort Press Green button in the “TV List” screen. You can select the order you want.
Settings and Operations 4.4 System Settings From these menus you can select “System Setting” on the Main Menu. Language Setting Use ◀ ▶ keys to select the desired language. Menu Language For menu language selection, select desired language from Menu Language of system Settings. Audio language Only if a current channel contains 2 or more audio language information, set the Audio Language as English or other favorite language.
System Settings AV Output Settings TV Standard Except for a few, most countries are using PAL system for TV signal, accordingly set TV. Standard as PAL. To be more flexible for NTSC or PAL signal from different satellites, select MULTI for automatic signal conversion. TV Aspect Ratio Press SIZE button when you watch on TV or go to “System Setting” menu. Select “TV Aspect Ratio” and you can change You can change 4:3, 4:3Pan, 16:9Full or 16:9Pillar modes.
Settings and Operations OSD/Screen Setting 27
System Settings CH to CH Selection While you are changing the channel, it shows whether the blank screen or not. OSD Transparency Adjust Transparency on the OSD(On Screen Display) OSD Timeout Set up I-plate Timeout for hidden on / off. TV List Timeout Set up the TV channel list timeout for hidden on /off Subtitle mode You can select subtitle mode ( invisible or visible).
Settings and Operations Parental Control You can protect your installed data and information by locking the menu. Channel lock allows you to lock the channel with the password in order to prevent from accessing of the channel by your children or some unauthorized person. Default password is “9949” for Menu Lock and “1234” for Channel Lock. This can be changes here. Initialization You can initialize All Information to factory default.
Other Functions 4.5 Other Functions Audio Selection If broadcasting channel is supporting multi language, different language can be selected from Audio Selection. 1. To select different language on current channel, press LANG button on RCU. 2. Press OK button on your favorite language. According to different audio data on each channel, different audio language types can be selected. TV Guide Press GUIDE button of RCU for channel information.
Settings and Operations Multi Picture Function You can check other channels (still picture mode) while you are watching a specific alive channel with this function. 1. In the full screen mode, press "M. PICTURE” button on the Remote Control then you will get 4 divided pictures. 2. By pressing "VOL ◀ ▶ CH ▲ ▼" button, you can select a frame one by one. Selected frame will provide you a live picture. 3. Press “OK” button, you can capture the still picture. 4.
Other Functions 2. In Recent Channel List, you can move curser and select channel. If you press Ok button, you can watch the selected channel. 3. Red button: Delete selected channel in Recent Channel List. Favorite Hot button If you press Green button when you are watching TV, selected channel is added Favorite Group as below.
Settings and Operations 4.6 STB Information STB Information You can check Boot, S/W Version, Date, Tuner, Flash Memory. 4.7 CA Information(Optional) CA modules and Smart Cards are licenced to Service Providers. If you want to watch TV Programs from a Service Provider you must use a CA module(Conditional Access) with a Smart Card . If no CA module is used you can only watch FREE TO AIR TV Programs. Press CA Information of “Information menu”. Then, the following sub menu will be shown as below.
Troubleshooting 5.1 Troubleshooting SYMPTOM No picture display and no LED channel display SOLUTION Check the power connection No picture display with normal LED channel display 1. Check the connection with TV 2. Check the connection between TV outside input and receiver cable No satellite channel with MAIN MENU screen on 1. Check the LNB, Frequency, Polarization and Symbol Rate from Installation menu 2. Check the connection of receiver or Antenna Angle No sound with normal screen display 1.
Settings and Operations * Dual Inputs (Satellite & Terrestrial) : − Fully Complies with ATSC HDTV (VSB) & DVB-S MPEG 2 − ATSC Tuner (LG NIM Type) & QPSK (LG NIM Type) − Decodes All ATSC HDTV Standard Video Formats Including 576i / 576p / 720p / 1080i − Selectable Output Video Format : 1080i / 720p / 480p / 480i − Standard Definition/High Definition contents (MPEG2 and support MPEG4 AVC/H.264) * USB 2.
Troubleshooting * * * * * * * Manual PID / Satellite & TP / Network Scan DiSEqC 1.0, 1.1, 1.2 & USALS / 22KHz Switching Control Supported Comparable of setting the frequency for SMATV system Super universal remote UHF ready Fast and Smart Scan High LNB power generation TECHNICAL SPECIFICATION * 1 Input Connector : F-type,IEC 169-24 * IF Input Frequency : 950MHz to 2150MHz * IF Loop Throughout : 950MHz to 2150MHz * Input Level : -65 dBm~-25 dBm * DiSEQqC Control : 1.0, 1.
Settings and Operations * CPU Clock : 280MIPS * Flash Memory : 4 Mbyte + 1Gbyte (Nand flash memory) default (16Gbye nand flash memory : Optional) * SDRAM : 192 Mbyte * EEPROM : 32 Kbit DATA PORT * Connector * Protocol : * Data Rate * Ethernet : : 9 Pin D-Sub Type RS232 Asynchronous : Max. 19.2Kbps 115.
Troubleshooting 38
Appendix 5.3 Glossary LNB Low Noise Block converter. The LNB is an electronic unit mounted on satellite dish to receive signals reflected by the dish and convert to signals. L.O. frequency Local Oscillator frequency as a part of LNB. It converts the satellite frequency to usable signals for the receiver. Polarization Polarization allows several programs to be fitted into same frequency band.
Appendix C band 3~4GHz Frequency SCPC Single Channel Per Carrier MCPC Multi Channel Per Carrier PID Packet Identifier. TP Transponder SCART, RCA A connector for connection of Satellite receiver, VCR and TV sets. VCR Video Cassette Recorder.
MADE IN KOREA