CS203X-2 EPC Class 1 Gen 2 RFID Reader User’s Manual Version 2.
USER'S MANUAL, VERSION 4.0 1 Content 1. Content ………………………………………………………………..……….…………….. 2 ………………………………………………….……..…………… 3 2. FCC and IC Statement 3. INTRODUCTION ON FEATURES ……………………………….….………………… 6 ………………………………………………..…..……………….. 7 …………………………………….…….…..……………… 7 ………………………………………………………………… 8 3.1 CS203X-2 RFID Fixed Reader 3.2 Product Package 3.2.1 Basic Package Content 3.3 Product Specification 4. INTRODUCTION ON APPLICATION ……………………………………..……………...………………. 10 …………………………………….
USER'S MANUAL, VERSION 4.0 2 FCC and FCC Statement FCC regulatory conformance： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
USER'S MANUAL, VERSION 4.0 RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 30 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC regulatory conformance This device complies with CAN ICES-3 (B)/NMB-3(B).
USER'S MANUAL, VERSION 4.0 Cet équipement est conforme aux limites d’exposition aux rayonnements de la IC établies pour unenvironnement non contrôé. Cet équipement doit être installé et fonctionner à au moins 30cm de distance d’un radiateur ou de votre corps.
USER'S MANUAL, VERSION 4.0 3 Introduction on Features 3.1 CS203X-2 RFID Fixed Reader The CS203X-2 RFID fixed reader is a reader designed to work with an any personal computer via the ethernet connection, where the application on the PCs would control the CS203X-2 reader to perform RFID tag reading and GPIO port ON/OFF operation.
USER'S MANUAL, VERSION 4.0 3.2 Product Package 3.2.
USER'S MANUAL, VERSION 4.0 3.3 Product Specification Figure 3-1 CS203X-2 Fixed Reader Features: ISO 18000-6C and EPCglobal Class 1 Gen 2 UHF RFID protocol compliant including dense reader mode Ultra long read range – peak at more than 18 meters for Monza R6 Dogbone tag Sophisticated data handling for efficient management of large streams of tag data.
USER'S MANUAL, VERSION 4.0 Specifications: Physical Characteristics: Length: 26.5 cm; Width: 26.5 cm; Height: 12 cm; Weight: 4180 grams Environment: Operating Temp: -200C to 500C Storage Temp: -400C to 850C Humidity: 5% to 95% non-condensing Antenna: External antenna has a RP-SMA male connector RF Power: Internal conducted power 30 dBm EIRP Power: 35 dBm (max.
USER'S MANUAL, VERSION 4.0 4 Introduction on Application 4.1 Basic Hardware The CSL CS203X-2 RFID Reader is an EPCglobal Class 1 Gen 2 handheld reader product. Below is the front view of the CS203X-2 reader.
USER'S MANUAL, VERSION 4.0 Below is the bottom-side views of the CS203X-2 reader.
USER'S MANUAL, VERSION 4.
USER'S MANUAL, VERSION 4.0 4.2 Power Supply 1) Power Adaptor Unit CS203X-2 reader can be power up with the power adaptor unit included in the package. This will guarantee that CS203X-2 reader can operating in the optimal condition with its internal built-in patch antenna. Below show the typical connection to use the power adaptor. 2) PoE+ Switch CS203X-2 also supports the use of Power over Ethernet (PoE+) switch. Below shows the typical connection of using PoE as the power supply to the CS203X-2 reader.
USER'S MANUAL, VERSION 4.0 4.3 Demo Software on PC The CS203X-2 can be controlled via the Ethernet. In this case user need to connect the PC with CS203X-2 with a Ethernet cable directly or via a router. Below is the screen capture of a Demo application, which is also available for download from Convergence website (www.convergence.com.hk), on PC controlling CS203X-2.
USER'S MANUAL, VERSION 4.0 operations via this PC Demo application as mentioned below. Inventory Tag memory bank read and write GPIO On/Off control Antenna port settings Output power settings Fig 4-7 Main menu of PC Demo application For example, if user need to carry out inventory operation, it is necessary to click the “Inventory” icon in Fig 4-7. The corresponding sub-menu has been shown in Fig 4-8 below.
USER'S MANUAL, VERSION 4.
USER'S MANUAL, VERSION 4.0 4.4 GPIO Port Signals Below figure shows the output and input signal for the GPIO signals.
USER'S MANUAL, VERSION 4.0 Appendix A. Frequency Channel Table FCC Band Channels Channel number Frequency (MHz) Channel number Frequency (MHz) Channel number Frequency (MHz) 1 902.75 18 911.25 35 919.75 2 903.25 19 911.75 36 920.25 3 903.75 20 912.25 37 920.75 4 904.25 21 912.75 38 921.25 5 904.75 22 913.25 39 921.75 6 905.25 23 913.75 40 922.25 7 905.75 24 914.25 41 922.75 8 906.25 25 914.75 42 923.25 9 906.75 26 915.25 43 923.75 10 907.
USER'S MANUAL, VERSION 4.0 Appendix B. Link Profiles of CS203X-2 RFID Reader Link Profile 0 1 2 3 R-T Modulation DSB-ASK PR-ASK PR-ASK DSB-ASK Tari (μs) 25.00 25.00 25.00 6.25 X 1.00 0.50 0.50 0.50 PW (Pulse Width in usec) 12.50 12.50 12.50 3.13 RTcal (usec) 75.00 62.50 62.50 15.63 TRcal (usec) 200.00 85.33 71.11 20.
USER'S MANUAL, VERSION 4.0 Appendix C. Antenna ports operation description CS203X-2 is a reader where the ports are switched on in time one by one. At any time only 1 port is switched on and the RF power comes out only at that port. The rest of the ports are turned off so that no energy comes out from the other ports. Time Slot Antenna Port Status Port 1 Port 2 1 On Off 2 Off On The Antenna should be set up 0.5 meter apart is shown as below: 0.
