User's Manual

ManualsBrandsControlled Electronic Management Systems ManualsElectronicsEmerald Intelligent Fingerprint Terminal

Quick Installation Guide

1 Software Setup

emerald TS300f

Intelligent

Fingerprint

Terminal

Required tools

Specifications

Hex security screwdriver Size H20

Star head screwdriver Size PZ3

-20°C to 70°C (4°F to 158F) flame-retardant polycarbonate. IP65 rated

15W power to the terminal only. Lock and/or exit reader power should be

supplied separately

This guide contains the basic instructions for installing

the emerald TS300f - Intelligent Fingerprint Terminal.

For a complete description of emerald TS300f and its

features, refer to the Technical Product Specification

at:

http://www.cemsys.com/emerald

12v nominal (10v – 14v) @500mA peak. (Typically 300 – 400mA)

Four analogue inputs - voltage supplied

RS485 serial comms using Wiegand protocol

10/100 Base-T TCP/IP CAT5/5e

DC30V @ 5aDry contact outputs

Comms to system host

Comms to exit reader

Inputs

a. If the DC supply is less than 12V @ 500mA a separate PSU is required for the lock

Power over Ethernet

DC power (unit only)

emerald TS300f

Part Rating

TSR-QG-0072-1

1. Open AC2000 | Device Configuration | Devices.

2. In the left pane, expand the Controller to which the terminal is being added.

3. Right click the appropriate Device group and select Add Device.

4. In the Device Type drop down list, select the emerald model being installed

(TS300).

5. In the Configuration Mode drop down list select the setting that matches

your hardware setup.

6. In the Device Number drop down list select a device number.

7. Enter a unique description for the device in Device Location .

8. Enter the unique MAC Address of the device. (To display the MAC Address

on the terminal select System information | Network).

9. Enter the unique IP address of the device.

10. Click Add to complete the setup.

If inputs are used to trigger alarms or events in AC2000 AED they must first be configured

in the AC2000 Devices application. (See AC2000 Setup Guide.)

Ensure that the appropriate card definitions for the chosen card technology are loaded on

the CDC.

Adding the device to AC2000

Configuring Device Inputs

Card Definitions

Wiring Configuration: emerald Fingerprint Reader + S610s SE + 3rd Party Read Head

PSU 12V

2A min

J30

JMP1

SW2

12VGND

J10

J11

SAFETY GND

RS232 RX

SOUNDER

LED GREEN

LED AMBER

LED RED

INT EXT

DRY CONTACT RELAY OUTPUTS: 0-24V DC @ 2A (EXTERNAL SUPPLY)

WET CONTACT RELAY OUTPUTS: 12V DC NOW @ 1.3A (INTERNAL SUPPLY)

DOOR POS

REX

1 RS485 A

1 RS485 B

RS232 TX

3 RS485 A

3 RS485 B

12V 12V0V NO

RELAY 1

0V 0V

INTERLOCK

LOCK POS

RELAY 2

J19 J17

J18

External selected

Battery Link fitted

Ethernet to Switch/Hub

LK5

LK4

LK7

S610s SE Reader

(Serial)

J15

485A

485 B

GND

J10

Keypad

485A

485B

GND

DOOR

POSITION

MAGNETIC

LOCK

SENSE

REQUEST

TO EXIT

3rd Party

Wiegand

Head

LABEL

Ferrite - Double Loop

micro

SD card

In fail-secure configuration, if the terminal loses power the

lock remains closed. A lock that requires power to open

such as a mortice lock must be used.

WIRING NOTES

If the terminal loses power a fail-safe lock opens allowing

free access. Therefore a lock that is constantly powered,

such as a maglock, must be used.

Fail-safe lock

Internal Power Supply

External Power Supply

Fail-secure lock

INT EXT

When using 24V power for a lock, it is imperative that the

switch position is set to EXT. Setting the switch to INT

will result in 24V being supplied to the terminal which

may cause irreversible damage.

When the switch is set to EXT a separate DC12 – 24V

power source must be used to provide power for any locks

or other devices such as sounders attached to the

output (J18).

Note: Connect the PSU +ve to J18 pin C on RELAY 1.

When the switch is set to INT, DC12V 650mA is provided

to the lock or other devices attached to each output from

the terminal’s internal power circuitry.

2 Mounting the Terminal

1. Remove the four screws and spacers using a star head screwdriver.

2. Lift the I/O board away from the back casing.

3. Drill the cable access holes using the guides on the back casing.

4. Drill the the holes on the terminal casing to match the back box fixture points.

Opening the terminal

1. Set the terminal on a level surface.

2. Remove the four screws using

a security hex screwdriver.

3. Remove the front part of the

terminal, pivoting at the base.

4. Disconnect the ribbon cable from

the I/O board.

Mount the back casing to back box

1. Using the drilled mounting holes, screw the back casing to the back box.

2. Screw the I/O board to the back casing, ensuring to replace the spacers.

Removing the I/O board

Summary of content (3 pages)

PAGE 1
Specifications Hex security screwdriver Star head screwdriver Part 2 TSR-QG-0072-1 Mounting the Terminal Opening the terminal 1. Set the terminal on a level surface. 2. Remove the four screws using a security hex screwdriver. 3. Remove the front part of the terminal, pivoting at the base. 4. Disconnect the ribbon cable from the I/O board. emerald TS300f -20°C to 70°C (4°F to 158F) flame-retardant polycarbonate. IP65 rated DC power (unit only) 12v nominal (10v – 14v) @500mA peak.
PAGE 2
3b 4 Wiring Configuration: emerald TS300f + DIU200 + S610s SE NOTE: On the DIU, if BGU, FIRE and TAMPER are not used the LABEL J1 (Serial) J17 DOOR POS LOCK POS REX INTERLOCK 0V 1 RS485 A 1 RS485 B RS232 TX 3 RS485 A 3 RS485 B H0 H1 + GND J3 BGU COM FIRE TAMPER BUZZ – BGU COM FIRE TAMPER BUZZ – BGU COM FIRE TAMPER BUZZ – BUZZ + BUZZ + BUZZ + LK7 LK5 GND EXT J10 485B 485A DRY CONTACT RELAY OUTPUTS: 0-24V DC @ 2A (EXTERNAL SUPPLY) WET CONTACT RELAY OUTPUTS: 12V DC NOW @ 13A (INTERNAL SUPP
PAGE 3
Warnings Warning This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Warning English Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.