emerald TS100/200/300 Installation Manual TSR-IM-0045-1.
Notice The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Copyright Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of © 2013 Tyco Security Products. All Rights Reserved.
emerald TS100/200/300 Installation Manual Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Warning English Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
CHAPTER 1 : iv TSR-IM-0045-1.
Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Terminal specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 CEM emerald product codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Terminal dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal with DIU 210 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Configuration information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Terminal with DIU 230. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Configuration information . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning a remote application group to users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Next Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 6. The System Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Appendix II: Broadcast and Timezone Priorities . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Appendix III: Loading Card Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Appendix IV: Configuring a Third Party Reader as a Master . . . . . . . . . . . . . . . . . 85 Appendix V: User Defined Logo . . . . . . . . . . . . . . .
Chapter 1 Introduction emerald (TS100/200/300) is an intelligent access terminal that provides secure door control with optional intercom and Remote Applications for reporting and configuration. Used as part of the AC2000 system, emerald controls access to restricted areas while giving the user a wide choice of information tools and applications at the door. Microphone Multi-colour status LED Passive IR detector Speaker 4.
CHAPTER 1 : Introduction 1.1 Terminal specifications emerald is available in three models; the TS100, TS200 and TS300. Feature TS100 TS200 TS300 Door access reader Maintenance information point Intercom Remote Applications terminal Table 1: Terminal features Door access reader Configured on an AC2000 system to provide full access control at the door, including monitoring inputs and triggering alarms.
emerald TS100/200/300 Installation Manual Using Desfire EV1 There are two different types of Desfire EV1 card. CEM can provide a personalised Desfire EV1 card, with pre-defined attributes or non-personalised Desfire EV1 cards can be used. If using non-personalised cards, the user should refer to the User Defined Keys manual to configure card keys. 1.1.2 Terminal dimensions Figure 2 Illustration of emerald including dimensions 1.1.
CHAPTER 1 : Introduction 1.1.4 Onboard memory 128MB RAM, 256MB NAND Flash 4 • Up to 250,000 cardholder records (off-line) • Up to 50,000 transactions (off-line) TSR-IM-0045-1.
emerald TS100/200/300 Installation Manual 1.1.5 Terminal key component parts Back casing I/O board Back Ribbon cable Front casing Front board Front Figure 3 Illustration of the key component parts Note All emerald models use the same component parts.
CHAPTER 1 : Introduction 1.2 Simplified AC2000 Network Topology Figure 4 Basic illustration of a typical AC2000 network including emerald configurations Important The emerald terminal is only available as an ethernet device. 6 TSR-IM-0045-1.
emerald TS100/200/300 Installation Manual 1.
CHAPTER 1 : Introduction 8 TSR-IM-0045-1.
Chapter 2 Mounting the Terminal The emerald terminal can be mounted on a variety of standard electrical back boxes: • UK single back box • US single back box • UK double back box mounted vertically • 75mm VESA mount 2.1 Preparing for mounting Care must be taken with the internal components when disassembling the terminal. 2.1.
CHAPTER 2 : Mounting the Terminal 2.1.2 Opening the terminal Important Take care not to strain the ribbon cable connecting the two halves of the terminal. Figure 6 Opening the terminal 1. Set the terminal on a stable, level surface to reduce the risk of the front of the terminal falling when it is disconnected. 2. Remove the four screws using a security hex screwdriver. 3. Carefully lift the top casing away from the back of the terminal, pivoting as shown. 4.
emerald TS100/200/300 Installation Manual 2.1.3 Mounting the terminal back casing To access the mounting screw positions of the terminal the Input/Output board must first be removed from the back box. D D C C A - Back casing B - I/O board C - Spacers D - Mounting screws C B A C D D Figure 7 Exploded view illustration of the back casing and I/O board 1. Remove the four screws and spacers using a star head screwdriver. 2. Lift the I/O board away from the mountings. 3.
CHAPTER 2 : Mounting the Terminal Drilling the back casing Figure 8 emerald back casing drill hole dimensions Mounting hole Description A Generic positions for wall mounting. These holes are accessible when the I/O board is in place. B UK single back box. C US Single back box. D UK double back box mounted vertically. E 75mm VESA mount. Table 5: emerald mounting descriptions 12 TSR-IM-0045-1.
Chapter 3 Wiring the Terminal 3.1 Cabling requirements Table 6 on page 13 outlines recommended cabling requirements for each of the connectors on the emerald terminal.
CHAPTER 3 : Wiring the Terminal 3.2 The Front Board The front PCB contains the main electronic components of the reader; it is also where ethernet communications must be connected. J. Tamper switch A. Reset button I. Network link speed LED H. Ethernet activity LED G. Battery backed clock link B. PoE Indicator LED C. Optional DC12V D. RJ45 E. Ribbon connector to the I/O board F. 12V power LED Figure 9 Illustration of the front board Component Description A.
AC2000 Getting Started Guide 3.3 The Input/Output Board The input/output board provides connections points for terminal power, inputs, outputs,3rd party Wiegand read heads, communications with exit readers and door interface units. I. Input connectors A. Wiegand read head interface H. Comms to exit/DIU B. Output 0 state switch G. Output 1 state switch C. DC12V F. Output 1 (spare) C. DC12V D. Output 0 (lock) E.
CHAPTER 3 : Wiring the Terminal 3.4 Wiring locks The terminal supports lock types rated 12-24V at 1.5A max current if using an external power supply. It is recommended that the lock is powered by an external power supply as this provides the most flexibility. However if required, internal power to a lock can be provided at 12V, 650mA max current. 3.4.1 Wiring a voltage provided lock (internal power) Only12V locks can be wired to be powered internally by the terminal.
AC2000 Getting Started Guide 3.4.2 Wiring a voltage not provided lock (external power) Important When using 24V power for a lock, it is imperative that the switch position is set to EXT. Setting the switch to INT will result in 24V being supplied to the terminal which may cause irreversible damage. This is the recommended wiring configuration when locks require 24V or more than 650mA. Figure 13 Illustration of wiring for lock with external power provided 3.4.
CHAPTER 3 : Wiring the Terminal 3.
AC2000 Getting Started Guide 3.6 Configuration information Wiring an emerald terminal with a request to exit switch is the most basic wiring configuration and is not recommended for use on high security doors. Input configuration The table below illustrates the configuration and operation of the inputs on the terminal when configured with a Request to Exit switch.
CHAPTER 3 : Wiring the Terminal 3.
AC2000 Getting Started Guide 3.8 Configuration information The emerald terminal facilitates the use of a third party exit Wiegand head with three LEDs. Supported third party read heads CEM support the use of HID R10 heads for reading Mifare and iClass cards.
CHAPTER 3 : Wiring the Terminal 3.
AC2000 Getting Started Guide 3.9.1 Configuration information Using a CEM S610s exit reader provides a higher level of security at the door than using a third party read head.
CHAPTER 3 : Wiring the Terminal 3.
AC2000 Getting Started Guide 3.10.1 Configuration information Using a CEM DIU210 provides the highest level of security at a door, removing power for the lock and input monitoring away from the door reader.
CHAPTER 3 : Wiring the Terminal 3.
AC2000 Getting Started Guide 3.11.1 Configuration information Using a CEM DIU230 provides the highest level of security at a door, removing power for the lock and input monitoring away from the door reader. The DIU is a PoE+ device and does not require specialist electrical qualifications to install.
CHAPTER 3 : Wiring the Terminal 3.
AC2000 Getting Started Guide 3.12.1 Configuration Important When powering the emerald terminal using PoE+, the total peak current draw of the attached door furniture must not exceed 840mA. Using a CEM S610s exit reader provides a higher level of security at the door than using a third party read head.
CHAPTER 3 : Wiring the Terminal 3.13 Tamper Detection on Reader Inputs Terminal inputs can be monitored for four state tampering, open, close, tamper short and tamper cut. If an input is tampered with an alarm will be triggered in the AC2000 software. The alarm is a universal tamper alarm and does not distinguish between the four different states.
AC2000 Getting Started Guide 3.13.3 Re-assembling the terminal 1. Ensure that there is adequate cable length available to reach the connectors comfortably for each of the following: – 12vDC – Cat5e/6 cable for communications and / or PoE – Output wiring for lock – Wiring for inputs e.g. door position sensor, lock sense Important To maintain the terminal’s IP65 rating, the cable access hole should be adequately sealed before completing the installation process. 2.
This page is intentionally blank.
Chapter 4 Reader Network Configuration The network settings are accessed via the installer configuration menu on the terminal. 4.1 Checking emerald’s Network Status 1. Tap the Reader Address. The network status indicator is displayed for eight seconds. Network status indicator Figure 21 Checking the network status Each section of the status indicator represents a different aspect of the network connectivity. The presence or absence of a block indicates whether or not the connection is good.
CHAPTER 4 : Reader Network Configuration 4.2 Accessing the Configuration Menu 1. Slowly swipe a finger across the date/time from left to right. 2. When prompted to enter passcode type 67679999. Figure 23 Accessing the configuration menu Note Once the terminal has received a configuration from the server this passcode will be changed to 67670000. The final four digits of this PIN are configurable for the terminal in the Devices application, see section 6.
AC2000 Getting Started Guide 4.2.2 Network routing - (advanced users) The emerald terminal needs to be able to communicate with the Central Database Computer (CDC) and the Real Time Computer (RTC). If a network is fragmented, and the reader, CDC and RTC are on different parts of the network it may be necessary to route communications to the RTC. In this situation contact the site network administrator. 1. From the Configuration Menu press Device Settings | Routing. 2.
This page is intentionally blank.
Chapter 5 AC2000 Software Configuration This section of the manual focuses on the initial addition and configuration of the device and input alarms. All other advanced configuration options will be covered in the relevant function sections. The emerald terminal is added to the AC2000 system and configured using the Devices application. Note This manual assumes access to the necessary AC2000 applications and should be performed by person(s) trained in its use. 5.
CHAPTER 5 : AC2000 Software Configuration 5.2 Adding the device to AC2000 1. From the AC2000 Floatbar open Device Configuration | Devices. 2. Select the controller and device group to which the device is to be added. 3. Right click the device group and select Add Device. Figure 29 The add device dialogue with example terminal information 4. Select the Device Type TS100, TS200 or TS300 from the drop down menu.1 5. Select the Configuration Mode TS 100/200/300 from the dropdown list.2 6.
AC2000 Getting Started Guide 5.2.1 Configuring a 3rd party read head After following the instructions in Adding the device to AC2000 on page 38, a Slave added to a master reader is configured as slave reader by default. To configure the Slave to be a read head only, perform the following steps: 1. From the AC2000 Floatbar, open Device Configuration | Devices.
CHAPTER 5 : AC2000 Software Configuration 5.3 Configuring Device Inputs If inputs are to be used to trigger alarms or events in the AC2000 software they must be first be configured in the Devices application. 5.3.1 Adding an input alarm 1. From the AC2000 Floatbar select Device Configuration | Devices. 2. Select the device to configure from the overview pane. 3. Select the Inputs tab at the top of the main pane. 4. Click Add in the main pane.
AC2000 Getting Started Guide 5.4 Editing emerald Entries in AC2000 The following instructions are only required if the settings need to be edited during or after terminal installation. 5.4.1 Editing device properties 1. Select the master device in the overview pane. 2. Make the required changes and click Save. 5.4.2 Editing a device input 1. Select the Input and the Input State that is to be edited from the Device Inputs 2. Click Save when changes have been completed.
CHAPTER 5 : AC2000 Software Configuration Input table for emerald with S610s exit reader: Input number 0 1 Input function Sensor state AED alarm Door position Open Door forced Closed Door closed Open Lock not engaged Closed Lock engaged Lock position 2 Request to exit No default 3 Spare / interlock No default 4 Spare No default 5 Spare No default 6 Spare No default 7 Spare No default Table 23: emerald and S610s exit reader input alarms Input table for emerald with DIU210 an
AC2000 Getting Started Guide Input table for emerald with DIU230 and S610s exit reader: Input number 0 1 Input function Sensor state AED alarm Door position Open Door forced Closed Door closed Open Lock not engaged Closed Lock engaged Lock position 2 Request to exit 3 Fire 4 5 Break glass Mains power fail No default Open Fire alarm Closed Fire alarm reset Open Break glass Closed Break glass reset Open Mains power fail Closed Mains OK 6 Battery low Open DIU battery low 7
CHAPTER 5 : AC2000 Software Configuration 5.5 Assigning Remote Applications (TS300 model only) To assign Remote Applications to users open AC2000 WEB by typing the IP address of the AC2000 CDC into a browser and select System | Utilities | Remote Apps Allocation Three steps must be taken in order to assign Remote Applications. First, a group or groups are created by user type and then Remote Applications are added to the group.
AC2000 Getting Started Guide 5.5.3 Assigning a remote application group to users To assign a Remote Application Group to a cardholder: 1. Open AC2000SE | Enrolment | Personnel 2. Edit the cardholder’s record and select the appropriate listing from the Remote App. Group drop down list. Remote App Group drop down list Figure 33 Assigning Remote Application Group in Personnel Note If the Remote App Group drop down list is not visible in the Personnel interface, the option has not yet been enabled.
This page is intentionally blank.
Chapter 6 The System Configuration Menu emerald utilises an intuitive Graphical User Interface to access terminal functionality. At the basic level, the screen is used to display meaningful messages regarding the current card swipe transaction. The more advanced options allow the user to access information and reports that are relevant to them. The emerald touch screen is a high quality capacitive screen, which is highly responsive in multiple weather conditions.
CHAPTER 6 : The System Configuration Menu 6.2 Navigation Menus on the Touchscreen terminal are accessed by touching the menu option to expand. • Menus are expanded and closed by pressing the menu name or the arrow. Figure 35 Expanding and closing reader menus 6.3 Accessing the system configuration menu To access the configuration menu: 1. Slowly swipe a finger across the date/time from left to right. 2. When prompted to enter passcode type 6767000.
emerald TS100/200/300 Installation Manual 2. Select Configuration | Other | Diagnostic Pin. 3. Type the new PIN into the text field. 4. Click Save. The system configuration menu has three sub-menus, each of which contains specific terminal maintenance functions. Access useful information about the terminal Configure terminal settings Administer tests to check terminal functionality Figure 37 The system configuration menu 6.3.
CHAPTER 6 : The System Configuration Menu Network The Network menu is used to configure the network settings for the terminal. The IP address assigned to the terminal The SubNet mask of the network that the terminal is connected to The IP address of the Gateway server where appropriate Figure 39 The Network menu Routing The emerald terminal needs to be able to communicate with the Central Database Computer (CDC) and the Real Time Computer (RTC).
emerald TS100/200/300 Installation Manual Options The Options menu is used to change the LCD brightness and update the terminal’s onboard cardholder database.
CHAPTER 6 : The System Configuration Menu 6.3.2 System Information menu This menu contains information about the device including network, firmware version, database and configuration. Important When contacting CEM support with any issues, this information may be asked for.
emerald TS100/200/300 Installation Manual Versions The Versions information section details all hardware and software versions of the terminal. Info Description TSR Version Firmware version UI Version User interface version S/W Date Date of last firmware update S/W Time Time of last firmware update on the S/W Date H/W Version Version of the terminal hardware H/W s/n Serial number of the terminal Linux Linux kernel version, including date and time. Qt Version of Qt library used by the UI.
CHAPTER 6 : The System Configuration Menu Unit information The Unit information section provides information regarding the status of the terminal. Info Description Tamper sensor Describes the status of the internal tamper switch. Run time Information about the running time and load of the terminal. Main comms Indicates the status of the main comms. Database engine Indicates the status of the database engine.
emerald TS100/200/300 Installation Manual Input tests The default Input tests screen displays the four terminal input states. When peripherals such as an exit reader or door interface unit are attached to the terminal, their inputs will also be displayed on the screen. Inputs. Each number correlates with a terminal input number as detailed in chapter 3. e.g input 0 is door position. Input state. To test the inputs, change the state of the input e.g.
CHAPTER 6 : The System Configuration Menu Network tests The Network tests screen provides PING tests to check connectivity with the intercom server and with any other provided IP address. Press to PING the intercom server Press to Ping any to PING the address entered below Type an IP address to PING with the Ping any button Figure 44 Terminal network tests There are two possible responses for the ping utilities: 56 Red: No response received Green: Response received TSR-IM-0045-1.
Chapter 7 Door Modes The emerald terminal can be configured to function in different modes other than the standard door mode described in the main section of the manual. The door modes are: • Door mode including: – Interlock – Multi-swipe • Control post • Passenger mode including: – Interlock 7.1 Door Mode Door mode is the normal terminal configuration that is described in the main installation section of this manual.
CHAPTER 7 : Door Modes 1. The card is swiped at the terminal and access granted. 2. Lock power is dropped for a period of time known as Lock open time. (Five second default) If the door is not opened by the end of this time, the lock re-engages. 3. After the door is opened by the cardholder the lock power remains off for a period of time to prevent the lock re-engaging and closing the door before it is fully opened. This is the Lock open time 2. (One second default) 4. The door is closed.
AC2000 Getting Started Guide configured, an initial valid swipe will prompt a request for further valid swipes on the screen before opening the door. Once all valid cards are swiped the terminal will grant access. Figure 47 Multi-swipe request screen and access granted screen The multi-card swipe screen will show the number of valid cards required to grant access, up to a maximum of five cards.
CHAPTER 7 : Door Modes 7.2 Control Post Mode Control post mode places the terminal into a state where cards are swiped at a terminal with no door equipment present. The terminal acknowledges the card but performs no other action. Transaction logs are still maintained and all events can be observed in real time via the Rolling Transaction Display application. Note All inputs may still be used as general purpose inputs and can be configured to trigger alarms on the AC2000 software. 7.2.
AC2000 Getting Started Guide 7.3 Passenger Mode Passenger mode enables a door to stay open for a longer period of time when swiped with a special usage card. This configuration is frequently used in airports to allow the free access of passengers through the door. 7.3.1 Configuring passenger mode in the software The terminal must be configured in passenger mode and cardholders allocated special usage. Configuring the terminal as a passenger mode terminal 1.
CHAPTER 7 : Door Modes 7.3.2 The passenger mode cycle Figure 52 Illustration of passenger mode timing 1. A card with special usage allocated is swiped at a passenger mode terminal. 2. The terminal prompts whether Staff Access is required or Passenger ops. Selecting staff access causes the terminal to act as in Door Mode. 3. Cardholder selects Passenger ops. Figure 53 Pressing the passenger ops button 4. Lock power is dropped for a period of time known as Lock open time.
AC2000 Getting Started Guide 7.4 Interlock Interlocking terminals are linked together so that only one terminal will open its door at any given time. This is achieved using a combination of wiring and software configuration. Interlocking between two terminals is achieved using a simple wiring configuration, however interlocking more than two terminals requires the use of a third party logic controller or interposing relay system. 7.4.
CHAPTER 7 : Door Modes 3. Open the Input Config panel. Select Input 3 - Config (Input B with DIU) Remove the check from Normal Input Click Save Figure 55 Configuring input 3 for interlock 4. Open the Other tab.
AC2000 Getting Started Guide 7.4.2 The interlock process in door mode Interlock is configured and works the same way in Passenger Mode and Door Mode, with only a slight change to end functionality. 1. The spare outputs of terminals are linked to input 3 of the other interlocked terminals. 2. When input 3 of the terminal is closed the terminal remains idle. 3. When a valid card is swiped at an interlocked terminal, both outputs on the terminal change to the open state.
CHAPTER 7 : Door Modes 5. The interlocked terminals with input 3 now open will lock down, preventing access until the swiped door is closed or the mode ended. Interlocked terminals will display a no passenger access message. Normal card access is allowed. Figure 59 Interlock no passenger access message in passenger mode Important If using a third party logic controller to control multiple doors, the interlock principles remain the same.
AC2000 Getting Started Guide 7.5 Image on Swipe Image on swipe is enabled/disabled within Pre Door Mode configuration. When a cardholder swipes a card on an emerald reader which has Image on swipe enabled, the cardholder’s image is displayed on the screen. A security guard monitoring the reader will confirm if the image on screen resembles the cardholder and select the green tick button to authorise access or the red X button to deny access.
CHAPTER 7 : Door Modes 7.5.2 Configuring Image on swipe options When Image on swipe is enabled and a cardholder presents a valid card at the emerald reader, their cardholder details are displayed below the image. The details displayed are determined by settings in the Configured application in AC2000. 1. From the AC2000 floatbar select Advanced Configuration | Configuration. Image time Options Max size Random message Figure 61 Configuring Image on swipe settings 2.
AC2000 Getting Started Guide The next time that a card is swiped on the reader which has had the Image on Swipe function activated, the image associated with that card will display on the emerald screen. Tapping the green tick on the screen indicates that the image on screen resembles the cardholder and access is granted. Tapping the red X indicates that the image does not resemble the cardholder and access is denied.
CHAPTER 7 : Door Modes 7.5.3 Random checks In certain situations, it may be necessary to perform other checks in addition to authenticating a cardholder’s card and confirming their identity as previously described. If appropriate, your system administrator should implement this procedure and configure the system accordingly. Example: A system administrator configures the system to prompt security guards using an emerald reader that some cardholders need to be tested for drugs.
AC2000 Getting Started Guide d. If no search criteria is entered, acknowledge the warning message that is displayed by selecting Ignore. e. Use the navigation arrows to locate the correct cardholder record from results returned from the search (if required). 4. From the Database Toolbar, select Edit. 5. Click on the User Fields tab. 6. Delete the date entry in the Spare date1 field. 7. Select Save. The random check prompt has now been cleared from the cardholder’s Personnel record.
This page is intentionally blank.
emerald TS100/200/300 Installation Manual Appendix I: Updating Firmware Updating the emerald terminal firmware (device defrosting) is accomplished by using the AC2000 web pages to load the firmware pack on to the terminal and then manually updating the terminal. Important This process should only be carried out by an AC2000 administrator with relevant permissions.
Select the firmware image Select the device type to be defrosted. This should match the firmware file type Select the devices to be defrosted. Hold Ctrl + click multiple devices if required. Ensure that the selected devices are of the correct type.
emerald TS100/200/300 Installation Manual Appendix II: Device Settings Remote Application The Device Settings Remote Application is used to adjust specific terminal settings that would ordinarily be carried out in the Devices application of AC2000. Note For information about configuring Remote Applications see the emerald User Guide. Using the Application 1.
Configuring the options There are nine options that may be configured via this application. All changes made on the terminal are saved on the AC2000 server. After changes are made, press the save button. Lock open time Lock open time sets the length of time in seconds that the lock power will drop when a valid card is swiped.
emerald TS100/200/300 Installation Manual Lock open time 2 Lock open time 2 sets the length of time in seconds that the lock power remains off after the door is opened to prevent the lock accidentally re-engaging. Time in seconds Adjust the time in one second increments by tapping the plus and minus buttons Figure 72 Configuring the lock open time 2 Second swipe action Second swipe action is used to enable an alternative action within a door mode e.g.
Slave settings Toggle settings for any connected slave devices.
emerald TS100/200/300 Installation Manual Workstation group The workstation group option is used to assign an intercom workstation group to the terminal. The terminal intercom function can only communicate with workstations assigned the same workstation group number.
80 TSR-IM-0045-1.
emerald TS100/200/300 Installation Manual Appendix III: Broadcast and Timezone Priorities A state machine is used to determine the priority that different events such as broadcast and timezone changes have on the terminal. The order is listed below in descending priority: 1. Broadcast open 2. Interlock input 3. Locked out TZ (timezone) 4. Door override TZ (timezone) 5. Card only TZ (timezone) 6.
82 TSR-IM-0045-1.
emerald TS100/200/300 Installation Manual Appendix IV: Loading Card Definitions In order for AC2000 to correctly process the information encoded on the smart cards the correct card definitions must be loaded onto the CDC. These are loaded via the AC2000 Web pages. 1. Log into the AC2000 client software. This is done to allow access to the definition files on the CDC. 2. Log into the web pages by opening a web browser. 3. Enter the Server IP Address, e.g. https://192.168.1.
84 TSR-IM-0045-1.
emerald TS100/200/300 Installation Manual Appendix V: Configuring a Third Party Reader as a Master It is possible to configure an emerald with a third party read head as a master reader. This configuration may be used in a system where two card technologies are in use and it is necessary to have two read head technologies on the same side of a door. An exit request (REX) switch may be used to control egress via the same door.
3. Once the device is added, select it from the list and open the Configuration panel. 4. Open the Common panel. Common panel Configuration panel Slave settings Use Slave as Master checkbox Save Figure 82 Setting slave as master reader 5. Select Slave settings from the panel list. 6. Check the option Use Slave as Master.
emerald TS100/200/300 Installation Manual Appendix F: User Defined Logo The Card Logo function is used to display a user defined logo on the emerald terminal. This logo replaces the default CEM logo that appears on the dancing card on the main emerald screen. Existing logo on dancing card User defined logo on dancing card Figure 83 Replacing existing dancing card logo with a user defined logo To display a Card Logo on the emerald terminal, it must be uploaded using AC2000 WEB.
User Defined Logo Enabling the emerald logo change function on the CDC To enable the integration on the CDC: 5. Open an interface with the server, by either: i. Remotely opening a SSH terminal emulator connection (such as Putty) with the CDC. ii. Or, directly accessing the CDC console. 6. Login as user: root 7. Type I in the command line and press return to display the Integrations menu. Figure 86 Integrations menu in a terminal emulator 8.
emerald TS100/200/300 Installation Manual 16. Click ADD CONTENT. Browse to file Upload Return to previous page Figure 88 Uploading a logo 17. Click Browse. 18. Locate the required file and click Open. Note The image must be in PNG format. The recommended size is 287 pixels high by 143 pixels wide and the maximum file size is 90kB. 19. Click UPLOAD. 20. Type a name for the logo in the content name field. 21. Click OK.
User Defined Logo 22. Click SEND. Add additional logo Figure 90 Confirming logo is ready to be displayed on the emerald terminal 23. Click OK when the confirmation prompt is displayed (See Figure 90). This displays a confirmation message that the image has been sent to all emerald readers on the system. Note The logo will only update on each reader, following a car swipe. The uploaded logo will replace the existing logo on the dancing card display on the emerald terminal.
emerald TS100/200/300 Installation Manual 91
CEM Systems 195 Airport Road West Belfast BT3 9ED United Kingdom Tel: +44(0)2890 456767
