User's Manual
Table Of Contents
- Regulatory Compliance & Safety Information for Control4 Model C4-EA3
- Electrical Safety Advisory
- FCC Part 15, Subpart B Unintentional Emissions Interference Statement
- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is opera...
- This device complies with part 15 of the FCC rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference re...
- FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement
- Déclaration d'exposition aux radiations RF Cet équipement est conforme aux limites FCC / IC d'exposition aux rayonnements définies quatrième opération appareils portables transmettre dans un environnement non contrôlé. Les utilisateurs finaux doivent ...
- European Compliance (English)
- European Compliance (German)
- Die Konformität mit den folgenden Richtlinien wird durch die Anwendung des CE-Kennzeichen bestätigt.
- CE-Konformitätserklärung
- Name des Herstellers: Control4 CORPORATION
- Adresse des Herstellers: 11734 S. WAHL ROAD SUITE 200
- SALT LAKE CITY
- UT 84020 USA
- EU-Vertreter Name: Control4 EMEA LIMITED
- EU-Vertreter Adresse: Unit3, GREEN Park Geschäftszentrum
- Sulton-ON-THE FOREST
- YORK YO61 IET, VEREINIGTES KÖNIGREICH
- Produkt-Name (n): Home Controller
- Marke: Contol4
- Modell (e): C4-EA3
- Produkt-Norm (en), um die Konformität der Richtlinie (n) deklariert ist:
- EMC - 2014/30 / EG "Elektromagnetische Verträglichkeit (EMV) Die Richtlinie":
- (Emissionen) EN 55022: 2010, (Immunität) EN 55024: 2010, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2 : 2006 + A1: 2009 + A2: 2009 und EN 61000-3-3: 2008
- Sicherheit - 2006/95 / EG "Niederspannungsrichtlinie (LVD)":
- EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011
- Radio - 2014/53 / EU über Funkanlagen-Richtlinie (RED):
- EN 300 328 V1.9.1
- ErP - 2009/125 / EG Energiebezogene Produktrichtlinie.
- RoHS - 2011/65 / EU zur Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten (EEE) & WEEE - 2002/96 / EG Richtlinie über Elektro- und Elektronikgeräten (EEE).
- Wir, die Unterzeichneten, erklären hiermit, dass das oben angegebene Gerät zu den oben genannten Richtlinien und Normen. Ausstellungsdatum: 22. Dezember 2015
- Gesetzlicher Vertreter
- Stempel, Unterschrift
- Roger Midgley
- Sr. Regulatory Compliance-Ingenieur
- Conformità Europea (Italian)
- Conformità del materiale con le linee guida qui sotto è attestata dall'applicazione del marchio CE.
- Dichiarazione di conformità CE
- Nome del produttore: Control4 CORPORATION
- Indirizzo del produttore: 11734 S. ELEZIONI STRADA SUITE 200
- SALT LAKE CITY
- UT 84020 Stati Uniti d'America
- UE Nome Rappresentante: Control4 EMEA LIMITED
- UE Indirizzo Rappresentante: Unit3, GREEN PARK BUSINESS CENTRE
- Sulton-ON-THE FOREST
- YORK YO61 IET, REGNO UNITO
- Nome del prodotto (s): Casa controller
- Marca: Contol4
- Modello (s): C4-EA3
- Prodotto standard (s) a cui conformità della direttiva del Consiglio (s) è dichiarato:
- EMC - 2014/30 / UE "Compatibilità elettromagnetica (EMC)":
- (Emissioni) EN 55022: 2010, (immunità) EN 55024: 2010, EN 301 489-1 v1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2 : 2006 + A1: 2009 + A2: 2009 e EN 61000-3-3: 2008
- Sicurezza - 2006/95 / CE "Direttiva bassa tensione (LVD)":
- EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011
- Radio - 2014/53 / Direttiva sulle apparecchiature radio dell'UE (RED):
- EN 300 328 V1.9.1
- ErP - 2009/125 / CE Energy legati direttiva sui prodotti.
- RoHS - 2011/65 Limitazione / UE dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche (AEE) e RAEE - 2002/96 / CE sui rifiuti di apparecchiature elettriche ed elettroniche (AEE).
- I sottoscritti, dichiariamo che l'apparecchiatura specificata in precedenza è conforme alle direttive e norme di cui sopra. Data di pubblicazione: 22 dicembre 2015
- Rappresentante legale
- Firma
- Roger Midgley
- Suor Conformità alle normative Ingegnere
- Conformidad Europea (Spanish)
- La conformidad de los equipos con las siguientes pautas es atestiguado por la aplicación de la marca CE.
- Declaración de conformidad CE
- Nombre del fabricante: Control4 CORPORACIÓN
- Dirección del fabricante: 11734 S. ELECCIÓN Road Suite 200
- SALT LAKE CITY
- UT 84020 EE.UU.
- UE Nombre Representante: Control4 EMEA LIMITED
- Dirección Representante de la UE: Tema 3., VERDE PARQUE EMPRESARIAL CENTRO
- Sulton-EN-EL BOSQUE
- YORK YO61 IET, REINO UNIDO
- Nombre (s) del producto: Controlador Inicio
- Marca: Contol4
- Modelo (s): C4-EA3
- Producto estándar (s) a la que la conformidad de la Directiva del Consejo (s) se declara:
- EMC - 2014/30 / UE "Directiva de compatibilidad electromagnética (EMC)":
- (Emisiones) EN 55022: 2010, (inmunidad) EN 55024: 2010, EN 301 489-1 v1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2 : 2006 + A1: 2009 + A2: 2009 y EN 61000-3-3: 2008
- Seguridad - 2006/95 / CE "Directiva de Baja Tensión (LVD)":
- EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011
- Radio - 2014/53 / Directiva de Equipos de Radio de la UE (RED):
- EN 300 328 V1.9.1
- ErP - 2009/125 relacionados con energía / CE Directiva del producto.
- RoHS - 2011/65 restricción del uso de ciertas sustancias peligrosas en equipos electrónicos (AEE) y WEEE eléctricos y / UE - 2002/96 / CE de Residuos de Aparatos Eléctricos (AEE) y electrónicos.
- Nosotros, los abajo firmantes, declaramos por la presente que el equipo anteriormente mencionado se ajusta a las directrices y estándares anteriores. Fecha de emisión: 22 de diciembre 2015
- Representante legal
- Firma
- Roger Midgley
- Ingeniero Sr. Cumplimiento de la normativa
- Conformidade Europeia (Portuguese)
- Conformidade do equipamento com as diretrizes abaixo é atestada pela aplicação da marca CE.
- Declaração de Conformidade CE
- Nome do fabricante: Control4 CORPORATION
- Do fabricante Endereço: 11734 S. ELEIÇÃO ROAD SUITE 200
- SALT LAKE CITY
- UT 84020 EUA
- Representante da UE Nome: Control4 EMEA LIMITED
- Representante da UE Endereço: UNIT3, GREEN PARK CENTRO DE NEGÓCIO
- Sulton-ON-THE FOREST
- YO61 IET YORK, REINO UNIDO
- Nome (s) produto: Início Controlador
- Marca: Contol4
- Modelo (s): C4-EA3
- Padrão do produto (s) a que Conformidade da Directiva do Conselho (s) é declarado:
- EMC - 2014/30 / UE "Compatibilidade Electromagnética (EMC)":
- (Emissões) EN 55022: 2010, (Imunidade) EN 55024: 2010, EN 301 489-1 v1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2 : 2006 + A1: 2009 + A2: 2009 e EN 61000-3-3: 2008
- Segurança - 2006/95 / CE "Directiva de Baixa Tensão (LVD)":
- EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011
- Rádio - 2014/53 / UE Directiva equipamento de rádio (RED):
- EN 300 328 v1.9.1
- ERP - 2009/125 relacionados Energy-/ CE Directiva do produto.
- RoHS - 2011/65 / UE Restrição do Uso de Certas Substâncias Perigosas em Equipamentos Eléctricos e Electrónicos (EEE) e WEEE - 2002/96 / EC de Resíduos de Equipamentos Eléctricos e Electrónicos (EEE).
- Nós, abaixo-assinado, declaro que o equipamento especificado acima está em conformidade com as diretrizes e normas acima referidas. Data de Emissão: 22 de dezembro de 2015
- Representante legal
- Assinatura
- Roger Midgley
- Sr. Engenheiro Conformidade Regulatória
- Recycling
Supported model
• C4-EA3 Entertainment and Automation Controller, 3 Zone
Introduction
The low-cost EA-3 Controller in the Entertainment and
Automation line of controllers lets you control lights, home
theaters, audio and video, and other devices controlled by
infrared (IR), IP, or serial connections. The controller has a
fast processor, dual-spectrum built-in WiFi, HDMI output for
Control4 On-Screen Navigator, and ZigBee radio. The EA-3 is
perfect for single rooms or smaller homes.
The controller also includes extensive media management for
audio and video content: CDs, DVDs, and Blu-ray Discs; digital
media stored on connected devices and streaming audio
services, such as Rhapsody, TuneIn, and others. Use an external
storage device, such as an external USB drive or NAS (network-
attached storage), to store music and photos. The EA-3
Controller mounts easily on a wall behind the TV.
After you install and configure the controller with other Control4
devices, your customers can control their system using popular
Control4 interfaces (sold separately).
Box contents
The following items are included in the box:
• Control4 EA-3 Controller (C4-EA3)
• EA-3 Wall-Mount Bracket (C4-WMEA3)
• AC power cord
• IR emitters (6)
• Dual-band antennas (2)
• Single-position terminal block for contact/relay
• Warranty card
Accessories sold separately
• Control4 3.5 mm-to-DB9 Serial Cable (C4-CBL3.5-DB9B)
• Rack Mount Kit (C4-XXXX)
• EA-3 Wall-Mount Bracket (C4-WMEA3)
Warnings
Caution! To reduce the risk of electrical shock, do not expose
this apparatus to rain or moisture.
Avertissement ! Pour réduire le risque de choc électrique,
n’exposez pas cet appareil à la pluie ou à l’humidité.
Caution! In an over-current condition on USB or contact
output the software disables the output. If the attached USB
device or contact sensor does not appear to power on, remove
the device from the controller.
Avertissement ! Dans une condition de surintensité sur USB
ou sortie de contact le logiciel désactive sortie. (additional
translation needed)
For more information, visit the Products pages at
www.control4.com
.
Requirements and specifications
Note: We recommend using Ethernet instead of WiFi for the
best network connectivity.
Note: The Ethernet or WiFi network should be installed before
you install the EA-3 Controller.
Composer Pro is required to configure this device. See the Composer
Pro User Guide (
ctrl4.co/cpro-ug
) for details.
Specifications
Model number
C4-EA3
Inputs / Outputs
Video out
1 video out—1 HDMI
Video
HDMI 1.4 output; HD 720p/1080p, 50-60 Hz
Audio out
3 audio out—1 HDMI, 1 stereo analog (3.5
mm), 1 digital coax
Audio in
2 audio in—1 stereo analog (3.5 mm), 1 digital
coax
Audio playback formats
MP3: 32 kbps to 320 kbps, iTunes Plus, WMA,
WMA lossless, Apple lossless, CBR, VBR,
AAC, FLAC, and uncompressed WAV and
AIFF.
Network
Ethernet
10/100/1000BaseT compatible (required for
controller setup). PoE+ supported.
Power over Ethernet
802.3af / 12.95W
Built-in Ethernet switch
1 Ethernet/PoE in + 1 Ethernet switch port
Wireless
Dual-Band Wireless-N (2.4GHz, 5GHz,
802.11n/g/b)
Wireless security
WEP, WPA, and WPA2
Wireless antenna
External reverse SMA connector
ZigBee Pro
802.15.4
ZigBee antenna
External reverse SMA connector
USB port
1 USB 2.0 port, 500mA minimum, 600mA
maximum
Control
IR OUT
6 IR out, 5V 27mA max output
1 IR blaster, front
IR capture
1 IR receiver, front; 0-60 KHz
SERIAL OUT
3 Serial out (shared with IR out 1-3)
Contact
1 contact sensor—36V DC maximum
operation. The available current for 12V
contact output is 1.25A maximum.
Relay
1 relay—AC: 36V, 2A; DC: 24V, 2A maximum
operation.
Power
Power requirements
100-240 VAC, 60/50Hz or PoE+
Power consumption
Max: 18W, 61 BTUs/hour
Idle: 9W, 30 BTUs/hour
Other
Operating temperature
32˚ - 104˚ F (0˚ - 40˚ C)
Storage temperature
4˚ - 158˚ F (-20˚ - 70˚ C)
M Ethernet/POE—RJ-45 jack for a 10/100/1000 BaseT Ethernet
connection. Use this port as the ‘uplink port’ to your local network. If
using PoE+ to power the controller, this port must be used.
N ZIGBEE—Reverse SMA connector for ZigBee antenna.
Installing the controller
To install the controller:
1 Ensure that the home network is in place before starting system
setup. The controller requires a network connection, Ethernet
(recommended) or WiFi, to use all of the features as designed.
When connected, the controller can access web-based media
databases, communicate with other IP devices in the home, and
access Control4 system updates.
2 Mount the controller behind a TV, on a wall, placed in a rack, or
stacked on a shelf. See “Wall mount options” below if mounting the
controller on a wall or behind a TV.
3 Connect the controller to the network.
• Ethernet—To connect using an Ethernet connection, plug the data
cable from the home network connection into the controller’s RJ-
45 port (labeled “ETHERNET/POE”) and the network port on the
wall or at the network switch.
Note: If using PoE+ to power the controller, make all
connections prior to plugging in the PoE injector or switch.
• WiFi—To connect using WiFi, first connect the controller to
Ethernet, and then use Composer Pro System Manager to
reconfigure the controller for WiFi.
Important: Do not install your EA controller on a
172.18.xxx.xxx subnet.
4 Connect system devices. Attach IR and serial devices as described
in “Connect the IR ports/serial ports” and “Set up IR emitters.”
5 Set up any external storage devices as described in “Setting up
external storage devices” in this document.
6 Power up the controller. Plug the power cord into the controller’s
power plug port and then into an electrical outlet.
Mounting the controller behind a TV or on the wall
Using the included Wall-Mount Bracket (C4-WMEA3), the EA-3 can
easily be mounted behind a TV, on the wall using a 1- or 2-gang wall
box, or mounted directly on the wall. See the EA-3 Wall-Mount Bracket
Installation Guide for details.
Pluggable terminal block connectors
For the contact and relay ports, the EA-3 makes use of a pluggable
terminal block connector which is a removable plastic part that locks in
individual wires (included).
To connect a device to the pluggable terminal block:
1 Insert one of the wires required for your device into the appropriate
opening in the pluggable terminal block you reserved for that
device (see Figure 3).
2 Insert the wire:
• If using solid-core wire, insert the wire into the hole below the
slotted retention tab, and ensure that the wire is tightly secured.
• If using stranded wire, press the slotted retention tab in using a
small, flat-blade screwdriver. Insert the wire into the hole below
the tab, and then release the tab to secure the wire.
Example: If you add a motion sensor (see Figure 5),
connect its wires to the following contact openings:
• Power input to +12V
• Output signal to SIG
• Ground connector to GND
Note: If you connect dry contact closure devices, such as
doorbells, connect the switch between +12V (Power) and
SIG (Signal).
Control4 EA-3 Controller
Installation Guide
Fan dB level
Max: 35 dB
Dimensions (H x W x D)
8.75" (221 mm) x 5.875" (149 mm) x 1.25"
(31 mm)
Weight
1.60 lbs (0.74 kg)
Shipping weight
2.75 lbs (1.26 kg)
Additional resources
The following resources are available for more support.
• Control4 Knowledgebase: kb.control4.com and Dealer Forums:
forums.control4.com
• Control4 Technical Support
• Control4 website: www.control4.com
• Composer Pro documentation in online help or PDF format available
on the Dealer Portal under Support: ctrl4.co/docs
Front view
A Data LED—The LED indicates that the controller is streaming audio.
B IR window—IR blaster and IR receiver for learning IR codes.
C Caution LED—This LED shows solid red, then blinks blue during the
boot process.
Note: The Caution LED flashes yellow during the factory
restore process. See “Factory Restore” in this document.
D Link LED—The blue LED indicates that the controller has been
identified in a Control4 Composer project and is communicating with
Director.
E Power LED—The blue LED indicates that AC power is connected. The
controller turns on immediately after power is applied to it.
Back view
A WIFI—Reverse SMA connector for WiFi antenna.
B Power plug port—AC power receptacle for an IEC 60320-C5 power
cord.
C Contact/Relay port—Connect one relay device and one contact
sensor device to the terminal block connector. Relay connections are
COM, NC (normally closed), and NO (normally open). Contact sensor
connections are +12, SIG (signal), and GND (ground).
D Serial and IR OUT—3.5 mm jacks for up to six IR emitters or for a
combination of IR emitters and serial devices. Ports 1, 2, and 3 can
be configured independently for serial control or for IR control. See
“Connect IR/serial ports” in this document for more information.
E DIGITAL COAX IN—Allows audio to be shared over the local network
to other Control4 devices.
F AUDIO IN and OUT—Stereo audio input and output ports (3.5 mm
stereo audio jack). Allows audio to be shared (AUDIO IN) over the
local network to other Control4 devices. Outputs audio (AUDIO
OUT) shared from other Control4 devices or from digital audio
sources (local media or digital streaming services such as TuneIn).
G DIGITAL COAX OUT—Outputs audio (AUDIO OUT) shared from
other Control4 devices or from digital audio sources (local media or
digital streaming services such as TuneIn).
H HDMI OUT—An HDMI port to display navigation menus. Also an
audio out over HDMI.
I ID button—Button to identify the device in Composer Pro.
J FACTORY RESTORE—Restores the controller to its factory defaults.
This also reboots the controller.
K USB—One port for an external USB drive. See “Set up external
storage devices” in this document.
L Ethernet—Ethernet port that can be used as a network switch to
connect another local Ethernet device to the network.
A B C D E
A
B C D E F G H I KJ L N
M