User's Manual

ManualsBrandsControl4 ManualsElectronicsINTERIOR DOOR STATION

™

Speciﬁcations

Dimensions (H x

W x D)

7.19” (182 mm) x 5.13” (130 mm) x 2.3” (58

mm)

Weight 3.25 lbs. (1.474 kg)

Shipping Weight 3.25 lbs. (1.474 kg)

Network 10/100 BaseT Ethernet (preferred) or WiFi

(802.11 b/g/n)

Voltages AC - 100V - 240V

DC - 12V - 24V

Contacts (2 sets) DC: 48V

maximum operation (low voltage)

Relays (1) AC: 36V, 2A

DC: 24V

maximum operation (low voltage)

Grounding Requirements

The following table indicates which power options

require an earth ground.

Power Type Earth Ground?

AC Yes; required for safety.

Power over Ethernet (PoE) No; do not connect.

DC Recommended; not required.

Front Panel Description

Figure 1. Front Faceplate

1 Camera. 640 x 480 wide angle. Used for Video

Intercom.

2 Call button. Used to call the person inside the

unit or in another room.

3 Speaker. Used for Audio and Video Intercom.

4 Screw holes (2). Used to screw the faceplate into

the interior wall.

5 Microphones (2). Used for Audio and Video

Intercom.

Supported Models

• C4-DSC-EN-INT Door Station - Interior

AC, DC, POE & WiFi - Satin Black

Box Contents

Carefully unpack the Control4® Door Station from the

box and ensure that the following items are included

in the box. Remove the plastic protector from the

faceplate.

Contact your Control4 Dealer immediately if any

parts are missing or if any components are damaged.

• Control4 Door Station - Interior faceplate (model

C4-DSC-EN-INT)

• Two (2) mounting screws

• Security screw tool

• Warranty Card

Accessories

• Door Station Metal Back Box (C4-DSBB-M, sold

separately)

• Antenna Kit—WiFi/ZigBee 2.4 GHz, 26cm

(C4-AK-26cm, sold separately)

• Antenna Kit—WiFi/ZigBee 2.4 GHz, 3m

(C4-AK-3M, sold separately)

Door Station - Interior

Setup Guide

Summary of content (21 pages)

PAGE 1
™ Specifications Door Station - Interior Setup Guide Dimensions (H x W x D) 7.19” (182 mm) x 5.13” (130 mm) x 2.3” (58 mm) Weight 3.25 lbs. (1.474 kg) Shipping Weight 3.25 lbs. (1.474 kg) Network 10/100 BaseT Ethernet (preferred) or WiFi (802.
PAGE 2
Pre-Installation ™ 1 Find the best location for the Door Station. See “Mounting Tips” below. 2 Door Station - Interior Setup Guide Install the Door Station Back Box. See the Door Station Back Box Installation Guide for details. 3 Determine which network and power options to use (see “Network Options” and “Power Options”). 4 (WiFi only).
PAGE 3
1 Install the Door Station in a place where it will be protected from water. 2 3 Power Options Do not expose the Door Station to direct CAUTION! Do not attempt to use PoE, AC, and sunlight. DC power at the same time. Choose only one Find the best location for the Door Station. See power option. the Door Station Back Box Installation Guide for back box installation. ATTENTION! Ne pas tenter d’utiliser PoE, a Mount the Door Station where the video AC et DC en même temps.
PAGE 4
• WiFi with AC wire from the second back box lug to the home. • WiFi with DC See “Grounding Requirements” for details about • WiFi with PoE earth grounding. 4 Connect the neutral (N) (-) and hot (L) (+) wires Option 1 (Preferred): Ethernet Connection with a to the AC power source for the Door Station PoE Injector or a Third-Party Injector or Switch according to the national and local electrical codes. This option sets up Ethernet with PoE.
PAGE 5
about earth grounding. earth grounding. 4 5 Connect the negative (-) and positive (+) wires 3 Connect the neutral (N) (-) and hot (L) (+) wires to the DC power source for the Door Station to the AC power source for the Door Station according to the national and local electrical according to the national and local electrical codes. codes.
PAGE 6
Option 5: WiFi Connection with DC Power Figure 7. WiFi with DC Power Antenna This option sets up WiFi and DC power. Ensure that you have WiFi in the home. NOTE: WiFi requires an antenna (sold separately). To install the Door Station with WiFi and DC power: 1 Connect a ground wire from the Door Station to one of the back box lugs. 2 Connect a second earth-ground or house-ground wire from the second back box lug to the home. See “Grounding Requirements” for details about earth grounding.
PAGE 7
Figure 8. WiFi with PoE WiFi Antenna Reset/Factory Restore the Door Station To reset or factory restore the Door Station: 1 Remove the faceplate and pull the Door Station out from the back box just enough to expose the Reset button (see Figure 2). 2 While powered press the Reset button on the bottom of the Door Station to reset or restore the Door Station. • Quick press. Press to reset the Door Station. • Long press. Press until the button on the faceplate begins to blink rapidly.
PAGE 8
3 Figure 10. 3m Antenna Kit Thread the other end of the antenna through the back wall of the back box (see Figure 12). Figure 12. Thread Antenna Through Back Box Antenna WiFi Antenna Kit Installation (Optional) Before you install the antenna: 1 Make sure the Door Station is assembled. 2 Make sure the Door Station back box is installed in the wall. See the Door Station Back Box 4 Leave the other end of the antenna hanging outside the back box.
PAGE 9
Figure 13. Contacts and Relays Contacts screwdriver into the slot on the small block that sits between the two rows of holes adjacent to Relays the port and push down firmly. The block will depress. 3 Insert the wire. Ensure that the wire inserts all the way into the hole. 4 Release the screwdriver. Example Wiring Figure 15. Relay Port: Normally Open (e.g., Doorbell) Connect to a Port The Door Station provides six (6) ports for use as two (2) contact sets and one (1) relay (see Figure 14).
PAGE 10
specific to such installation. Control4 makes no Dealers should take time to assure they are not claims, representations or warranties regarding the creating an unforeseen security risk for the customer, security of this product and accepts no liability for and any such risks should be discussed with the any security risk attendant to a specific installation. customer prior to the installation.
PAGE 11
IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Warranty.” Important! Utilisant ce produit en quelque sorte autre que décrit dans ce document vide votre garantie. De plus, Control4 n’est pas responsable d’aucun dommage encouru avec l’abus de ce produit. Voyez que «Warranty.
PAGE 12
™ Requirements • Tools to install the back box, such as a tape measure, pencil, hammer or screwdriver • Nails or screws (4 to 6) • Antenna Kits (optional, sold separately) Door Station Back Box Installation Guide - Antenna, 12” (C4-AK-26cm) - External Antenna, 10’, EWA 2450M (C4-AK-3M) Specifications Dimensions (H x W x D) 6.1” x 4.1” x 3” (156 mm x 104 mm x 76 mm) Weight 1.10 lbs. Network Ethernet or WiFi (802.
PAGE 13
IMPORTANT! Make sure the back box ™ protrudes far enough out (0.118” or 3 mm) from the exterior wall surface (brick, rock, stucco, wood, concrete, etc.) to allow the plate and gasket to seal the Door Station (see Figure 2). Door Station Back Box Installation Guide Figure 2. Back Box Side View in Wall with Door Station Faceplate camera is aimed at an average person’s height so the viewer can see the person calling in.
PAGE 14
4 If using WiFi, the WiFi antenna must be installed in the back box and extend outside the box. Figure 4. Gound Wires from Door Station to Back Box Back Box Door Station Faceplate NOTE: Do not allow any contact of the antenna element to any metal surface on the back box; otherwise, antenna performance will diminish. Figure 3. Ground Wire to Door Station Ground Wire Warnings IMPORTANT! Improper use or installation can cause LOSS/DAMAGE OF PROPERTY.
PAGE 15
Warranty Limited 2-year Warranty. Go to http://www.control4. com/warranty for details. About This Document Part number: 200-00244, Rev. E 6/05/2012 control4.com | 4 ©2012 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners.
PAGE 16
Regulatory Compliance & Safety Information for Contol4 Model C4-DSC-EN-INT. Electrical Safety Advisory Important Safety Information Read the safety instructions before using this product. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
PAGE 17
18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54° C or 130° F. 19.
PAGE 18
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
PAGE 19
This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-210, Antenna Requirements. Do not use any antenna other than the one provided with the unit. RF Radiation Exposure Statement This equipment complies with the FCC/IC radiation exposure limits set fourth for portable transmitting devices operation in an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance.
PAGE 20
Telecom & Radio - 1999/5/EC Radio equipment and Telecommunications Terminal Equipment (R&TTE) Directive: EN 300 328 V1.7.1 (2006-10) RoHS - 2002/95/EC Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE). We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards.
PAGE 21
Recycling Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions.