— F24 DRONE INSTRUCTION MANUAL —
Warning ------------------------------------------------------------ 3-4 -------------------------------------------------------- 5 Flight Safety Remote Control Func�ons -------------------------------------------------------------------------------------- Drone Diagram 6-7 8-10 11 Dual Remote Controller Mode ------------------------------- Remote Control Opera�ng Method ------------------------------- 12 ------------------------------------- 12-22 Install the Con�xo F24 App --------------
PREFACE: Thank you for purchasing the Con�xo F24 GPS drone. Please read all instruc�ons and warnings carefully before opera�ng. Please keep this instruc�on manual for future reference and maintenance. IMPORTANT: 1. This product is not a toy. It is a precision device integra�ng machinery and electronics with air mechanics and high frequency transmission. It requires correct assembly and debugging to avoid any accidents. The user should operate and control this product in a safe manner.
. Avoid controlling it independently. New users may have certain difficul�es during the early stages of learning to operate this drone. Please try to avoid opera�ng the drone alone. When available, always operate this drone under the guidance of a more experienced user. 5. Do not operate under the influence of drugs or alcohol. Please operate this R/C drone according to your own state laws and flying skill. Fa�gue, poor mental state, or incorrect opera�on may increase the probability of accidents. 6.
WARNING: 1. There is important informa�on contained in this package and instruc�on manual, please keep it for future reference. 2. It is your responsibility to ensure that this drone will not cause injury to others or cause any damage to property. 3. Please operate strictly as shown on the instruc�on manual when debugging or assembling this drone.
20. The drone should be kept away from any other electric appliances, equipment, or magne�c objects, as these may cause interference with each other and your drone. 21. Please keep a safe distance from the high-speed rota�ng rotor to prevent dangerous wounds, cuts, or twis�ng in the rotors. 22. The engine will heat up. Please DO NOT touch it to avoid being burned or injured. 23. Please DO NOT put this product close to your ears as it may cause damage to your hearing. 24.
Flight Safety Fly in Open Areas Strong GPS Signal Maintain Line Fly Below of Sight 400 feet (120 m) Avoid flying over or near obstacles, crowds, high voltage power lines, trees, airports or water. DO NOT fly near strong electromagne�c sources such as power lines and base sta�ons as it may affect the onboard compass. DO NOT use the drone in adverse weather condi�ons such as rain, snow, fog and wind speeds exceeding 10 m/s or 22 mph. Stay away from the rota�ng propellers and motors.
It’s important to understand basic flight guidelines, for the safety of both you and those around you. Don’t forget to read the safety guidelines before flight. Remote Control Func�ons 5 6 1 2 3 4 9 10 7 8 1. Thro�le S�ck 2. Direc�on S�ck 3. 1-Click Return-To-Home 4. Power Bu�on: ON – Click Once, White Light Comes ON OFF – Click Once, Then Hold 2 Seconds Un�l White Light Turns Off When there is no opera�on in 10 minutes, the remote controller will be automa�cally powered off.
5. 1-Click Headless Mode (Hold the bu�on for 3 seconds to turn off GPS mode) 6. 1-Click Takeoff with Auto-Hover; 1-Click Landing (Hold the bu�on for 3 seconds for Emergency Stop) 7. 1-Click Photo Capture; Hold 3 Seconds to Enter Trim Mode (Note: No need to trim under the GPS mode) 8. 1-Click Video Recording; Click Again to Stop Video 9. Adjust the Speed – Scroll Right: + Speed Scroll Le�: - Speed 10. Adjust the Camera Angle – Scroll Right: Camera Down Scroll Le�: Camera Up 1 2 3 5 4 7 6 1.
Drone Diagram 1. HD Camera 2. Propeller 3. Propeller Motor 4. LED Indicator 5. Intelligent Ba�ery 5 2 3 4 1 1. Drone Unfold and Fold ①. Drone Unfold Unfold the front arm first, then expand the back arm. 2 2 1 1 ②. Drone Fold Fold the back arm first, then fold the front arm. 1 1 2 2 2. Install the Propellers Please note that the le�er “A” or “B” is printed on each propeller, and make sure all the propellers are a�ached in the correct motor posi�on.
1 2 3 3. Intelligent Flight Ba�ery 1. Power Bu�on 2. Ba�ery Power Indicator 3. USB Charging Port Low Electricity High — To power ON, hold the bu�on for 3 seconds.; To power OFF, hold the bu�on for 3 seconds. — When the ba�ery is at low power, the blue power indicator will start flashing. At this �me, return the drone immediately and charge the ba�ery to avoid unnecessary power failures. 4.
Phone adapter: 5V/ 3A Charging �me: About 4 hours Remote Control Charging Es�ma�on �me : Around 60 minutes Tip: When the remote control ba�ery is low, the power indicator light on the remote control will keep flashing. Please charge the remote control. 5. Lithium Ba�ery Charging Instruc�ons 1. Balanced Charging: Turn the ba�ery OFF before charging. Insert the USB cable into the USB port of the charger and connect to the charging port of the ba�ery to charge.
Dual Remote Controller Mode — Press (camera) then press (power) at the same �me. A beeping sound means the Right Joys�ck has switched to the thro�le s�ck. When you turn off the remote control and turn it on again, the remote resets to default with the Le� Joys�ck as the thro�le s�ck.
REMOTE CONTROL OPERATING METHOD Thro�le Joys�ck Thro�le Joys�ck n Right Tur Turn Le� UP DOWN Forward Le� Right Direc�on Joys�ck kward Bac Direc�on Joys�ck Install the Con�xo F22 App QR code for “Con�xo F22” applica�on for Apple iOS system (Please scan this QR code to install this so�ware). QR code for “Con�xo F22” applica�on for Android system (Please scan this QR code to install this so�ware). Scan the following code with your smart phone in order to download theflight control app.
Flight Step 1: Turn on the drone and set down on a level surface — The drone will auto-trim to this level surface. — All lights blinking red. Thro�le Joys�ck Step 2: Turn On The Remote Control & Pair With Drone — Power on the remote control and push the le� joys�ck up then down to pair with the drone. — When the lights flash blue (back) and white (front), pairing was successful.
First select the drone model F24, then click the “CONTROLS” bu�on to enter the APP interface. 2 1 APP INTRODUCTION Wait un�l the Drone Status at the bo�om le� of the screen reads “Ready to Fly” before ini�a�ng flight. This will ensure that your GPS is synced and your drone is ready to fly.
Step 4: Compass Calibra�on Part 1: Compass Calibra�on — Push the joys�cks into the 1 o’clock (le� joys�ck) & 11 o’clock (right joys�ck) posi�on. — Lights will rapidly blink Blue/Red (back) and White/Red (front). — App Drone Status: “Compass Calibra�on” Part 2: Compass Calibra�on — Keeping the drone level and parallel to the ground, pick it up from the back and rotate your body in one full circle (360°). — Back lights will turn to solid blue.
Part 3: Compass Calibra�on — From the bo�om, hold the drone ver�cally so the camera is facing toward the ground. Rotate your body in one full circle (360°). — Front lights will turn to solid white. — App Drone Status: “Compass Calibra�on Okay” NOTE: If compass does not calibrate quickly, tap the screen on the Con�xo F22 App and restart the calibra�on process. Step 5: Reset to factory Se�ng/Calibrate Gyroscope — Push the joys�cks into the 11 o’clock (le� joys�ck) & 1 o’clock (right joys�ck) posi�on.
Star�ng/Stopping motors Star�ng Motors: 1. Push the joys�cks into the 5 o’clock (le� joys�ck) & 7 o’clock (right joys�ck) posi�on. 2. Motors will begin to start. Push the le� joys�ck up to takeoff or press the 1-Key Take off bu�on. NOTE: Start the motors before drone takeoff. Stopping Motors: 1. Push the joys�cks back into the 5 o’clock (le� joys�ck) & 7 o’clock (right joys�ck) posi�on and the motors will shut off. 2. The motors will go idle if they are not operated a�er 20 seconds.
1-Key Take Off: Press and the propellers will spin and the drone will li� to an al�tude of about 5 feet. (Always keep the front of the drone facing forward). 1-Key Landing: Press and the drone will slowly lower to the ground and land automa�cally. Remember to always keep your hands on the remote control as long as the motor is s�ll spinning.) Emergency Stop: Hold for 3 seconds and the drone will immediately shut off and drop.
Follow Object Click (running person) then click (box around person or Object ). Tap on the object or person you want to track, then tap again to confirm your selec�on. NOTE: Make sure the size of the frame you mark is the same as the object or person you tap, the frame should not exceed the object or person in the capture frame. Selfie Mode Click (hand with two fingers) on the App, follow the “Warm Tip” on the App Screen. Hold up 2 fingers to take a picture. Wave your hand to begin recording video.
Return-to-Home (RTH) The Return to Home (RTH) func�on brings the drone back to the Take Off Point. This func�on can only be achieved under GPS mode. There are 3 types of RTH: Smart RTH/Low-ba�ery RTH/Fail connec�on RTH ①. Smart Return To Home RTH Bu�on RTH Bu�on in App ②. Low-Ba�ery Return-to-Home Low-Ba�ery RTH is triggered when the flight ba�ery level is low. When Low-Ba�ery RTH is ac�vated, the drone will fly back to about 100 feet away from you, where you can control the drone.
Headless Mode 1. The drone defaults to Normal Mode when the drone and remote control are matched successfully. Click (compass) to enter into Headless mode. Click (compass) again to exit Headless mode. 2. Normal Mode: Before take off, the white lights on the drone indicate the forward-facing direc�on. 3. Headless Mode: Before take off, the white lights on the drone indicate the forward-facing direc�on. When the drone rotates in flight, the flight direc�on is not changed.
Adjus�ng Trim in No GPS Mode If the drone flies in None GPS Mode, you can trim the drone to obtain more balanced flight. Press and hold (camera bu�on) for 3 seconds, it will enter trim mode. Holding the bu�on at same �me pushing the direc�on joys�ck to the opposite side that the drone dri�s to rebalance it. For example, if the drone dri�s to the le�, push the joys�ck to the right to make the drone balanced. Release (camera bu�on) to exit trim mode.
Orbit Mode 1. Hover the drone around the center point. 2. Press (camera) + (video camera) on the remote control at the same �me. 3. Move and set the drone in the radius range you prefer (within 6� – 30�) using the direc�on joys�ck. 4. Press (camera) + (video camera) on the remote control at the same �me again. The drone will begin to fly according to the radius range you set in STEP 2 (Note: If the radius range is less than 6 �, the drone will fly to 6 � automa�cally) .
Flight The Default GPS Mode is Beginner Mode. In Beginner Mode: 1. Flight Distance from remote control is limited to between 0 – 90 feet. 2. Flight Al�tude from remote control is limited to between 0 – 90 feet. 3. Return-To-Home Al�tude is below 75 feet. You can turn off the Beginner Mode to modify the parameters in the App on your phone. Flight Se�ng On APP CAMERA FUNCTIONS App Icons Take Photo Take Video Press (camera) on the remote control or tap (camera) on the App to take a picture.
1. One-Bu�on Media Sharing Pic.
Pic. 2 Pic. 3 1. Open the App, click (gallery) to access your picture and video files (Pic 1.) 2. Click once or press (checkmark list) to choose the photos you want to share. Click (box with arrow) to choose the pla�orms to share to (Pic 3). Reminder: You can share up to 9 pictures at the same �me, but you can only choose one video for sharing each �me.
2. How To Find a Lost Drone ①. Click the (satellite) 3 �mes to open the map to search for the drone. ②. The last posi�on of the lost drone will appear on the map, and you can find the last posi�on of the drone according to the label on the map (about 30 � error). Note: The APP must remain open all the �me. If the APP is closed, the last posi�on of the drone will disappear on the map.
Micro SD Card (Sold separately) Micro SD The original images and videos are saved on the Micro SD card. Push the Micro SD card slightly in to click it out. Next, insert the card into the card reader. Insert the card reader into the USB outlet of a computer to retrieve the photos and videos from the Micro SD card. The images can be also viewed in the App. SPECIFICATIONS ● Drone MODEL: F24 Weight (Including Ba�ery): 520g/18.
● App / Live View Mobile App: “Con�xo F22” in App Store & Google Play Store Live View Working Frequency: 5 GHz ISM Live View Quality: 1920x1080P@20fps Smart phone video:1920x1080P@20fps, Photo:1920x1080P. TF card video:1920x1080P@20fps,Photo:1920x1080P (Depend on condi�ons and mobile device) Latency: Low Latency Video (depend on condi�ons and mobile device) Required Opera�ng Systems: iOS 8.0 or later / Android 4.4.4 or later Recommended Devices: 4.7” to 6.
PARTS LIST (Included) Blade x 4 USB cable Only for charging Screw driver x 1 Screw x 12 Charger Instruc�ons x 1 COMMON PROBLEMS AND SOLUTIONS THE PROBLEM REASON TROUBLESHOOT Drone lights flashing and 1. Remote is not synced to 1. Refer to the App Quick Start and re-sync the drone. no response from the drone the drone. 2. Insufficient ba�ery power. 2. Recharge the ba�ery. when opera�ng. The blades spin, but the drone cannot takeoff. 1. Insufficient ba�ery power. 1. Recharge the ba�ery. 2.
Technical Support Have ques�ons ? E-mail: support@con�xo.com Mon-Fri 9:00 am - 4:00 pm PST In order to make sure that your drone meets the requirements of the electromagne�c environment of the avia�on radio sta�on, flying within the scope of 7 miles on each side by taking the airport runway center line as the middle line is HIGHLY FORBIDDEN.Flying within the scope of 13 miles by taking both ends of the runway as the center is HIGHLY FORBIDDEN. Flying on the route of the airline is also PROHIBITED.
CONTACT INFORMATION E-Mail: support@con�xo.com Website: www.con�xo.com ©2018 Con�xo Inc. All rights reserved. Con�xo®, the Con�xo logo and associated characters, trademarks and design elements are owned and licensed by Con�xo Company.
