Access Panel 3 Installation Manual
INDEX 2 Smart Access Control System Introduction 3 Access Panel Installation Prior to Installation ÆÆÐĮĮ qĊÐă wĨÐÆðťÆĴðďĊĮ Access Panel Installation Exit Button Installation Power Supply Installation 4 Ǥ 6 7 8 Lock Type Installation Metal Lock Bracket Electromagnetic Lock Electric Strike 9 11 14 Wiring Diagrams Electromagnetic Lock Electric Strike 24V Lock 16 17 18 Support 19
SMART ACCESS CONTROL SYSTEM 3 Introduction The Rently Access Panel 3 is a cloud-based access panel that can be used to easily track, change, and manage FOB and door code credentials. The Access Panel 3 can be used to control any access device that is operated by a normally open or normally closed signal as long as the voltage requirements are met. NOTE: this system only supports Mifare FOBs and does not integrate with HID FOBS. The Rently Access Panel 3 stores all valid credentials within the device.
ACCESS PANEL INSTALLATION Prior to Installation • Check that all components are available • Rently Access Panel 3 • Screw on co-ax antenna (4 in and 6 ft antennas provided) • Exit Button • Power Supply Controller • Rently Hub • Wall anchors or other mounting hardware • Your preferred lock type including but not limited to: • Electromagnetic Lock and lock bracket • Electric Strike Lock • Electric Bolt Lock • Electric Cabinet Lock • NOTE: This is a kit, and not all components will be used.
ACCESS PANEL INSTALLATION ÆÆÐĮĮ qĊÐă wĨÐÆðťÆĴðďĊĮ #ðĉÐĊĮðďĊĮ ǧǟ Ř ǠǤǟ Ř ǡǧĉĉ ȧǢȘǠ Ř ǤȘǨ Ř ǠȘǠðĊȨ ÐðæìĴ ǦǢǧȘǤæ ȧǠȘǥǢăÅȨ Power Supply 12V/24V AC, 12V/24V DC Output Mode Normally Open/Normally Closed sķðÐĮÆÐĊĴ ķīīÐĊĴ ɗ ǡǤĉ U9 AĊÌķÆĴðďĊ #ðĮĴĊÆÐ ɗ ǠȘǤĉĉ ȧǟȘǟǥðĊȨ Maximum Current 300mA Wireless Connections Bluetooth 4.
ACCESS PANEL INSTALLATION Access Panel Installation 1. Run a power cable to the location where the Rently Access Panel 3 will be mounted. Remove the security screw from bottom of Access Panel 3 with the wrench that is provided and take off the mounting plate. Apply a bead of silicone around the area shown before mounting the plate to the wall. 2. Insert the power and control cables through the mounting plate. ǢȘ qīÐĮĮ ĴìÐ ĉďķĊĴðĊæ ĨăĴÐ ťīĉăř æðĊĮĴ ĴìÐ ĉďķĊĴðĊæ ĮķīåÆÐ ĊÌ secure with screws. 4.
ACCESS PANEL INSTALLATION 'ŘðĴ ķĴĴďĊ wĨÐÆðťÆĴðďĊĮ Size 86 x 86 x 40mm (3.4 x 3.4 x 1.6in) Weight 180g (0.4lb) TÐÆìĊðÆă OðåÐ Ǥǟǟșǟǟǟ ĨīÐĮĮÐĮ Install Location Hollow wall or door ZĨÐīĴðĊæ }ÐĉĨÐīĴķīÐ ȭǢǟɰ Ĵď Ǧǟɰ ȧȭǡǡɰ9 Ĵď ǠǤǧɰ9Ȩ ZĨÐīĴðĊæ >ķĉðÌðĴř ǟɛǨǤɦ ȧīÐăĴðŒÐ ìķĉðÌðĴřȨ Panel Material PC ķīīÐĊĴ tĴðĊæ Ǡǥ ɩǡǤǟ Output Contact NO/COM Exit Button Installation 1. Connect the wires per the wiring diagram section. 2. Pry the plastic faceplate away from the switch body. 3.
LOCK TYPE INSTALLATION 9 TÐĴă OďÆā īÆāÐĴ wĨÐÆðťÆĴðďĊĮ Several brackets are available to accommodate many different types of doors. See diagrams for additional details.
LOCK TYPE INSTALLATION Metal Lock Bracket Installation 1. Measure the gap between the door leaf and door frame. 2. Install the top bracket according to the diagram. Set the screw, keeping the screw head inside the U-shaped slot. 3. Put the rubber mounting plate and iron mounting plate into the U-shaped slot. For easier installation, you may use doublesided adhesive between the rubber mounting plate and the U-shaped slot. 4. Secure the top bracket in the correct position with 4 screws.
LOCK TYPE INSTALLATION 11 Screw Hole Mounting Plate Wire Hole Mounting Plate Location Pin Lock Body Anti-Magnetic Pin Armature Plate Nut Washer Double Door Rubber Ring Armature Plate Single Door 'ăÐÆĴīďĉæĊÐĴðÆ OďÆā wĨÐÆðťÆĴðďĊĮ This type of lock may be used on wood, glass, metal, and ťīÐĨīďďå ÌďďīĮȘ Electromagnetic Lock Installation 1. Remove the screw holding the cover in place, and then remove the cover. 3. Use the hex key again to loosen the mounting plate screws. 2.
LOCK TYPE INSTALLATION 12 Standard Mounting Method 1. Use the template provided to determine the correct location and size of the mounting holes for both the door and frame header. Ensure that the door opens away from the Maglock. In the case of a single door, the Maglock should be positioned as close as possible to the vertical section of the door jamb. Drill the door and frame as indicated. 2.
LOCK TYPE INSTALLATION 13 ǤȘ 'ĊĮķīÐ ĴìÐ īĉĴķīÐ ĊÌ ĉæĊÐĴ īÐ ăðæĊÐÌȘ ÌþķĮĴ ĴìÐ ĉďķĊĴðĊæ plate and then drill the appropriately sized holes in the door header for the remaining screws. 6. Close the door to test the holding force. The angle between the armature plate and magnetic lock can be adjusted by adding or reducing washers.
LOCK TYPE INSTALLATION 'ăÐÆĴīðÆ wĴīðāÐ wĨÐÆðťÆĴðďĊĮ #ðĉÐĊĮðďĊĮ Ǡǡǣ Ř Ǣǡ Ř ǢǡȘǤĉĉ Voltage 12VDC ķīīÐĊĴ ǡǤǟĉ Electric Strike Installation 1. Cut away an opening to the appropriate size based on the diagram above. 2. Run the wires through the door frame and to the Electric Strike. 3. Refer to the wiring diagram section for Electric Strike wiring. 4. Secure the Electric Strike using the screws provided.
LOCK TYPE INSTALLATION 15 The American Standard Electric Strike is normally set to a fail-safe ÆďĊťæķīĴðďĊ ÅķĴ ĉř ÅÐ ĉĊķăăř ÆďĊťæķīÐÌ Ĵď åðăȭĮÐÆķīÐ Åř following these steps: 1. Remove the two screws holding the faceplate using a star wrench. Set the faceplate and inner bracket aside. 2. Next, remove the two screws holding the locking cylinder in place. Slide the cylinder to the second position as shown and secure in place using the same screws that were removed.
WIRING DIAGRAMS 16 NOTE: Please refer to your local building codes and property requirements for appropriate fail-safe and fail-secure wiring.
WIRING DIAGRAMS 17 Scenario B: Electric Strike (Fail-Safe) Power Supply + Input: 110V AC 50Hz Output: 12V DC ǡ + Power Supply Strike Lock Scenario C: Electric Strike (Fail-Secure) Power Supply + Power Supply Input: 110V AC 50Hz Output: 12V DC ǡ + Strike Lock
WIRING DIAGRAMS 18 Scenario D: Fail-Safe 24V Lock 24V Power Supply (Model: PS08) Exit Button 24V Lock Mode: open when power off security Scenario E: Fail-Secure 24V Lock 24V Power Supply (Model: PS08) Exit Button 24V Lock Mode: close when power off security
INSTALLATION TEST With the components installed and wired, please carry out this simple test to ensure that the Rently smart access control system was installed correctly and is fully functional. To ensure that the wiring was done correctly, please press the exit button to see if the lock releases for a few seconds. If the test fails, please reexamine the installation and wiring of the Rently smart access control system. If the test is successful, please install and power on your Rently Hub.
FCC WARNING }ìðĮ ÌÐŒðÆÐ ÆďĉĨăðÐĮ œðĴì ĨīĴ ǠǤ ďå ĴìÐ 9 tķăÐĮȘ ZĨÐīĴðďĊ ðĮ ĮķÅþÐÆĴ Ĵď the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.