Datasheet Nano Socket iWiFi G2 N2 Version 1.1 Connect One Ltd. 20 Atir Yeda Street, Kfar Saba 44643, Israel | Phone: +972-9-766-0456 | Fax: +972-9-766-0461 Email: sales@connectone.com | www.connectone.
Nano Socket iWiFi G2 N2 –Datasheet Information provided by Connect One Ltd. is believed to be accurate and reliable. However, Connect One Ltd. assumes no responsibility for its use, nor any infringement of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent rights of Connect One Ltd. other than for circuitry embodied in Connect One’s products. Connect One Ltd.
Nano Socket iWiFi G2 N2 –Datasheet iChip, Nano Socket iWiFi G2 N2, IP Communication Controller, SerialNET, AT+i and Connect One are trademarks of Connect One Ltd. Copyright 2014 Connect One Ltd. All rights reserved. Industry Canada Warning Statements: This device complies with Industry Canada’s licence-exempt RSSs.
Nano Socket iWiFi G2 N2 –Datasheet Table of Contents Revision History .................................................................................................................................................... 6 1. Introduction ................................................................................................................................................... 7 1) General Description ...................................................................................................
Nano Socket iWiFi G2 N2 –Datasheet 2) DC Operating Characteristics .................................................................................................................. 18 3) AC Operating Characteristics .................................................................................................................. 19 4) Transmit Specification ............................................................................................................................
Nano Socket iWiFi G2 N2 –Datasheet Revision History Version 1.0 1.
Nano Socket iWiFi G2 N2 –Datasheet 1. Introduction 1) General Description Nano Socket iWiFi™ G2 N2 is a secure serial-to-Wireless-LAN device module that can perform as a WLAN client or Access Point to connect serial devices to 802.11b/g/n Wireless LANs. It includes the iChip™ CO2144 IP Communication Controller™ chip and Broadcom BCM43362 WiFi chipset. It is packaged 45.21X24.88 RoHS-compliant module with two 1X15 PIN headers and onboard antenna.
Nano Socket iWiFi G2 N2 –Datasheet Nano Socket iWiFi G2 N2 firmware – the IP stack and Internet configuration parameters – are stored in an external FLASH memory. The II-EVB-363-G2-N2 evaluation board provides an easy environment for testing the Nano Socket iWiFi G2 N2 prior to designing it into your product.
Nano Socket iWiFi G2 N2 –Datasheet 2) Hardware Description Size: 45.21 x 24.88 x 9.00 mm Core CPU: 32-bit RISC ARM7TDMI, Low-leakage, 0.13 micron, at 48MHz Operating Voltage: +3.
Nano Socket iWiFi G2 N2 –Datasheet 7) Wireless Specifications Standards supported: IEEE 802.11b/g/n Frequency: USA: 2.412-2.462GHz Canada: 2.412–2.462GHz Channels: USA: Canada: 11 channels 11 channels 8) Certification Radio & EMC: USA FCC Limited Modular Approval CFR Title 47 FCC Part 15, Subpart B and C Canada Industry Canada Limited Module Approval Industry Canada ICES-003, RSS-Gen, RSS-210 EU EN 300 328 EN 301 489 Safety: UL 60950 CAN/CSA-C22.2 No.
Nano Socket iWiFi G2 N2 –Datasheet 2.
Nano Socket iWiFi G2 N2 –Datasheet 3. Typical Applications Adding IP communications over WiFi to serial embedded devices. Replacing a LAN cable with a WiFi connection. Adding SSL security to M2M solutions. LAN to WiFi Bridge - allowing transparent bridging of LAN client over WiFi (Cable replacement), using direct RMII connection to existing MAC hardware or direct PHY-to-PHY connection.
Nano Socket iWiFi G2 N2 –Datasheet LAN WiFi / WiFi LAN Gateway – allowing local systems, communicating over LAN and/or WiFi, to gain WAN access to the Internet. The WAN can be implemented using WiFi / LAN. A user configurable parameter allows the WAN to be configured to one of the iChip network interfaces. This mode includes a DHCP server and NAT to support multiple local systems communicating over a single link. WiFi 802.11 b/g/n IW-SMG2N2 Access point WAN HOST Computer 4.
Nano Socket iWiFi G2 N2 –Datasheet 5. Layout, Mechanical Dimensions and Pin Description 1) Layout and Mechanical Dimensions Side View 1.20 Headers: Two 1X15pin Male 2mm pitch Mate with: Two 1X15 Female 2mm Pitch Samtec Part Number: #SQT-115-01-F-S 1.60 Or compatible 3.90 2.00 0.50 SQ Top View 2.00 16.00 24.88 5.00 2.00 Ø2.20 34.00 Ø4.00 45.21 2.00 Bottom View 2.00 1 15 J9 J8 1 All measurements are in mm. Tolerance: Length/Width +/-0.15mm, PCB thickness +/10%, Plated bores: +/-0.
Nano Socket iWiFi G2 N2 –Datasheet 2) Pin Functional Description J8 Pin Assignment Pin Signal Type Description 1 ERX0 Input RMII Receive Data 0 2 ERX1 Input RMII Receive Data 1 3 EMDC Output Management Data Clock 4 ERXER Input RMII Receive Error 5 RMII REFCLK Input RMII 50Mhz Reference Clock 6 GND Power Ground 7 VDD Power VDD 8 RXD0 Input UART 0 Receive 9 TXD0 Output UART 0 Transmit 10 nCTS0 Input UART 0 Clear To Send 11 nRTS0 Output UART 0 Request To Send 12
Nano Socket iWiFi G2 N2 –Datasheet 12 DDM Analog USB Device Negative 13 DDP Analog USB Device Positive 14 N.C. 15 GND Not Connected Power Ground 6. Interfaces 1) Serial Interface RXD0 TXD0 nCTS0 nRTS0 Nano G2 N2 J8 Note: If UART is not used, leave TXD0 and RXD0 N.C and short nCST0 to nRTS0 2) SPI Interface nSPI1 CS SPI1 CLK SPI1 MISO SPI1 MOSI SPI1 INT Nano G2 N2 J9 Note: If SPI is not used leave all signals N.
Nano Socket iWiFi G2 N2 –Datasheet 3) USB 2.0 Device Interface 3 27Ω 2 27Ω 4 15pF 15pF USB B Nano G2 N2 J9 Note: If USB is not used leave all signals N.C 4) RMII Interface REF CLK ERXER EMDC ERX1 ERX0 Nano G2 N2 J8 ETX EN CRSDV EMDIO ETX1 ETX0 Nano G2 N2 J9 Note: If RMII is not used leave all signals N.
Nano Socket iWiFi G2 N2 –Datasheet 7. Electrical Specifications 1) Absolute Maximum Ratings Parameter Voltage at any pin with respect to ground Operating Temperature Storage Temperature Rating -0.3V to +3.6V -30⁰C to +85⁰C -40⁰C to +85⁰C -22⁰F to +185⁰F -40⁰F to +185⁰F 2) DC Operating Characteristics Parameter VDD High Level Input Low Level Input High Level Output @2mA High Level Output @0mA Low Level Output @2mA Low Level Output @0mA Input Leakage Current Power Supply Current from VDD (Tx.
Nano Socket iWiFi G2 N2 –Datasheet 3) AC Operating Characteristics 4) Transmit Specification Transmit Error vector Magnitude 802.11b 11Mbps 1Mbps 802.11g 54Mbps 6Mbps 802.11n HT20M@MCS0 HT20M@MCS0 -13 -13 -30 -30 -30 -30 -11 -11 -25 -22 -22 -28 Condition 802.11b Data Rate = 11Mbps PER < 8% 802.11b Data Rate = 1Mbps PER < 8% 802.11g Data Rate = 54Mbps PER <10% 802.11g Data Rate = 6Mbps PER <10% 802.11n MCS0 PER <10% 802.
Nano Socket iWiFi G2 N2 –Datasheet 8. On Board Antenna 1) Specifications Designed for: 2.4Ghz operation Peak Gain: 2.1DBi Avg. Efficiency: 75% Max Return Loss: -11DBi Max VSWR: 1.
Nano Socket iWiFi G2 N2 –Datasheet 9. Evaluation Board The II-EVB-363-G2-N2 evaluation board enables you to evaluate the Nano Socket iWiFi G2 N2 without changing anything in your current development environment. Using a simple Windowsbased application on a PC, you can issue AT+i commands. AT+i commands are used to configure parameter values into iChip’s flash memory and activate Internet tasks such as email send, sockets, FTP sessions, configuration, and more.
Nano Socket iWiFi G2 N2 –Datasheet Appendix A - Internet Protocol Compliance Nano Socket iWiFi G2 N2 complies with the Internet standards listed in the following table RFC 768 User datagram protocol (UDP) RFC 791 Internet protocol (IP) RFC 792 ICMP – Internet control message protocol RFC 793 Transmission control protocol (TCP) RFC 821 Simple mail transfer protocol (SMTP) RFC 822 Standard for the format of ARPA Internet text messages RFC 826 Ethernet address resolution protocol (ARP) RFC 959
Nano Socket iWiFi G2 N2 –Datasheet Appendix B – AT+I Configuration Examples Automatically connect to a specific Access Point: AT+iFD (restore to factory defaults) AT+iHIF=1 (set the serial interface to RS232) AT+iBDRF=9 (fix baud rate to 115200 after power cycle) AT+iRP20 (list visible networks) AT+iWLSI=My_WiFi AT+iWST0=4 (WPA2 security) AT+iWPP0= AT+iAWS=1 (enable website upon reboot) AT+iDOWN (reboot to apply settings) Create an Access Point to allow connection from mobil
Nano Socket iWiFi G2 N2 –Datasheet AT+iedip=192.168.0.100 (Ethernet side IP address) AT+iesnt=255.255.255.
