Connect One Confidential user manual August 2014 560 S. Winchester Blvd. Suite 500 San Jose, CA 95128 Tel: +1 (408) 572-5675 Fax: +1 (408) 572-5601 20 Atir Yeda Street st 1 floor Kfar Saba 44643 Israel Tel: +972-9-766-0456 Fax: +972-9-766-0461 www.connectone.
Connect One Confidential user manual Table of Contents 1. INTRODUCTION TO FIRMWARE I2128D810D81 MBCM ..................................................... 3 2. UNPACKING INSTRUCTIONS ................................................................................................ 3 3. AT+I COMMANDS .................................................................................................................... 4 4. EXAMPLE 1: TEST TX FUNCTIONS.....................................................
Connect One Confidential user manual 1. Introduction to firmware i2128D810D81 MBCM This firmware is provided with the intention of assisting customers of Connect One in performing certification tests for WiFi systems. This firmware is not recommended for release with production units and does not support the full functionality of the production version i2128D810D34. The AT+i commands, which are described in this document, control a special test mode of Broadcom’s 43362 802.11 b/g/n chipset. 2.
Connect One Confidential user manual 3. AT+i Commands Test AT+i Command parameters description Set RF channel MTCH=x x = [1-14] X= channel 1 - 14 Set TX rate MTTR=r r = 1 for 1 mbps, r = 2 for 2mbps, r =5 for 5.
Connect One Confidential user manual TX continuous MTCM=e e = 1 – enable mode, e = 0 – disable this mode mode SET Inter Packet Gap in us TTO=uS On uSEC (20-100) Packet length IATO=l Length (1000-2000) Reset ichip DOWN 4. Example 1: Test TX functions 1. Power up the iChip and the RF processor. 2. Set channel 1: AT+iMTCH=1 3. Set rate 1 Mbit/sec: AT+iMTTR=1 4. Set power 15dbm: AT+iMTRP=15 5. Set SET Inter Packet Gap 20us: AT+iTTO=20 6. Set Packet length 3000: AT+iiato=3000 7.
Connect One Confidential user manual 5. In Case of Failure Please contact our technical support via email: support@connectone.com Alternatively, call the office in Israel: +972-9-766-0456 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Connect One Confidential user manual IC STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Nano WiReach G2 N1 – Preliminary Datasheet 5. Layout and Pin Description 1) Layout Connector: Molex 53748-0308 Mate with: Molex 52991-0308 2) Pin Functional Description Pin Signal Type Description 1 VDD Power 2 GND Power 3 RXD0 Input UART 0 receive 4 TXD0 Output UART 0 Transmit 5 nCTS0 Input UART 0 clear to send 6 nRTS0 Output UART 0 request to send 7 DATA_RDY Output Data ready. Signals incoming Internet data. 8 MSEL Input Mode select.
Nano WiReach G2 N1 – Preliminary Datasheet 11 nSPI1_CS Input SPI 1 chip select for host 12 SPI1_CLK Input SPI 1 clock for host (Max 12MHz) 13 SPI1_MISO Output SPI 1 slave out for host master in 14 SPI1_MOSI Input SPI 1 slave in for host master out 15 SPI1_INT Output SPI 1 have data on his buffer 16 Readiness Output iChip Ready status line. See AT+I programmers manual.
Nano WiReach G2 N1 – Preliminary Datasheet 6. Interfaces 1) Serial Interface RXD0 TXD0 nCTS0 nRTS0 Nano G2 N1 Connector 2) SPI Interface nSPI1 CS SPI1 CLK SPI1 MISO SPI1 MOSI SPI1 INT Nano G2 N1 Connector 3) USB 2.
Nano WiReach G2 N1 – Preliminary Datasheet 4) RMII Interface ETX EN REF CLK CRSDV ERXER EMDIO EMDC ERX0 ERX1 ETX0 ETX1 Nano G2 N1 Connector 17
Nano WiReach G2 N1 – Preliminary Datasheet 7. Electrical Specifications 1) Absolute Maximum Ratings Parameter Voltage at any pin with respect to ground Operating Temperature Storage Temperature Rating -0.3V to +3.6V -30⁰C to +85⁰C -40⁰C to +85⁰C -22⁰F to +185⁰F -40⁰F to +185⁰F 2) DC Operating Characteristics Parameter VDD High Level Input Low Level Input High Level Output @2mA High Level Output @0mA Low Level Output @2mA Low Level Output @0mA Input Leakage Current Power Supply Current from VDD (Tx.
