m1D~@ DIGITAL AUDIO @ I I @ CONCERTONE. @ I I @)...[IJ[]...(@ 0 0 @ IIII III IIIII IIII@ Ii @ @ I lJ V II @ + II @ .
~ WARRANTY ONE (1) YEARLIMITED WARRANTY CONCERTONE warrants to the original retail purchaser of this radio that it or any part therein, under normal use and conditions, be proven defective in material or workmanship within 1 year from the date of original purchase, such defect/s will be repaired or replaced at CONCERTONE'S option without charge for parts and repair labor.
NAMES OF CONTROLS 1. 2. 3. 4. Mounting screw hole Cassette compartment TONE control knob POWER ON indicator 5. 6. 7. 8. 9. LCD display TUNING/SKIP ~ button POWER ON/OFF button STOP/BAND button REMOTE SENSOR 10. Tape Eject/Fast Forward button 11. A/A+B/B SPEAKER selector switch 12. SPEAKER BALANCE control knob 13. CD DOOR OPEN/CLOSE button 14. X-BASS indicator 15. ~II PLAY/PAUSEbutton MEMORY. CLOCK control 16. 17. FUNCTION (CD/TUNER/TAPE/AUX) button 18. SLEEPITIMER button 19. SNOOZE button 20.
NAMES OF CONTROLS - REMOTE 1. DISPLAY button 2. POWER button 1 2 3 4 5 10 6 .12 13 7 8 9 CONTROL 3. FUNCTION (CDITUNERfTAPElAUX) button 4. PRESET/REPEAT button 5. . STOP/BAND button 6. ... TUNING / SKIP buttons 7. MEMORyebutton 8. RANDOM button 9. SLEEP button 10. SNOOZE button 11. PLAY/PAUSEbutton 12. ... TUNING / ~ SKIP buttons 13. X-BASS button 14. INTRO button 15. TIMER button 16.
TURNING ON THE UNIT TOTURN OFF THE UNIT Press the POWER ON/OFF button to STANDBY, the POWER ON indicator will turn off and the clock display will be shown. TO TURN ON THE UNIT Press the POWER ON/OFF button, the POWER ON indicator will light up. Select the desired function and the corresponding function indicator will light up. CLOCK SETTING TUNING 1. In standby mode, press and MEM button for hold the about 3 seconds until time format blinks on display. 4.
TIMER OPERATION The power can be turned on automatically at a preset time so that you can wake up and listen to the TAPE, CD or RADIO. Make sure the clock is correct before TIMER PLAY. Please refer to CLOCK setting procedure. 1. Press and hold TIMER button for about 3 seconds until "TIMER"indicator blinks on display. 6. Press the FUNCTION button to select the desired program source: CD: Insert a disc. TUNER: Select a BAND and station. TAPE: Insert the cassette tape.
LISTENING TO THE RADIO TUNING INTO A STATION MANUALLY 1. Press the FUNCTION button to TUNER. 3. Pressthe TUNING! SKIP ~ buttons to select a station. FUNCTION ~ 2. Pressthe . STOP/BAND Smp/BAND button to select the.desired band. ~ TO SEARCH FOR A STATION AUTOMATICALLY Press the TUNING/SKIP ~ button for 1 to 2 seconds, and a station is searched for automatically. After tuning in a station, the search stops. The search may not stop at a station with a very weak signal.
CD PLAYBACK 1. Press the FUNCTION CD. button to 2. Press the CD OPEN/CLOSE button to open CD door. Place a disc in the CD tray with the label face front and then press the CD OPEN/CLOSE button to close CD door. The total number of tracks will show on the display. FUNCTION ~ CDDOOR OPEN! CLOSE 3. To start playing, press the ~II PLAY/PAUSE button. TO INTERRUPT PLAYBACK Press the ~II PLAY/PAUSE button. The track time will blink. To resume playback, press the PAUSE button again. ~II PLAY/ NOTE: 1.
PROGRAMMING TRACKS - in a CD stop mode (Up to a maximum of 20 tracks) 1. Pressthe e MEM button. 3. Pressthe e MEMbuttonagain. 0MEM 0MEM -- n IJ , -,"""::- I , -- nn ,I . . P-O 2. Press the .... SKIP the desired tracks. -I ED> P-02 IJIJ buttons to select TUNING UP l= ED> 4. Repeat step 2 and 3 to program additional tracks, after you have finished program and memory indicator is blinking on display.
INTRODUCTION PLAY - at CD stop mode and CD play mode (for remote only) This function allows the first 10 seconds of each track of the disc to be played. Pressthe INTRObutton. INTRaappearsin the displayon the unit. RANDOM PLAY - at CD play mode and CD stop mode (for remote only) All the tracks on the disc can be played in random order. Pressthe RANDOMbutton. RANDOMappearsin the displayon the unit. .. 4D> """'n IJ , , ....""" 4D> n n. In '-' ,-,. "_, To cancel introduction play Press the .
MAINTENANCE CLEAN CD If the CD skips or will not play, the disc may need cleaning. Before playing, wipe the disc fromthe centre out with a cleaning cloth. After playing, store the disc in its case. CLEANING THE UNIT Do not use volatile chemicals on the unit. Clean by lightly wiping with a soft cloth. IMPORTANT NOTICE: Should the CD door be opened before the CD is completed, a jamming noise may occur. This can be resolved by closing the CD door and then press the TAPE button temporarily.
SYSTEM CONNECTIONS CONNECTION DIAGRAM Make correct connections the connection ~o m ==~ == == == in From Antenna From TV or other AUX input iii 0 == === as illustrated diagram. 0 === === ~~~~ === == == SPEAKER CONNECTIONS Make sure you connect each lead to the correct terminal according to the colors of leads listed as illustrated in the diagram. Insulate the end of the unused lead with a piece of tape.