8.3 SNMP Agent Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in this device. Select the Enable radio button, configure options, and click Save/Apply to activate SNMP.
8.4 TR-069 Client WAN Management Protocol (TR-069) allows an Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Select desired values and click Apply/Save to configure TR-069 client options. The table below is provided for ease of reference. Option Description Enable TR-069 Tick the checkbox to enable. OUI-serial The serial number used to identify the CPE when making a connection to the ACS using the CPE WAN Management Protocol.
Option Description ACS URL URL for the CPE to connect to the ACS using the CPE WAN Management Protocol. This parameter MUST be in the form of a valid HTTP or HTTPS URL. An HTTPS URL indicates that the ACS supports SSL. The “host” portion of this URL is used by the CPE for validating the certificate from the ACS when using certificate-based authentication. ACS User Name Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol.
8.5 Internet Time This option automatically synchronizes the router time with Internet timeservers. To enable time synchronization, tick the corresponding checkbox , choose your preferred time server(s), select the correct time zone offset, and click Save/Apply. NOTE: Internet Time must be activated to use 5.5 Parental Control. In addition, this menu item is not displayed when in Bridge mode since the router would not be able to connect to the NTP timeserver.
8.6 Access Control 8.6.1 Passwords This screen is used to configure the user account access passwords for the device. Access to the NexusLink 3112u is controlled through the following user accounts: • The root account has unrestricted access to view and change the configuration of your Broadband router. • The support account is typically utilized by Carrier/ISP technicians for maintenance and diagnostics.
Note: Passwords may be as long as 16 characters but must not contain a space. Click Save/Apply to continue.
8.6.2 Service Access The Services option limits or opens the access services over the LAN or WAN. These access services available are: FTP, HTTP, ICMP, SNMP, TELNET and TFTP. Enable a service by selecting its dropdown listbox. Click APPLY/SAVE to activate.
.6.3 IP Address The IP Address Access Control mode, if enabled, permits access to local management services from IP addresses contained in the Access Control List. If the Access Control mode is disabled, the system will not validate IP addresses for incoming packets. The services are the system applications listed in the Service Control List beside ICMP. Click the Add button to display the following.
8.7 Update Software This option allows for firmware upgrades from a locally stored file. STEP 1: Obtain an updated software image file from your ISP. STEP 2: Select the configuration from the drop-down menu. Configuration options: No change – upgrade software directly. Erase current config – If the router has save_default configuration, this option will erase the current configuration and restore to save_default configuration after software upgrade.
8.8 Reboot To save the current configuration and reboot the router, click Save/Reboot. NOTE: You may need to close the browser window and wait for 2 minutes before reopening it. It may also be necessary, to reset your PC IP configuration.
Chapter 9 Logout To log out from the device simply click the following icon located at the top of your screen. When the following window pops up, click the OK button to exit the router. Upon successful exit, the following message will be displayed.
Appendix A - Firewall STATEFUL PACKET INSPECTION Refers to an architecture, where the firewall keeps track of packets on each connection traversing all its interfaces and makes sure they are valid. This is in contrast to static packet filtering which only examines a packet based on the information in the packet header. DENIAL OF SERVICE ATTACK Is an incident in which a user or organization is deprived of the services of a resource they would normally expect to have.
Example 1: Filter Name Protocol Policy Source IP Address Source Subnet Mask Source Port Dest. IP Address Dest. Subnet Mask Dest. Port Selected WAN interface : : : : : : : : : : In_Filter1 TCP Allow 210.168.219.45 255.255.0.0 80 NA NA NA br0 This filter will ACCEPT all TCP packets coming from WAN interface “br0” with IP Address/Subnet Mask 210.168.219.45/16 with a source port of 80, irrespective of the destination. All other incoming packets on this interface are DROPPED.
DAYTIME PARENTAL CONTROL This feature restricts access of a selected LAN device to an outside Network through the NexusLink 3112u , as per chosen days of the week and the chosen times. Example: User Name Browser's MAC Address Days of the Week Start Blocking Time End Blocking Time : : : : : FilterJohn 00:25:46:78:63:21 Mon, Wed, Fri 14:00 18:00 With this rule, a LAN device with MAC Address of 00:25:46:78:63:21 will have no access to the WAN on Mondays, Wednesdays, and Fridays, from 2pm to 6pm.
Appendix B - Pin Assignments ETHERNET Ports (RJ45) ETHERNET LAN Ports (10/100Base-T) Table 1 Pin Definition Pin Definition 1 Transmit data+ 5 NC 2 Transmit data- 6 Receive data- 3 Receive data+ 7 NC 4 NC 8 NC Signals for ETHERNET WAN port (10/1001000Base-T) Table 2 Pin Signal name Signal definition 1 TRD+(0) Transmit/Receive data 0 (positive lead) 2 TRD-(0) Transmit/Receive data 0 (negative lead) 3 TRD+(1) Transmit/Receive data 1 (positive lead) 4 TRD+(2) Transmit/Receive d
Appendix C – Specifications Hardware Interface RJ-14 X1 for Multi DSL Bonded, RJ-45 X 3 for LAN (10/100 Base-T), RJ-45 X 1 for GB Port, (10/100/1000 BaseT auto-sense), Reset Button X 1, WPS/WiFi on/off button x1, Power Switch X 1, Wi-Fi Antennas X 2, USB Host Dual WAN Interface VDSL2 .........Comply with G.993.2 (supporting profile 8a, 8b, 8c, 8d, 12a, 12b, 17a) VDSL2 bonded: up to 17a profile G.998.2 (VDSL2 Bonded) ADSL2+ …….. Comply with ITU-T G.992.5, ITU-T G.992.3, Annex A/L/M G.998.
Management Compliant with TR-069/TR-098/TR-104/TR-111 remote management protocols, Telnet, Web-based management, Configuration backup and restoration, Software upgrade via HTTP / TFTP / FTP server Bridge Functions Transparent bridging and learning ............Yes VLAN support ........................................Yes Spanning Tree Algorithm .........................Yes IGMP Proxy ...........................................
Appendix D - SSH Client Unlike Microsoft Windows, Linux OS has a ssh client included. For Windows users, there is a public domain one called “putty” that can be downloaded from here: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html To access the ssh client you must first enable SSH access for the LAN or WAN from the Management Access Control Services menu in the web user interface. To access the router using the Linux ssh client For LAN access, type: ssh -l root 192.168.1.
Appendix E - Connection Setup Creating a WAN connection is a two-stage process. 1 - Setup a Layer 2 Interface (ATM, PTM or Ethernet). 2 - Add a WAN connection to the Layer 2 Interface. The following sections describe each stage in turn. E1 ~ Layer 2 Interfaces Every layer2 interface operates in Multi-Service Connection (VLAN MUX) mode, which supports multiple connections over a single interface. Note that PPPoA and IPoA connection types are not supported for Ethernet WAN interfaces.
Heading Description Interface WAN interface name.
There are many settings here including: VPI/VCI, DSL Latency, DSL Link Type, Encapsulation Mode, Service Category, Connection Mode and Quality of Service. Here are the available encapsulations for each xDSL Link Type: EoA- LLC/SNAP-BRIDGING, VC/MUX PPPoA- VC/MUX, LLC/ENCAPSULATION IPoA- LLC/SNAP-ROUTING, VC MUX STEP 3: Click Apply/Save to confirm your choices. On the next screen, check that the ATM interface is added to the list.
To add a WAN connection go to E2 ~ WAN Connections WAN Connections.
E1.2 PTM Interfaces Follow these procedures to configure a PTM interface. NOTE: The NexusLink 3112u supports up to four PTM interfaces. STEP 4: Go to Basic Setup drop-down menu. WAN Setup Select PTM Interface from the This table is provided here for ease of reference. Heading Description Interface WAN interface name. DSL Latency {Path0} portID = 0 {Path1} port ID = 1 {Path0&1} port ID = 4 PTM Priority Normal or High Priority (Preemption).
NOTE: To add WAN connections to one interface type, you must delete existing connections from the other interface type using the remove button. There are many settings that can be configured here including: DSL Latency, PTM Priority, Connection Mode and Quality of Service. STEP 6: Click Apply/Save to confirm your choices. On the next screen, check that the PTM interface is added to the list. For example, an PTM interface in Default Mode is shown below.
E1.3 ETHERNET Interfaces Follow these procedures to configure a PTM interface. WAN Setup Select ETHERNET Interface STEP 1: Go to Basic Setup from the drop-down menu. This table is provided here for ease of reference. Heading Description Interface/ (Name) WAN interface name. Connection Mode Default Mode – Single service over one interface. Vlan Mux Mode – Multiple Vlan services over one interface. Remove Select interfaces to remove. STEP 2: Click Add to proceed to the next screen.
STEP 3: Select an Ethernet port and Click Apply/Save to confirm your choices. On the next screen, check that the ETHERNET interface is added to the list.
E2 ~ WAN Connections The NexusLink 3112u supports one WAN connection for each interface, up to a maximum of 16 connections. To setup a WAN connection follow these instructions. STEP 1: Go to Basic Setup WAN Setup. STEP 2: Click Add to create a WAN connection. The following screen will display.
STEP 3: Choose a layer 2 interface from the drop-down box and click Next. The WAN Service Configuration screen will display as shown below. NOTE: The WAN services shown here are those supported by the layer 2 interface you selected in the previous step. If you wish to change your selection click the Back button and select a different layer 2 interface. STEP 4: For VLAN Mux Connections only, you must enter Priority & VLAN ID tags.
E2.1 PPP over ETHERNET (PPPoE) STEP 1: Select the PPP over Ethernet radio button and click Next. You can also enable IPv6 by ticking the checkbox at the bottom of this screen. STEP 2: On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step.
The settings shown above are described below. PPP SETTINGS The PPP Username, PPP password and the PPPoE Service Name entries are dependent on the particular requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length. For Authentication Method, choose from AUTO, PAP, CHAP, and MSCHAP.
ENABLE FULLCONE NAT This option becomes available when NAT is enabled. Known as one-to-one NAT, all requests from the same internal IP address and port are mapped to the same external IP address and port. An external host can send a packet to the internal host, by sending a packet to the mapped external address. DIAL ON DEMAND The NexusLink 3112u can be configured to disconnect if there is no activity for a period of time by selecting the Dial on demand checkbox .
FIXED MTU Maximum Transmission Unit. The size (in bytes) of largest protocol data unit which the layer can pass onwards. This value is 1500 for PPPoA. ENABLE PPP DEBUG MODE When this option is selected, the system will put more PPP connection information into the system log. This is for debugging errors and not for normal usage. BRIDGE PPPOE FRAMES BETWEEN WAN AND LOCAL PORTS (This option is hidden when PPP IP Extension is enabled) When Enabled, this creates local PPPoE connections to the WAN side.
Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. Click Next to continue or click Back to return to the previous step. STEP 5: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them.
After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot. Go to Management Reboot and click Reboot.
E2.2 IP over ETHERNET (IPoE) STEP 1: *Select the IP over Ethernet radio button and click Next. * For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID. STEP 2: The WAN IP settings screen provides access to the DHCP server settings. You can select the Obtain an IP address automatically radio button to enable DHCP (use the DHCP Options only if necessary).
NOTE: If IPv6 networking is enabled, an additional set of instructions, radio buttons, and text entry boxes will appear at the bottom of the screen. These configuration options are quite similar to those for IPv4 networks. Click Next to continue or click Back to return to the previous step. STEP 3: This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox . Click Next to continue or click Back to return to the previous step.
ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox . The NAT submenu will appear in the Advanced Setup menu after reboot. On the other hand, if a private IP address is not used on the LAN side (i.e. the LAN side is using a public IP), this checkbox should not be selected, so as to free up system resources for improved performance. ENABLE FULLCONE NAT This option becomes available when NAT is enabled.
STEP 5: Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. If IPv6 is enabled, an additional set of options will be shown. IPv6: Select the configured WAN interface for IPv6 DNS server information OR enter the static IPv6 DNS server Addresses.
Note that selecting a WAN interface for IPv6 DNS server will enable DHCPv6 Client on that interface. Click Next to continue or click Back to return to the previous step. STEP 6: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot. Go to Management Reboot and click Reboot.
E2.3 Bridging NOTE: This connection type is not available on the Ethernet WAN interface. STEP 1: *Select the Bridging radio button and click Next. * For tagged service, enter valid 802.1P Priority and 802.1Q VLAN ID. For untagged service, set -1 to both 802.1P Priority and 802.1Q VLAN ID. STEP 2: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to return to the previous screen.
After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot. Go to Management Reboot and click Reboot. NOTE: If this bridge connection is your only WAN service, the NexusLink 3112u will be inaccessible for remote management or technical support from the WAN.
E2.4 PPP over ATM (PPPoA) STEP 1: Click Next to continue. STEP 2: On the next screen, enter the PPP settings as provided by your ISP. Click Next to continue or click Back to return to the previous step.
PPP SETTINGS The PPP username and password are dependent on the requirements of the ISP. The user name can be a maximum of 256 characters and the password a maximum of 32 characters in length. (Authentication Method: AUTO, PAP, CHAP, or MSCHAP.
KEEP ALIVE INTERVAL This option configures the interval between each PPP LCP request and the amount of time to wait for the PPP server to reply to the LCP request. If the time expired on all requests, the current PPP session would be dropped. ENABLE FULLCONE NAT This option becomes available when NAT is enabled. Known as one-to-one NAT, all requests from the same internal IP address and port are mapped to the same external IP address and port.
USE STATIC IPv4 ADDRESS Unless your service provider specially requires it, do not select this checkbox . If selected, enter the static IP address in the IP Address field. Also, don’t forget to adjust the IP configuration to Static IP Mode as described in section 3.2. Fixed MTU Fixed Maximum Transmission Unit. The size (in bytes) of largest protocol data unit which the layer can pass onwards. This value is 1500 for PPPoA.
Click Next to continue or click Back to return to the previous step. STEP 5: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot. Go to Management Reboot and click Reboot.
E2.5 IP over ATM (IPoA) STEP 1: Click Next to continue. STEP 2: Enter the WAN IP settings provided by your ISP. Click Next to continue. STEP 3: This screen provides access to NAT, Firewall and IGMP Multicast settings. Enable each by selecting the appropriate checkbox . Click Next to continue or click Back to return to the previous step.
ENABLE NAT If the LAN is configured with a private IP address, the user should select this checkbox . The NAT submenu will appear in the Advanced Setup menu after reboot. On the other hand, if a private IP address is not used on the LAN side (i.e. the LAN side is using a public IP), this checkbox should not be selected, so as to free up system resources for improved performance. ENABLE FULLCONE NAT This option becomes available when NAT is enabled.
STEP 4: Choose an interface to be the default gateway. Click Next to continue or click Back to return to the previous step. NOTE: If the DHCP server is not enabled on another WAN interface then the following notification will be shown before the next screen. STEP 5: Choose an interface to be the default gateway.
Click Next to continue or click Back to return to the previous step. STEP 6: The WAN Setup - Summary screen shows a preview of the WAN service you have configured. Check these settings and click Apply/Save if they are correct, or click Back to modify them. After clicking Apply/Save, the new service should appear on the main screen. To activate it you must reboot. Go to Management Reboot and click Reboot.
Appendix F - WPS OPERATION This Section shows the basic AP WPS Operation procedure. F1 Add Enrollee with Pin Method 1) Select Enabled from the Enable WPS dropdown menu. 2) Click the Apply/Save button at the bottom of the screen.
4) Operate Station to start WPS Adding Enrollee. F2 Add Enrollee with PBC Method 1) Press the WPS button on the front of the device to activate WPS PBC operation. 2) Operate Station (your dongle for example) to start WPS Adding Enrollee.
F3 – Configure WPS External Registrar Follow these steps to add an external registrar using the web user interface (WUI) on a personal computer running the Windows 7 operating system: Step 1: Enable UPnP on the Advanced Setup LAN screen in the WUI. NOTE: A PVC must exist to see this option. Step 2: Open the Network folder and look for the BroadcomAP icon.
Step 3: On the Wireless Security screen, enable WSC by selecting Enabled from the drop down list box and set the WPS AP Mode to Unconfigured. Step 4: Click the Apply/Save button at the bottom of the screen. The screen will go blank while the router applies the new Wireless settings.
Step 5: Now return to the Network folder and click the BroadcomAP icon. A dialog box will appear asking for the Device PIN number. Enter the Device PIN as shown on the Wireless Security screen. Click Next. Step 6: Windows 7 will attempt to configure the wireless security settings. Step 7: If successful, the security settings will match those in Windows 7.
Appendix G - Printer Server These steps explain the procedure for enabling the Printer Server. NOTE: This function only applies to models with an USB host port. STEP 1: Enable Print Server from Web User Interface. Select Enable on-board print server checkbox and enter Printer name and Make and model NOTE: The Printer name can be any text string up to 40 characters. The Make and model can be any text string up to 128 characters.
STEP 2: Go to the Printers and Faxes application in the Control Panel and select the Add a printer function (as located on the side menu below). STEP 3: Click Next to continue when you see the dialog box below.
STEP 4: Select Network Printer and click Next. STEP 5: Select Connect to a printer on the Internet and enter your printer link. (e.g. http://192.168.1.1:631/printers/hp3845) and click Next. NOTE: The printer name must be the same name entered in the ADSL modem WEB UI “printer server setting” as in step 1.
STEP 6: Click Have Disk and insert the printer driver CD. STEP 7: Select driver file directory on CD-ROM and click OK.
STEP 8: Once the printer name appears, click OK. STEP 9: Choose Yes or No for default printer setting and click Next.
STEP 10: Click Finish.
STEP 11: Check the status of printer from Windows Control Panel, printer window. Status should show as Ready.
