User's Manual

ManualsBrandsComputime ManualsElectronicsRemote Control Receiver (350MHz Receiver)

RCBHC

VARIABLE FLAME REMOTE CONTROL

INSTALLATION AND OPERATING INSTRUC-

TIONS FOR

CONCENTRIC VARITAP, LATCHTAP

AND MAXTROL VALVES

This remote control system provides a safe, reliable, and user-

friendly remote control for Concentric Varitap, latchtap and max-

itrol valve gas appliances. The system can be manually turned

On/Off or can remotely control the flame adjustment. Always

check with the home owner’s manual of the appliance for addi-

tional information, or warnings regarding accessory installation

before connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts

are missing or damaged, immediately contact the dealer from

whom you purchased the kit. Do not attempt to install any part of

the kit unless all parts are in good condition. Please keep this

booklet for future reference.

CONTENTS OF KIT

Description Qty

Transmitter 1

Battery Alkaline AAA ( for Transmitter) 3

Receiver (Assembly) consists of : 1

Receiver Box

Battery Door Black

Slide Button-Black (On/RS/Off) 1

Battery Alkaline AA (for Receiver) 4

Velcro (Loop and Hook) 1

Plug-In Wiring Assembly – 22” Inches 1

Installation Instructions 1

FEATURES/SPECIFICATIONS

• Battery Powered Transmitter and Receiver

• Easy Access Front Battery Door

• Pre-Programmed for Quick Installation

• 16 Security Codes

• Optional 6 hour shutdown

• Quick Disconnect Wiring Assembly

WARNING

Important Safety Information

• Read this manual thoroughly prior to installing, programming

or operating this remote control system.

• This remote control system is designed for use with a

Concentric varitap, latchtap and maxtrol gas valve system.

Do not use this remote control system on appliances with

other types of gas valve.

• This remote control system requires three (3) “AAA” and four

(4) “AA” alkaline batteries to power the transmitter and

receiver respectively. Wiring must conform to appliance

requirement and building codes/ordinances as required by

local and national code authorities having jurisdiction in your

area.

• This remote control system should only be used as described

in this manual and any other use is not recommended and will

void the warranty.

Turn appliance OFF and allow to cool before

installing or servicing. DO NOT connect

110-120 VAC wiring to the gas control valve. The

remote control system must be installed exactly as

outlined in these instructions. Read all

instructions completely before attempting

installation and follow instructions carefully

during installation. Any modification of

components or failure to follow instructions

exactly will void the warranty and may cause a

fire hazard.

INSTALLATIONS

Remote Receiver:

The remote receiver may be wall mounted or installed in the appli-

ance per the appliance homeowner’s manual. Refer to the

Homeowner’s Manual for special installation instructions.

Failure to follow the installation instructions found in the appro-

priate Homeowner’s Manual will void the warranty and may cause

a fire hazard.

Installing Batteries:

The remote receiver uses four (4) “AA”- size batteries. To install

batteries,

1.Open the battery door by

pressing the two tabs located

on the door.

2.Install the batteries as

indicated on the receiver door.

3.Gently, close the battery door

until the door tab snaps in

place.

4.Install the receiver into the

appliance, refer to the

Homeowner’s Manual of

appliance for installation

instructions.

5.The batteries should be

replaced at least once every 6

months or when the battery

indicator light flashes, slowly

and periodically red.

Installing Wire:

This system comes with an 22 inch pre-assembled wire assembly.

Insert the four-pin black terminal wire into the back of the receiv-

er. The terminal wire block can only be installed one way and do

not force the terminal plug into the receiver.

Follow the homeowner’s manual for connecting the two (2) 1/4”

female spade terminals to the gas valve. Make sure that the color

of valve wires matches the color tag of the wiring from receiver,

exception with the Concentric latchtap wires are reversed in color.

Please refer to the following diagram for wiring directions.

If valve operates in reverse direction, simply reverse the wires and

valve should operate correctly.

For applications longer than 22 inches, use 18 gauge wire, 105ºC

rated, with no splices by using the approiate connectors. Connect

to the two (2) 1/4“ female spade wiring terminals and wire can be

no longer than 20 feet.

Make sure that the wires do not contact the

appliances any place other than at the terminals.

Exposure to temperatures higher than 105ºC

(250ºF) may cause the receiver to malfunction

and/or cause a fire hazard..

If you connect wires wrong, the valve will operate

in the wrong direction.

For Latchtap valve only. Wires are reversed in

color. The tagged red wire must be connected to

the black wire from the valve.

Remote Transmitter

Installing Batteries:

The remote transmitter uses three (3) “AAA”- size batteries. To

install batteries,

1.Press down the battery door tab

and pull out to remove the

battery door.

2.Install the batteries as indicated

in the battery compartment.

3.Gently, close the battery door

by snapping in place.

4.The batteries should be

replaced at least once every 6

months or when the battery

indicator is displayed on LCD

screen.

Setting Privacy (DIP) Switch on Receiver and Transmitter:

The remote receiver and transmitter privacy (DIP) switches are

preset at the factory. In the event of activation or interference

from other nearby transmissions, reset the code using the follow-

ing procedure:

1.Remove battery cover door from transmitter & pry up small

rectangle on top of receiver to view DIP switches.

2.Slide the DIP switches on the transmitter and receiver to your

choice of ON or OFF position. Switches #1, #2, #3 and #4 are

preset to “ON” for both the transmitter and receiver.

3.The switches on the transmitter and receiver must match exactly

in order for the system to work.

4.The system is now ready to operate.

See Optional Auto Shutdown.

WARNING

NOTE

Back of the Transmitter

Battery

Door

Ta b

DIP

DIPON

Concentric

VaritapValve

Concentric

LatchtapValve

Maxitol Valve

Summary of content (2 pages)

PAGE 1
RCBHC INSTALLATIONS This remote control system provides a safe, reliable, and userfriendly remote control for Concentric Varitap, latchtap and maxitrol valve gas appliances. The system can be manually turned On/Off or can remotely control the flame adjustment. Always check with the home owner’s manual of the appliance for additional information, or warnings regarding accessory installation before connecting this remote control system. Carefully inspect the contents for shipping damage.
PAGE 2
OPERATIONS: Transmitter: General: The RCBHC is an On/Off and High/Low remote control. The transmitter will operate the remote receiver from 1 foot to a maximum of 30 feet. The operational range is reduced when batteries are low or when the receiver is located inside a metal enclosure. Initial start up: Follow the homeowner installation instruction for the proper lighting of the pilot and appliance. After initial power up, the transmitter is ready for use.