ZigBee-Ready RF Transceiver Module (IEEE 802.15.4) CTL3576/7/8/9 The reproduction of this datasheet is NOT allowed without approval of Computime Limited. All information and data contained in this datasheet are subject to change without notice. This publication supersedes and replaces all information previously supplied. Computime has no responsibility to the consequence of using the information described in this document. Copyright © 2011 Computime Limited. All rights reserved. Rev.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 Revision Rev. Date (DD-MM-YYYY) 1 18-09-2011 History First Release Copyright © 2011 Computime Limited. All rights reserved. Rev.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 Table of Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. General Description...................................................................................................................................... 0 Applications .................................................................................................................................................. 0 Features ....................................................................
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 1. General Description The CTL357x RF Transceiver Module is compact surface mounted Module specially designed for Ember ZigBee™ protocol stack for wireless networks, EmberZNet, based on IEEE 802.15.4 standard in the 2.4GHz world-wide ISM band. The complete module is only 32.4 x 25.4 x 4.1 mm. It integrated a 2.4GHz, IEEE 802.15.4-2003 compliant transceiver with a 32-bit network processor (ARM Cortex-M3 Processor) to run EmberZNet.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 4. Absolute Maximum Ratings Parameter Test Conditions Regulator input voltage (VDD_PADS) RF Input Power (for max level for correct packet reception) Min. -0.3 RX signal into a lossless balun Max. Unit +3.6 V +15 dBm Voltage on any GPIO (PA[7:0], PB[7:0], PC[7:0]), SWCLK, nRESET, VREG_OUT -0.3 VDD_PADS +0.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 Parameter Condition / Note Min Sensitivity PER = 1% PER, 20byte packet defined by IEEE 802.15.4 Boost mode -98 dBm Adjacent channel rejection +/-5 MHz IEEE 802.15.4 compliance at -82 dBm 35/35 dB Adjacent channel rejection +/-10 MHz IEEE 802.15.4 compliance at -82 dBm 40/40 dB -6 dB Co-channel rejection Supply voltage Typ. 2.7 Max 3.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 7. Typical application block HOST MCU VDD_PADS=2.7- 3.6V 32.768kHz NREST PTI_EN Debug and PTI-DATA programming SIF_CLK interface SIF-MISO 8Mb flash CTL357x RF Module 24MHz SIF-MOSI NSIF LOAD LINK_ACTIVITY Figure 1: Example of application circuit 8. Pin Assignment Figure 2: CTL357x pin assignment Copyright © 2011 Computime Limited. All rights reserved. Rev.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 9.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 7 Pin# IRQC IRQC IRQC IRQC I Default external source C interrupt TIM1C2 TIM1C2 TIM1C2 TIM1C2 O Timer 1 channel 2 output TIM1C2 TIM1C2 TIM1C2 TIM1C2 1 Timer 1 channel 2 input PB6 PB6 PB6 PB6 I/O High current Digital I/O ADC1 ADC1 ADC1 ADC1 Analog ADC input 1 IRQB IRQB IRQB IRQB I External interrupt source B TIM1C1 TIM1C1 TIM1C1 TIM1C1 O Timer 1 channel 1 output TIM1C1 TIM1C1 TIM1C1 TIM1C1 I Timer 1 channel 1
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 Digital I/O PB3 PB3 PB3 PB3 I/O TIM2C3 TIM2C3 TIM2C3 TIM2C3 O Timer 2 channel 3 output TIM2C3 TIM2C3 TIM2C3 TIM2C3 I Timer 2 channel 3 input SC1nCTS SC1nCTS SC1nCTS SC1nCTS I UART CTS handshake of Serial Controller 1 SC1SCLK SC1SCLK SC1SCLK SC1SCLK O SPI master clock of serial Controller 1 SC1SCLK SC1SCLK SC1SCLK SC1SCLK I SPI slave clock of serial Controller 1 GND GND GND GND PC6 PC6 PC6 PC6 I/O Digital I/O OSC3
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 TIM2C1 TIM2C1 TIM2C1 TIM2C1 O Timer 2 channel 1 output TIM2C1 TIM2C1 TIM2C1 TIM2C1 I Timer 2 channel 1 input SC2MOSI SC2MOSI SC2MOSI SC2MOSI O SPI master data out of serial controller 2 SC2MOSI SC2MOSI SC2MOSI SC2MOSI I SPI slave data in of serial controller 2 SI I Serial data in fot the 8Mb flash④ SI 19 PA1 PA1 PA1 I/O TIM2C3 TIM2C3 TIM2C3 TIM2C3 O Timer 2 channel 3 output TIM2C3 TIM2C3 TIM2C3 TIM2C3 I Timer 2 cha
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 SC2SCLK SC2SCLK SC2SCLK SC2SCLK I SPI slave clock of serial controller 2 SCK I Clock in for the 8Mb flash SCK 21 22 Pin# PA6 PA6 PA6 PA6 I/O High current TIM1C3 TIM1C3 TIM1C3 TIM1C3 O Timer 1 channel 3 output TIM1C3 TIM1C3 TIM1C3 TIM1C3 I Timer 1 channel 3 input PB4 PB4 PB4 PB4 I/O TIM2C4 TIM2C4 TIM2C4 TIM2C4 O Timer 2 channel 4 output TIM2C4 TIM2C4 TIM2C4 TIM2C4 i Timer 2 channel 4 input SC1nRTS SC1nRTS SC1nR
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 ADC4 ADC4 ADC4 ADC4 Analog PTI_EN PTI_EN PTI_EN PTI_EN O Frame signal of packet trace interface O Synchronous CPU trace data bit 2 TRACEDATA2 TRACEDATA2 TRACEDATA2 TRACEDATA2 25 26 Pin# 27 ADC input 4 Digital I/O PA5 PA5 PA5 PA5 I/O ADC5 ADC5 ADC5 ADC5 Analog PTI_DATA PTI_DATA PTI_DATA PTI_DATA O Data signal of packet trace interface NBOOTMODE NBOOTMODE NBOOTMODE NBOOTMODE I Embedded serial bootloader activation out of re
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 SC1MISO SC1MISO SC1MISO SC1MISO I SPI master data in of serial controller 1 SC1MOSI SC1MOSI SC1MOSI SC1MOSI I SPI slave data in of serial controller 1 SC1SCL SC1SCL SC1SCL SC1SCL I/O SC1RXD SC1RXD SC1RXD SC1RXD I UART receive data of serial controller 1 TIM2C2 TIM2C2 TIM2C2 TIM2C2 O Timer 2 channel 2 output TIM2C2 TIM2C2 TIM2C2 TIM2C2 I Timer 2 channel 2 input PB5 PB5 PB5 PB5 I/O ADC0 ADC0 ADC0 ADC0 Analog TIM2CLK
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 10. Block Diagram 2.7 – 3.6V PCB antenna 32 Bit ARM Processor 24MHz User Application TO HOST MCU IEEE 802.15.4 RF Transceiver TM Zigbee Network FEM IEEE 802.15.4 MAC CTL3576 2.7 – 3.6V PCB antenna 32 Bit ARM Processor User Application TO HOST MCU 8Mb flash 24MHz FEM TM Zigbee Network IEEE 802.15.4 RF Transceiver IEEE 802.15.4 MAC CTL3577 Copyright © 2011 Computime Limited. All rights reserved. Rev.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 2.7 – 3.6V PCB antenna 32 Bit ARM Processor 24MHz User Application TO HOST MCU 32.768kHz FEM ZigbeeTM Network IEEE 802.15.4 RF Transceiver IEEE 802.15.4 MAC CTL3578 2.7 – 3.6V PCB antenna 32 Bit ARM Processor 8Mb flash 32.768kHz User Application TO HOST MCU 24MHz FEM TM Zigbee Network IEEE 802.15.4 RF Transceiver IEEE 802.15.4 MAC CTL3579 Figure 3: Block Diagram 11.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 15 2425MHz 16 2430MHz 17 2435MHz 18 2440MHz 19 2445MHz 20 2450MHz 21 2455MHz 22 2460MHz 23 2465MHz 24 2470MHz 25 2475MHz 26 2480MHz Note: the output power of EM357 should be configured lower than -15dBm for 2480M channel to Comply FCC requirement. The use of RF frequencies and maximum allowed RF power should according to different national regulations. The CTL3576 is complying with the applicable regulations for the world wide 2.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 13. Mechanical Dimensions Figure 5: Mechanical Dimensions of CTL3576 .8 Pin 1 Pin 11 For further details on the SoC transceiver (Ember EM357), please consult the data sheet at http://www.ember.com Copyright © 2011 Computime Limited. All rights reserved. Rev.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 14. Modules Differentia Computime Model No. CTL3576 CTL3577 CTL3578 CTL3579 P.A. Y Y Y Y 32kHz Crystal N N Y Y Copyright © 2011 Computime Limited. All rights reserved. 8Mbit Flash Memory N Y N Y Rev.
FCC STATEMENT: 1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
(1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.
ZigBee- Ready RF Transceiver Module CTL3576/7/8/9 Contact information COMPUTIME CORPORATE HQ 17/F, Great Eagle Centre, 23 Harbour Road, Wanchai, Tel: +852.2260.0300 Fax: +852.2790.3996 e-mail: hq@computime.com COMPUTIME NORTH AMERICA HQ, 4700 Duke Dr. Suite 200 Mason OH 45040 USA Tel: +1(513).398.2579 Fax: +1(513).754.8955 e-mail: na@computime.com CINCINNATI WIRELESS SOLUTIONS LTD 4700 Duke Dr. Suite 200 Mason OH 45040 USA Tel: +1(513).754.8935 Fax: +1(513).754.8955 e-mail: ctws@computime.
