Network RFID Encoder Installation and Operation Instructions Pg. 1 of 13 Network RFID Encoder Installation and Operation Instructions FCC Warning: Changes or modifications not expressly approved by Computerized Security Systems could void the user’s authority to operate the equipment. All information contained herein, including but not limited to product pricing and other intellectual property, is confidential and intended for the sole use of the addressee(s) so named.
Network RFID Encoder Installation and Operation Instructions Pg. 2 of 13 Table of Contents Setting Up the Encoder 3 Setup for TCP/IP Connection with System 6000 4 Setup for RS232 (serial) Connection with System 6000 7 Setup for USB Connection with System 6000 8 Encoding a Keycard or RFID Credential 10 Interrogating a Keycard or RFID Credential 12 © SAFLOK™, all rights reserved.
Network RFID Encoder Installation and Operation Instructions Pg. 3 of 13 Setting Up the Encoder 1. Connect the power cable to the encoder (located on the back of the unit, as shown in Fig. 1). Use a SAFLOK 12V DC power supply, part number 73763. 2. Connect the communication cable to the appropriate communication port on the back of the encoder Ethernet network (TCP/IP), DeskLinc serial port (RS232), or PC (USB). 3. Plug in SAFLOK power supply to an electrical outlet. 4.
Network RFID Encoder Installation and Operation Instructions Pg. 4 of 13 Setup for TCP/IP Connection with System 6000 1. Logon to the CRS at any computer on the network, a TCP/IP encoder can be added from any CRS because it is not directly connected to the computer. 2. Click the Settings tab then click the Add button under station ID assignments for entire SAFLOK system. Type in the Station ID#, the Port will default to 5264 and should not be changed.
Network RFID Encoder Installation and Operation Instructions Pg. 5 of 13 Setup for TCP/IP Connection with System 6000 (continued) 4. When the MAC address appears on the screen double click on it and it will move it up to the MAC Address input line. Click Configure to send the information to the encoder. 5. When encoder receives the information the message above will appear. Click OK. Reset the power to the encoder for changes to take effect. Then click Close. 6.
Network RFID Encoder Installation and Operation Instructions Pg. 6 of 13 Setup for TCP/IP Connection with System 6000 (continued) 7. Click OK. 8. Click OK to add the Station ID to system. 9. Now the Station ID will appear in the assignments for the entire SAFLOK System and can be added or changed in the CRS at any computer on the network. © SAFLOK™, all rights reserved.
Network RFID Encoder Installation and Operation Instructions Pg. 7 of 13 Setup for RS232 (serial) Connection with DeskLinc™ 1. Connect the RS232 cable to the encoder (see Fig. 2) and the hand-held terminal. The thin 90-degree plug inserts into the top side of the hand-held terminal the other end plugs into the back of the encoder unit. RS232 Connection Fig. 2 2. Plug the power supplies for the hand-held terminal and encoder into a wall socket. 3.
Network RFID Encoder Installation and Operation Instructions Pg. 8 of 13 Setup for USB Connection with System 6000 1. Log on to the Com Request Server (CRS) at the computer the encoder will be attached to. Note: The encoder can be added from only the CRS on the computer that the encoder is attached to because the encoder is directly connected to that computer. 2. Click the Settings tab, then click the Add button under “Station ID assignments for this computer”. 3.
Network RFID Encoder Installation and Operation Instructions Pg. 9 of 13 Setup for USB Connection with System 6000 (continued) 8. Click OK to add the Station ID to system. 9. At this point, the contactless smart card encoder is installed. You may now set it to be the default encoder in the SAFLOK Client program (System tab, then terminal settings). The Station ID will appear in both “Station Assignments for this computer” and the “Station ID Assignments for the Entire System” sections in the CRS.
Network RFID Encoder Installation and Operation Instructions Pg. 10 of 13 Encoding a Keycard or RFID Credential 1. To encode a keycard, open the SAFLOK Client program. Enter your User ID and Password to log on, then click OK. 2. At the main screen, click on the Keys tab. 3. Click the appropriate Make Keys button (e.g., Make User Keys, Make Display Keys, etc.) for the keycard you are making. 4. Following the procedure to make a key, enter the appropriate information and make the appropriate selections.
Network RFID Encoder Installation and Operation Instructions Pg. 11 of 13 Interrogating a Keycard or Credential 1. To interrogate a keycard, open the SAFLOK Client program. Enter your User ID and Password to log on, then click OK. 2. At the main screen, click the Keys tab. 3. Click the Interrogate User Key button. 4. Click Yes if you would like to read log records off a Staff keycard. 5. Place the RFID credential on the RFID encoder when prompted by the system. © SAFLOK™, all rights reserved.
Network RFID Encoder Installation and Operation Instructions Pg. 12 of 13 Interrogating a RFID Keycard (continued) 6. The Information About the Key Read PC dialog box will appear. To view or print the report, click Report. 7. Check the box if you would like to see only locks that allowed the key to open the door. Click OK to proceed. 8. Select the Report Destination and Options. Click OK to continue. © SAFLOK™, all rights reserved.
Network RFID Encoder Installation and Operation Instructions Pg. 13 of 13 Interrogating a RFID Keycard (continued) Key Interrogation Report Example Class A Digital Device NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.