Installation guide

ManualsBrandsCompuSTAR ManualsRemote Control1WAMR-762

INSTALLATION GUIDE

By Firstech, Inc.

Website: www.compustar.org

TABLE OF CONTENTS

Wiring Diagram

A. Notes for Wire Connection……………………………………..……3

B. Dip Switch and Jumper Setting………………………...……...……4

C. Installation of Antennas and RPS (Remote Paging System)…....5

D. Option Program for Four Button Remotes………………………...5

E. Option Program for Six Button Remotes…………………………..6

F. Programming Options………………………………………………..6

G. Diagnostic Problems with Auto-Start……………………………….7

H. Limited Lifetime Consumer Warranty………………………………7

Summary of content (7 pages)

PAGE 1
INSTALLATION GUIDE By Firstech, Inc. Website: www.compustar.org TABLE OF CONTENTS Wiring Diagram A. Notes for Wire Connection… … … … … … … … … … … … … … ..… … 3 B. Dip Switch and Jumper Setting… … … … … … … … … ...… … ...… … 4 C. Installation of Antennas and RPS (Remote Paging System)… ....5 D. Option Program for Four Button Remotes… … … … … … … … … ...5 E. Option Program for Six Button Remotes… … … … … … … … … … ..6 F. Programming Options… … … … … … … … … … … … … … … … … … ..6 G.
PAGE 2
Wiring Diagram CN1 CN2 OFF/ ON DI P1 CN12 3 Cold Se nsor 4Whi te 5Vi ole t 6Ye llow 5: Anti -Gri nd 6: Starte r 7Gr/ Rd 8Black 7:I gni ti on 8: ( -) 1 Gr/ Wh ( -) L i ght 250m A 2 Bk ( -) Status 250m A 3 Gr ( -) I gni ti on 250m A 4 Wh/ Bk ( -) Acce ssory 250m A 5 Rd / Bk ( -) Starte r 250m A 1 Lt.Blue ( -) E-Brak e Se nsi ng 2 Gray/ Bk ( -) Hood Se nsi ng 3 Lt.
PAGE 3
A. Notes for Wire Connection 1. There are two 12 V Constant Wires in the CN1. One is to supply power to the CPU and ignition and the other is to supply power to Starter and Accessory. 2. Pre-wired Relay for Anti-Grind - Violet at CN1 supplies a negative 250mA output when the system is remote starting. The Yellow wire from 87a should go to the Starter Motor side. 3. Pre-wired Relay for 2nd Ignition, 2nd Starter or 2nd Accessory. You may select the relay’s trigger input from one of the three outputs of CN2.
PAGE 4
8. The sequence for the rearm pulse: (1) pulse when armed (locked), (2) pulse after Starter, and (3) pulse one second after remote start shut down. 9. The sequence for the disarm pulse: (1) pulse when disarmed (unlocked), (2) pulse before remote starting. 10. Learning Tach/Injector Wire: Start the vehicle with the key manually and let the engine idle down to a minimum. The next step is to press the black tachometer button. The car's lights will flash once to confirm the tach was learned.
PAGE 5
Important! Once you cut the Jumper Wire, you are not allowed to reconnect the wire. The reconnection will completely void the warranty. A trace of reconnection of this wire will prevent you from any claim whatsoever pertaining to the manual transmission mode. C. Installation of Antennas and RPS. The antennas have been calibrated for horizontal installation at the top-left corner of the windshield. Different installation may adversely affect the transmitting distance. D.
PAGE 6
E. Option Programming for Six Button Remotes The procedures will be the same as the 4 button remotes except the use of the different buttons. Programming Programming Menu 1 Programming Menu 2 Option Selection Factory Setting Option Selection Default Setting Selection 6 Button Remote (Trunk+Start)(Trunk+Stop)(Stop)Lock Unlock (Start)- 4 Button Remote (I+II)(I+IV)(IV) (I ) (II ) (III) F.
PAGE 7
Note: 2-1 Cold start mode requires installation of the optional temperature sensor. In the default factory setting, Cold Sensor input works as Remote Start Activation Input. A Ground pulse to this wire will start the vehicle 2-5 Automatic Transmission Vehicle: This programmable option enables your vehicle to automatically lock the doors upon starting the vehicle with a key. In addition, the vehicle will automatically unlock the doors upon pulling the key out from the ignition.