9078 plus 9078D plus User Manual Rev.
Compuprint Information Thanks for choosing the 9078/78D plus printer. Your printer is a reliable working equipment that will be very useful in your daily job. Our printers have been designed to be compact and respectful of the work environment. They offer a wide range of features and multiple functions that confirm the high technological level reached by the Compuprint S.p.A.
Compliance Statements FCC Compliance Statement (USA) This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Compliance Statement (Canada) This digital apparatus is in conformity with standard NMB-003 of Canada. Cet appareil numérique est conforme à la norme NMB-003 du Canada. Übereinstimmungserklärung (Deutschland) Bescheinigung des Herstellers/Importeurs: Hiermit wird bescheinigt, dass der Drucker der Maschinenlärminformationsverordnung 3. GSGV, 18.01.1991 entspricht: Der höchste Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN27779-1991.
International Compliance EN55022:1998 Emissions Series EN 61000-3-2:1995 Power line harmonics EN 61000-3-3:1995 Power line flicker EN55024:1998 Immunity Characteristics EN61000-4-2:1995 E.S.D. EN61000-4-3:1995 Radiated Susceptibility EN61000-4-4:1995 E.F.T EN61000-4-5:1995 Surge EN61000-4-6:1996 R.F.
Safety Information A. Never remove any printer cover unless it is necessary for the installation of a printer accessory and expressly described in this manual. B. Please retain the printer covers in a safe place because they should be reinstalled if you decide to remove any printer accessory.
Table of Contents Safety Information......................................................... iii Table of Contents.......................................................... iv Getting to Know Your Printer ....................................... 1 Printer Features..............................................................................1 Unpacking Your Printer.................................................................2 Printer Parts..................................................................
Getting to Know Your Printer Printer Features • 24 Needle Print Head • 136 columns • Draft printing at 700 cps, LQ printing at 133 cps • IBM Proprinter XL24E/XL24,Personal Printer 2391+ and EPSON LQ 1050-2550 emulations • Multiple copies (1 original and 7 copies) • Automatic paper path selection • Easy operability via operator panel menu and S/W commands • Optional Automatic Sheet Feeder (120 sheets capability) which handles cut sheets, multicopies and envelopes, accepts up to two additional paper bins and
Unpacking Your Printer Together with the Installation Guide and the CD-ROM with the User Manual, the following items are included in the box: Notify any damage to your supplier.
Printer Parts Front View 9078 plus model O pe ra tor P anel Pa pe r Kno b C u t Sheet Support Po w er S w itch Pu sh Tractor C over Pa pe r G u ides 3
9078D plus model O pe rator Panel Pa pe r Kn ob Pu sh Tracto rs C over Po w er Sw itch 4
Rear View R e ar Pap er S lo t Top C o ve r R e ar Tracto r Area C o ver Pa per K no b In te rfa ce C o nn ecto rs AS F A re a C ove r Po w er C ab le C o nn ecto r 5 R e ar Tracto r In sta lla tion Are a C ove rs
Setting Up Your Printer Choosing a Suitable Location Consider the following points when you choose the location for your printer: • The distance between the printer and the host computer must not exceed the length of the interface cable; • The location must horizontal and stable; be sturdy, • Your printer must not be exposed to direct sunlight, extreme heat, cold, dust or humidity (see "Printer Specifications" later); 80 cm 3 1 .5 in . 1 39 00 .4 cm in m 20 c in 7 .9 m 20 c in 7 .
Printer Assembly Removal of the Shipment Locks Open all the printer covers and make sure that you remove all the shipment locks from the printer.
Ribbon Cartridge Installation Two types of black ribbon cartridges are available for this printer, depending on whether the color kit is installed or not. Make sure that you are using only Compuprint original consumables. 1. Make sure that the printer is turned off. 2. Find the ribbon cartridge among the accessories.
3. Open the top cover using the small handles on either side of the top cover. 4. Turn the printer on. The print carriage prepares for ribbon cartridge installation.
5. Before installing the ribbon cartridge turn the ribbon winding knob in the arrow direction (located on the cartridge) to take up slack in the ribbon. R ib b on Ten sion K n ob To avoid damage to the ribbon, do not turn the winding knob in the wrong direction. 6. Align the cartridge pins with the locking grooves on the left and right cartridge supports. The cartridge (black “Long Life” or color) to be used when the color kit is installed has only one groove.
7. Slide and insert the ribbon guide between the print head and the ribbon guide mask holding it perpendicular to the print head. Make sure that the ribbon is inserted correctly between the print head and the print head mask. NO OK R ib b on G uide H o ld er for C olor K it If the color kit option is installed on your printer insert the white plastic holder onto the color kit as shown in the following figure.
8. Turn the ribbon winding knob in the arrow direction (located on the cartridge) to take up slack in the ribbon. R ib b on Ten sion Kn ob 9. Push the cartridge down gently until it clips into place at all four locking points. 10. Turn the ribbon winding knob again in the direction of the arrow to take up slack in the ribbon. 11. To ensure that the ribbon guide runs freely along the ribbon, manually move the print carriage horizontally.
Upper Push Tractor Installation (9078D plus model only) An additional push tractor is provided with the 9078D plus printer. This second push tractor unit can be installed in front position (on the lower push tractor). 1. Find the upper push tractor among the accessories. 2. Install the upper push tractor aligning both its hooks with the lower push tractor pins and inserting them into the corresponding pins. Push the upper tractor until it is fully engaged.
3. The upper push tractor must be installed as shown in figure. 4. If you need to remove the upper push tractor, turn the printer off. Take the connector cable off and press on the push buttons (located in the upper push tractor hooks) to disengage the tractor.
Host Computer Connection This printer can be connected to your host computer via two available interfaces. The interface connectors are located on the rear of the printer. • A bidirectional IEEE1284 parallel interface • A RS-232/C or RS-422/A serial interface Before connecting the interface cable, make sure that the printer and the host computer are turned OFF . Insert the parallel interface cable into the parallel connector and fasten it by means of the clips.
Software Driver Selection At this point it is necessary to configure your printer for your application package. The installation procedures depend upon the host environment. Follow the instructions in the readme file you find on the CD-ROM. In a WINDOWS 95/98/2000® environment the printer supports the Plug & Play feature. The printer drivers of all Compuprint printers can be found at the Internet Address http://www.compuprint.
Power Connection Make sure that the power outlet matches the power rating of the printer. See the name plate of the printer, that you find under the rear ASF cover. In case the power rating does not correspond DO NOT CONNECT THE PRINTER TO THE MAINS. Consult your dealer for help. 1. Make sure the power outlet is near the printer location and easily accessible. Always use a grounded outlet. 2. Make sure that the power switch is in 0 position (OFF).
3. Insert the power cable plug into the printer connector and the other power cable end into a convenient outlet (the figure shows the European version). 1 2 4. If you need to turn the printer on, press the power switch in the I position (ON).
Selecting the Display Language The display messages for this printer can be displayed in five different languages: English (Default), French, German, Italian and Spanish. To select the language, that you prefer, proceed as follows: 1. Press the PROGRAM key and keep it pressed while powering on the printer until the following message will be displayed: RELEASE KEY 2. When you release the PROGRAM key, the following messages will be displayed: 9078 plus 9078D plus or then, PRINT OUT? NO 3.
Configuring the Printer Operator Panel Presentation The operator panel enables you to perform many of the printer functions including paper path selections, font selection and the printer setup.
Display Messages The printer display is used to indicate the printer status or to request an user intervention and gives the following information: • when paper is already loaded and the • printer is off line (READY indicator unlit): M1 - Lower Push E C u rre n t M a cro when paper is already loaded and the printer is on line (READY indicator lit): M1 - Lower Push C u rre n t P a p er P a th C u rre n t E m ulatio n C u rre n t M a cro C u rre n t P a per P ath where: M1, M2, M3, M4 Indicate which o
• when there is no paper loaded and the • printer is off line (READY indicator unlit): M1 - Lower Push Load Lower Push C u rre n t M a cro C u rre n t P a p er P a th where: M1, M2, M3, M4 LOAD ASF1 LOAD ASF2 LOAD ASF3 LOAD LOWER PUSH LOAD UPPER PUSH LOAD LOW.PUSH&MF LOAD MANUAL FORM LOAD PSH-PLL&MF LOAD PUSH-PULL ASF1 ASF2 ASF3 LOWER PUSH UPPER PUSH PUSH-PULL LOW.
The following messages appear to indicate other printer conditions or user intervention requests. The list is in alphabetical order: Message COVER OPEN CLOSE COVER EJECTING LOAD ASF1 LOAD ASF2 LOAD ASF3 LOAD LOWER PUSH LOAD LOW.PUSH&MF LOAD MANUAL FORM LOAD PSH-PLL&MF LOAD PUSH-PULL LOAD UPPER PUSH LOCKED MENU MACRO MICRO MICRO OPER.
Message RELEASE KEY RESET & BREAK SELF TEST SHIFT FUNCTION TEAR IF NECESS. PARK PAPER TEAR IF NECESS. EJECT PAPER TEAR OFF PAPER PARK PAPER TEAR OFF PAPER EJECT PAPER UNLOCKED MENU Description This message is displayed when you can release the PROGRAM key in the Self-test selection or in the Power-on Configuration procedure. When the input buffer is cleared an a break (250 msec.) on a serial interface is sent pressing the PROGRAM and then the ON LINE keys. The printer is printing the self-test page.
Indicators R E ADY Lit when the printer can receive and print data (printer online). Blinks when there is data in the buffer and the printer is offline. Unlit, when the printer is disabled and the buffer does not contain any data, or during the initialization, setup or tests. PRO GRAM Blinks when one of the printer setup procedures has been selected: Program Configuration or Power-On Configuration. SHIFT Lit when the alternate function of the keys has been enabled pressing the SHIFT key.
Function Keys The function keys are enabled, when the printer is offline (READY indicator unlit). The function keys have three functions each. Normal Function The normal function of the keys does not require previous action to select it. This function is indicated in black characters beside the function keys. Shift Function The alternate function is selected pressing the SHIFT key. The alternate functions of the keys are described on the gray areas beside the keys.
ON LINE Key ON LINE Normal Function Program Function Enables or disables the printer. • If this key is pressed while powering the printer on, the self test is printed; the printout is stopped pressing this key again. • In an error condition, once the error cause has been removed, press this key to enable the printer. • If the Tear-Off Function in the Program Setup is set to Manual, press this key to position the paper for the Tear-Off.
SHIFT Key SHIFT Normal Function Enables the alternative key functions. If the printer is receiving print data, press the ON LINE key before pressing the SHIFT key. If no printing data are in the print buffer, pressing the SHIFT key, the printer goes offline. The display then shows SHIFT FUNCTION to indicate that the Shift Function of the keys is enabled. May be used to abort paper parking procedure. See also “How to Handle the Paper Parking”, later in this manual.
LF Key LF Normal Function Performs a line feed according to the current line spacing settings. ↓ Shift Function Moves the paper backward in microsteps. Keeping the key pressed the paper is moved continuously at increasing speed. ↓ Program Function Scrolls the setup and macro functions forward. MACRO Key MACRO PATH ← Normal Function Selects one of the user macros (Macro 1, Macro 2, Macro 3 or Macro 4).
Key Combinations PROGRAM + SHIFT Normal Function ONLINE + MACRO + SHIFT Normal Function When the printer is on line without printing or printing data (READY indicator lit) or when the printer is unable to receive and print data but there is still data in the input buffer (READY indicator blinks) press these two keys contemporaneously, the printing noise level toggles between normal (QUIET PRINT OFF) and reduced noise level (QUIET PRINT ON).
Printer Setups The main printer setup parameters can be selected via the operator panel. The setup parameters are divided into two printer setups, the Power-On Configuration, that allows a complete configuration at installation time according to the hardware and the emulation types, and the Program Setup, that allows you to set the functions that are the most useful in your daily job. This settings can be selected when the printer is online without printing or offline (READY indicator unlit).
Leaving the Printer Setups • Pressing the PROGRAM key in the Power-On Configuration the printer exits from the setup and the new settings will be automatically saved. • Pressing the PROGRAM key in the Program Setup, the following choice is offered to store the values set: STORE? QUIT The new settings are not activated and the old settings remain valid. STORE? SAVE The new settings are stored permanently in the NVM (Non Volatile Memory).
Power-On Configuration The default values of the various functions are indicated in bold. Entering the Power-On Configuration 1. Make sure that the printer is turned off. 2. Press and hold the PROGRAM key pressed while powering on the printer until the RELEASE KEY message is displayed.
Main Structure P rint out? N O P rint out? Y E S Low. Jam S ens. Y Low. Jam S ens. N U pp. Jam S ens. Y U pp. Jam S ens. N P arall Interface P arallel Interface S ettings S erial Interface S erial Interface S ettin gs Fu nctions Fu nctions B lock B ack to M FG ? N O B ack to M FG ? Y E S The functions concerning the interfaces group the parameters for the configuration of the interfaces.
Printout of the Printer Settings PRINT OUT? NO → or ← PRINT OUT? YES ↓ LOW.JAM SENS.Y PRINT OUT? NO The Setup is not printed. PRINT OUT? YES The printer setup is printed showing the currently selected values. The printout starts as soon as you select this value. Enable/Disable Lower Tractor Jam Sensor PRINT OUT? NO ↑ LOW. JAM SENS. Y → or ← LOW. JAM SENS. N → or ← ↓ UPP. JAM SENS. Y LOW. JAM SENS. Y Enables the paper jam sensor located in the Lower Push Tractor. LOW. JAM SENS.
Enable/Disable Upper Tractor Jam Sensor (only 9078D model) LOW. JAM SENS. Y ↑ UPP. JAM SENS. Y → or ← UPP. JAM SENS. N → or ← ↓ PARALL INTERFACE UPP. JAM SENS. Y Enables the paper jam sensor located in the Upper Push Tractor. UPP. JAM SENS. N Disables the paper jam sensor located in the Upper Push Tractor. When the cutter option is used, the jam sensor should be enabled for higher cut precision.
Parallel Interface This menu defines the use of the parallel interface and is structured according to the interface specific parameters. Parallel Interface Parameters P arall.Interface 1284 B idir. I/F C X Parallel I/F S elect-In H ost S elect-In O n D ata Bits 8 D ata Bits 7 D edic. Buffer 2K D edic. Buffer ... E m ul EP SON E m ul. IBM ... C har. S et ... C har. S et ... N ation ... N ation ... A uto L F ... A uto C R ... A uto L F ... S erial Interface 20 C P I IBM ...
Setting the Interface Parameters Interface Type UPP. JAM SENSOR Y PARALL INTERFACE ↓ ↑ PARALL INTERFACE → 1284 BIDIR I/F → or ← CX PARALLEL I/F → or ← ↓ ↓ SERIAL INTERFACE SELECT-IN HOST 1284 BIDIR i/F Bidirectional IEEE 1284 parallel interface. CX PARALLEL I/F Centronics type parallel interface (monodirectional) Setting the Select-In Signal 1284 BIDIR.
Number of Data Bits SELECT-IN HOST ↑ DATA BITS 8 → or ← DATA BITS 7 → or ← ↓ DEDIC.BUFFER 2K Selection of the number of data bits: 7 or 8 Input Buffer Size DATA BITS 8 ↑ DEDIC.BUFFER 256 → or ← DEDIC.BUFFER 2K → or ← DEDIC.BUFFER 12K → or ← DEDIC.BUFFER 32K → or ← DEDIC.BUFFER 64K → or ← ↓ EMUL. EPSON LQ Selects the input buffer size. If the input buffer is set to 64K, the DLL is not available.
Printer Emulation DEDIC.BUFFER 2K ↑ EMUL. EPSON LQ → or ← EMUL. IBM XL24 → or ← EMUL. IBM XL24AGM → or ← EMUL. IBM 2391 → or ← ↓ CHAR. SET CS2 EMUL. EPSON LQ The printer uses the EPSON LQ 1050/2550 emulation. EMUL. IBM XL24 The printer uses the IBM Proprinter XL24e emulation. EMUL. IBM XL24AGM The printer uses the IBM Proprinter XL24 AGM emulation. EMUL. IBM 2391 The printer uses the IBM Personal 2391+ emulation. EPSON Character Sets EMUL. EPSON LQ ↑ CHAR. SET CS1 → or ← CHAR.
IBM Character sets EMUL. IBM xxx ↑ CHAR. SET CS1 → or ← CHAR. SET CS2 → or ← ↓ NATION CP437 These items select the character set to be used in IBM Proprinter emulation. EPSON National Character sets CHAR. SET CS2 ↑ NATION CP437 → or ← NATION ...
IBM National Character Sets CHAR. SET CS2 ↑ NATION CP437 → or ← NATION ...
CR Code Behavior These items are displayed only if the IBM emulation is selected. NATION xxx ↑ → or ← → or ← AUTO CR NO AUTO CR YES ↓ AUTO LF NO AUTO CR NO No automatic carriage return is performed after a LF, VT or ESCJ code. AUTO CR YES The printer performs an automatic carriage return after a LF, VT or ESCJ code . LF Code Behavior AUTO CR NO or NATION CP437 ↑ AUTO LF NO AUTO LF YES AUTO LF HOST → or ← → or ← → or ← ↓ 20 CPI IBM NO or PARALL INTERFACE AUTO LF NO No Automatic LF after CR.
IBM Compressed Printing These items are displayed only, if the IBM emulation is selected. AUTO LF NO ↑ 20 CPI IBM NO → or ← 20 CPI IBM YES → or ← ↓ PARALL INTERFACE 20 CPI IBM NO The compressed printing is performed at 17,1 cpi. 20 CPI IBM YES The compressed printing is performed at 20 cpi.
Serial Interface This menu defines the use of the serial interface and is structured according to the interface specific parameters. Serial Interface Parameters S erial Inte rface S erial I/F N o S erial I/F ... B aud 9600 B aud ... D ata Bits 8 D ata Bits 7 P arity N on e P arity ... H and sh ake D T R H and sh ake X on /X of C onn ectio n L ocal C onn ect. R em o te D edic. B uffer 2K D edic. B uffer ... E m ul. E P S O N E m ul. IB M ... C har. S et ... C har. S et... N ation ...
Setting the Interface Parameters Interface Type PARALL INTERFACE SERIAL INTERFACE ↑ ↑ SERIAL INTERFACE → SERIAL I/F NO → or ← SERIAL I/F 232 → or ← SERIAL I/F 422 → or ← ↓ ↓ FUNCTIONS BAUD 9600 SERIAL I/F NO The serial interface is disabled SERIAL I/F 232 Defines the usage of the serial interface RS-232/C SERIAL I/F 422 Defines the usage of the serial interface RS-422/A 46
Baud Rate SERIAL I/F NO ↑ BAUD 300 → or ← BAUD 600 → or ← BAUD 1200 → or ← BAUD 2400 → or ← BAUD 4800 → or ← BAUD 9600 → or ← BAUD 19200 → or ← BAUD 38400 → or ← ↓ DATA BITS 8 The baud rate is selected in bits per second. The above values can be selected. Number of Data Bits BAUD 9600 ↑ DATA BITS 8 → or ← DATA BITS 7 → or ← ↓ PARITY NONE Selection of the number of data bits: 7 or 8.
Parity Check DATA BITS 8 ↑ PARITY NONE → or ← PARITY ODD → or ← PARITY EVEN → or ← PARITY MARK → or ← PARITY SPACE → or ← ↓ HANDSHAKE DTR PARITY NONE Data does not have a parity bit, i.e. 8 bit data are transferred and the parity check is disabled. PARITY ODD Parity check is enabled for odd parity. PARITY EVEN Parity check is enabled for even parity. PARITY MARK Parity check is disabled and the transmitted parity bit is always a Mark.
Handshake Protocol PARITY NONE ↑ HANDSHAKE DTR → or ← HANDSHAKE XONXOF → or ← ↓ CONNECTION LOCAL HANDSHAKE DTR The Handshake is performed using the DTR Protocol. HANDSHAKE XONXOF The Handshake is performed using the XON-XOFF Protocol. Connection Type HANDSHAKE DTR ↑ CONNECTION LOCAL → or ← CONNECT. REMOTE → or ← ↓ DEDIC.BUFFER 2K Selects the connection type: local or remote.
Input Buffer Size DATA BITS 8 ↑ DEDIC.BUFFER 256 → or ← DEDIC.BUFFER 2K → or ← DEDIC.BUFFER 12K → or ← DEDIC.BUFFER 32K → or ← DEDIC.BUFFER 64K → or ← ↓ EMUL. EPSON LQ Selects the input buffer size. If the input buffer is set to 64K, the DLL is not available. Printer Emulation DEDIC.BUFFER 2K ↑ EMUL. EPSON LQ → or ← EMUL. IBM XL24 → or ← EMUL. IBM XL24AGM → or ← EMUL. IBM 2391 → or ← ↓ CHAR. SET CS2 EMUL. EPSON LQ The printer uses the EPSON LQ 1050/2550 emulation. EMUL.
EPSON Character Sets EMUL. EPSON LQ ↑ CHAR. SET CS1 → or ← CHAR. SET CS2 → or ← CHAR. SET ITALIC → or ← ↓ NATION CP437 These items select the character set to be used in EPSON emulation. IBM Character sets EMUL. IBM xxx ↑ CHAR. SET CS1 → or ← CHAR. SET CS2 → or ← ↓ NATION CP437 These items select the character set to be used in IBM Proprinter emulation.
EPSON National Character sets CHAR. SET CS2 ↑ NATION CP437 → or ← NATION ...
IBM National Character Sets CHAR. SET CS2 ↑ NATION CP437 → or ← NATION ...
CR Code Behavior These items are displayed only if the IBM emulation is selected. NATION xxx ↑ AUTO CR NO → or ← AUTO CR YES → or ← ↓ AUTO LF NO AUTO CR NO No automatic carriage return is performed after a LF, VT or ESCJ code. AUTO CR YES The printer performs an automatic carriage return after a LF, VT or ESCJ code . LF Code Behavior AUTO CR NO or NATION CP437 ↑ AUTO LF NO → or ← AUTO LF YES → or ← ↓ 20 CPI IBM NO or SERIAL INTERFACE AUTO LF NO No Automatic LF after CR.
IBM Compressed Printing These items are displayed only, if the IBM emulation is selected. AUTO LF NO ↑ 20 CPI IBM NO → or ← 20 CPI IBM YES → or ← ↓ SERIAL INTERFACE 20 CPI IBM NO The compressed printing is performed at 17,1 cpi. 20 CPI IBM YES The compressed printing is performed at 20 cpi.
Functions This item groups various printer functions, with which you can configure the printer. 9078 plus model Paper Overly? No Sequence None Sequence ... Buzzer Yes Buzzer No Quick No Quick Yes Back to Mfg? No Paper Overly? Yes Ribbon Black Ribbon Color Bar C odes 60 Bar C odes 90 Text Direct Bi Text Direct U ni Graph D irect Bi Graph D irect Uni Bar C ode Bi Bar C ode Uni P.On Path M acro P.
9078D plus model S equence N o ne S equence ... B uzzer Yes B uzzer N o R ib bon Black R ib bon C olor B ar C odes 60 B ar C odes 90 Text D irect Bi Text D irect U ni G rap h D irect B i G rap h D irect U ni B ar C ode Bi B ar C ode U ni P.O n Path M acro P.
Setting the Functions Group Items SERIAL INTERFACE FUNCTIONS ↑ ↑ FUNCTIONS → ↓ PAPER OVERLY NO 9078 plus SEQUENCE NONE 9078D plus ↓ BACK TO MFG: NO SEQUENCE NONE or BUZZER YES 9078 plus 9078D plus Paper Overlapping (9078 plus model only) FUNCTIONS ↑ PAPER OVERLY NO → or ← PAPER OVERLY YES → or ← ↓ SEQUENCE NONE PAPER OVERLY NO When feeding a cut sheet through the manual entry slot, the fanfold paper must be parked.
Paper Loading Sequence FUNCTIONS (9078D plus model) or PAPER OVERLY NO (9078 plus model) ↑ SEQUENCE NONE → or ← SEQ. L + U PUSH (9078D plus model only) → or ← SEQUENCE ASF1+2 → or ← SEQUENCE ASF123 → or ← ↓ BUZZER YES These items are displayed only, if the accessories to which they refer are installed. SEQUENCE NONE The paper is fed only through the path selected by operator panel. SEQ.
Enable/Disable the Buzzer SEQUENCE NONE ↑ BUZZER YES → or ← BUZZER NO → or ← ↓ QUICK YES (9078 plus model) or BLACK RIBBON (9078D plus model) Enable or disables the buzzer. Quick Manual Loading through the Manual Slot (9078 plus model only) BUZZER YES ↑ QUICK NO → or ← QUICK YES → or ← ↓ RIBBON BLACK QUICK NO The single sheet in the manual path is loaded by the operator. The printer is then disabled. QUICK YES The single sheet in the manual path is loaded automatically.
Ribbon Type Selection QUICK YES (9078 plus model) or BUZZER YES (9078D plus model) ↑ RIBBON BLACK → or ← RIBBON COLOR → or ← ↓ BAR CODE 60DPI Selects the ribbon type to be used with the printer: black or color. Bar Code Density RIBBON BLACK ↑ BAR CODE 60DPI → or ← BAR CODE 90DPI → or ← ↓ TEXT DIRECT BI Selects the bar code print density: 60 or 90 dpi.
Graphics Print Direction TEXT DIRECT BI ↑ GRAPH DIRECT BI → or ← GRAPH DIRECT UNI → or ← ↓ BARCODES DIR.UNI Selects the print direction for graphics: bidirectional or unidirectional. Bar Codes Print Direction GRAPH DIRECT BI ↑ BARCODES DIR.BI → or ← BARCODES DIR.UNI → or ← ↓ P. ON PATH MACRO Selects the print direction for bar codes: bidirectional or unidirectional.
Paper Path at Power-On BARCODES DIR.UNI ↑ P. ON PATH MACRO → or ← P. ON PATH LAST → or ← ↓ MENU ENGLISH P. ON PATH MACRO The paper path at power-on is the one from the default Macro. P. ON PATH LAST The paper path at power-on is the last one that was selected before the printer was powered off. Selection of the Language of the Display Messages P.
Resetting to Factory Default Values With the BACK TO MFG function it is possible to reset all items in the Power On Configuration and in the Program Setup to their factory default values. This may be useful if you do not remember the values you set in the menus, or because you simply changed you mind about the settings you have just done.