User's Manual

ManualsBrandsCompex Systems ManualsComputers & AccessoriesWIRELESS-ABGN 2X2 NETWORK MINIPCIE ADAPTER

wireless modules

Last Updated: 21/06/16

KEY FEATURES

• Qualcomm Atheros AR9280

• Atheros XB92 Reference Design

• Dual-band 2x2 MIMO spatial multiplexing technique

• 2.4GHz max 18dBm & 5GHz max 17dBm output power

(per chain)

• IEEE 802.11n compliant & backward compatible with

802.11b/g

• 2x2 MIMO Technology, up to 300Mbps

• Mini PCI Express 1.1 interface

• Supports WPA2 encryption (IEEE 802.11i) and 802.1X

authentication

• Supports Transmit Power Control (IEEE 802.11h)

• Dynamic Frequency Selection (DFS)

• Supports additional regulatory domains (IEEE802.11d)

Dual Band 2x2 MIMO 802.11n Mini PCIe Module

Designed for Dual Band Wireless Access Points

Specications

Chipset AR9280

Host Interface Mini PCI-Express 1.1 Standard

Operating Voltage 3.3V DC

Antenna Connector 2x U.FL

Frequency Range 2.4GHz: 2.412 ~ 2.484 GHz

5GHz: 5.150 ~ 5.875 GHz

Certiﬁcation FCC & CE Certiﬁed, RoHS Compliant

Power Consumption 3.7W (Max)

Modulation Techniques OFDM: BPSK, QPSK, 16-QAM, 64-QAM

Temperature Range

(for WLE200NX)

Operating: -20ºC to 70ºC

Storage: -40ºC to 90ºC

Industrial Grade Temperature Range

(for WLE200NX-I)

Operating: -40ºC to 70ºC

Storage: -40ºC to 90ºC

Humidity Operating: 5% to 95% (non-condensing)

Storage: Max. 90% (non-condensing)

Dimensions (H x W x D) 50.95 x 30 x 3.2 mm

Model: WLE200NX / WLE200NX-I

Summary of content (6 pages)

PAGE 1
wireless modules Dual Band 2x2 MIMO 802.11n Mini PCIe Module Designed for Dual Band Wireless Access Points Model: WLE200NX / WLE200NX-I KEY FEATURES • • • • • • • • • • • Qualcomm Atheros AR9280 Atheros XB92 Reference Design Dual-band 2x2 MIMO spatial multiplexing technique 2.4GHz max 18dBm & 5GHz max 17dBm output power (per chain) IEEE 802.11n compliant & backward compatible with 802.11b/g 2x2 MIMO Technology, up to 300Mbps Mini PCI Express 1.1 interface Supports WPA2 encryption (IEEE 802.11i) and 802.
PAGE 2
wireless modules RF Performance Table 2.4GHz 802.11b 2.4GHz 802.11g 2.4GHz 802.11n HT20 2.4GHz 802.11n HT40 5GHz 802.11a 5GHz 802.11n HT20 5GHz 802.11n HT40 2 Data Rate TX Power (per chain) TX Power (2 chains) Tolerance Data Rate RX Specifications Sensitivity Tolerance 1Mbps 18dBm 21dBm ±2dB 2Mbps 18dBm 21dBm ±2dB 1Mbps -94dBm ±2dB 2Mbps -94dBm 5.5Mbps 18dBm 21dBm ±2dB ±2dB 5.
PAGE 3
wireless modules Connector Map Mini PCIe 1.1 Connector U.FL connectors CH0, CH1 Mechanical Dimensions 3 Copyright © Compex Systems. All rights reserved. COMPEX and the COMPEX logo, are registered trademarks of Compex Inc. Atheros and other trademarks are properties of their respective owners. While every effort is made to ensure the information is accurate, Compex does not accept liability for any errors or mistakes that may arise. All specifications are subject to change without notice.
PAGE 4
wireless modules Packaging Content Item Quantity WLE200NX Wireless Module 1 Ordering Configuration Item Code Model PA Form factor Card Information WLE200NX 7A0000 WLE200NX SE5516A Full size card 802.11 a/b/g/n Mini PCIe card WLE200NX-I SE5516A Full size card 802.11 a/b/g/n Mini PCIe card WLE200NX 7A0000 Packaging Information 4 Packaging Type Dimensions Weight Dimensional Weight Carton Box (250 units) 422 x 410 x 240 mm 4.65 kg 8.46 kg Copyright © Compex Systems.
PAGE 5
COMPLIANCE INFORMATION FCC NOTICE This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 6
OEM integration instructions: This device is intended only for OEM integrators under the following conditions： The module is only limited to installation in mobile applications. The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmit or antenna. The module shall be only used with the integral antenna(s) that has been originally tested and certified with this module.