5G M.
Copyright Copyright © 2019 COMPAL ELECTRONICS, INC. All rights reserved. Without the prior written permission of the copyright holder, any company or individual is prohibited to excerpt, copy any part of or the entire document, or distribute the document in any form. Notice The document is subject to update from time to time owing to the product version upgrade or other reasons. Unless otherwise specified, the document only serves as the user guide.
Content 1. 2. 3. Foreword ....................................................................................................................................................................................... 4 1.1 Introduction ............................................................................................................................................................................. 4 1.2 Safety Information ..............................................................................
1. Foreword 1.1 Introduction This document describes the hardware of the COMPAL® 5G RXM-G1 M.2 Module products. It helps you quickly retrieve interface specifications, electrical and mechanical details, and information on the requirements to be considered for integrating further components. 1.2 Safety Information The following safety precautions must be observed during all phases of operation, such as usage, service or repair of any cellular terminal or mobile incorporating with 5G RXM-G1 M.2 module.
Cellular terminals or mobiles operating over radio signals and cellular network cannot be guaranteed to connect in all possible conditions (for example, with unpaid bills or with an invalid (U) SIM card). When emergent help is needed in such conditions, please remember using emergency call. In order to make or receive a call, the cellular terminal or mobile must be switched on in a service area with adequate cellular signal strength. The cellular terminal or mobile contains a transmitter and receiver.
2. Overview 2.1 Introduction 5G RXM-G1 M.2 MODULE is a highly integrated 5G NR wireless communication module that adopts standard PCIe RXM-G1M.2 interface and backward supports with LTE/WCDMA system. It is applicable to most broadband communication networks of the mobile operator across the world. RXM-G1 has capability on 5G NR Sub6 and mmWave on HW design and using SW to inactive on 5G NR mmWave function. 2.2 Specification Table 2-1 RXM-G1 5G M.
Uplink 5G sub-6 1CC; Max BW 100MHz; 5G mmWave 8CC; Max BW 800MHz;MIMO 2x2 HPUE ( Class 2) B41 DL 4x4 MIMO B2, B4, B7, B25, B30, B41, B48, B66 n2, n41, n66 Carrier aggregation ULCA, DLCA and EN-DC SRS antenna switching n41 : 1T2R(NSA) Power Supply DC 3.135V～3.465V, Typical 3.3V Temperature Operating temperature[1]:-10°C ～+55°C Extended temperature[2] : -25°C ～+75°C Storage temperature: -40°C ～+85°C Interface: PCIe M.2 Key B Physical Dimension: 30x52 mm, Thickness=2.25 mm(typ.
Protocol Stack IPV4/IPV6 AT commands 3GPP TS 27.007 and 27.
2.3 Operating Band The 5G RXM-G1 M.
Table 4-7 LTE FDD Mode Band Typical Value (dBm) Band 2 Band 4 Band 5 Band 7 Note 23 ±2 23 ±2 23 ±2 23 ±2 23 Band 12 Band 13 LTE FDD Band 14 ±2 23 ±2 23 ±2 23 Band 25 ±2 23 Band 26 ±2 23 Band 30 ±2 23 Band 66 ±2 23 Band 71 ±2 Table 4-8 LTE TDD Mode Band Band 41 LTE TDD Band 48 Typical Value (dBm) Note 26 ±2 23 ±2 Table 4-9 NR-FR1 FDD Mode Band n2 Typical Value (dBm) Note 23 ±2 NR-FR1 n5 23 ±2 FDD n66 23 ±2 n71 23 ±2 Table 4-10 NR-FR1 TDD Page 10
Mode Band NR-FR1 TDD Typical Value (dBm) Note 23 (LTE+NR) n41 ±2 2.5 Antennas (Maximum allowable gain) Vendor Pulse Modulation Frequency (MHz) Max. Allowable Antenna Gain (dBi) WCDMA / HSPA Band II 1852.4 ~ 1907.6 10.07 WCDMA / HSPA Band IV 1712.4 ~ 1752.6 6.20 WCDMA / HSPA Band V 826.4 ~ 846.6 9.42 LTE Band 2 / NR n2 1850 ~ 1910 7.50 LTE Band 4 1710 ~ 1755 6.14 LTE Band 5 / NR n5 824 ~ 849 7.00 LTE Band 7 2500 ~ 2570 8.00 LTE Band 12 699 ~ 716 6.
3. Legal Information FCC Statement: Any device incorporating this module must include an external, visible, permanent marking or label which states: “Contains FCC ID: GKRRXMG1” The RXM-G1 modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Canadian Notice This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
