File Number: 980094-F June |, 1998 FCC ID: GKRM57) APPENDIX 5 USER’S MANUAL OF EUT The enclosed manual is for the EUT. As you will notice on the preceding page of this manual is the FCC WARNING about radio and television interference as per the requirement set forth in Part 15 of the FCC Rules. Accredited Lab. of ANEMONE, ALA Page 20 of 28 Listed Lab. of FCC, VCC, MOC ALA Certificate #: 824.01 (for Emission) ANEMONE Authorization #: ELA 124 (for EMC) Rev.
Important Safety Instructions Ease read these instructions thoroughly. Please keep this guide for feature use. Please discomfit the device from the main supply before cleaning. Do not use any liquid or aerosol spray cleaners. The bust for cleaning is a puce of cloth dampened with water. To avoid damage of the device, you should only use accessory parts permitted by the manufacturer. The device must be protected against moisture. To setup the device, it must be put in a stable stand position.
FEDERAL COMMUNICATIONS COMMISSION (FCC STATEMENT) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents — Chapter 1 Introduction Unpacking N a Connecting the Monitor and Stand _ Choosing a Workstation The AC Connection The Signal Cable Connection Monitor Adjustments Chapter 2, 22 Icon Descriptions Lula Technical Information Monitor Specifications _ Preset Timing — 9 Preset mode timing 9 Troubleshooting — 10 Caring For Your Monitor _ 11 Cleaning the screen_ HL Ventilation slots ee 1 Power Cord 11 Grounding
2 + CHAPTER 1 Introduction Congratulations on your purchase of the new high performance 15” Monitor. Much consideration has gone into the design of the monitor in order to meet your requirements for full compatibility and versatility as well as quality Using state-of-the-art electronics, the monitor can support a resolution of 1280x1024, User display settings will be automatically saved to memory.
Connecting tie Monitor and Stud ® Alien the stand’s four tabs with the slots on the bottom of the monitor. * Insert the tabs into the slots. « Slide the stand towards the front of the monitor. Figure 1: Monitor and Stand Connection Choosing A Workstation ‘When choosing an appropriate workspace, keep these few things in mind: + As tardy, level surface.
The AC Connection The AC Connection + Locate the AC port on the rear of the monitor + Plug the female end of the AC cord into the AC port « Plug the male end into the power supply.
The Signal Cable Connection The Signal Cable Connection + Locate the ON/OFF power switch. See Figure 4, + Make sure that the Monitor power switch is in the OFF position. The OFF position is indicated with a circular icon. Figure 4: ON/OFF Power Switch + Locate the VGA port on the rear of the PC. The signal cable has a standard 15-pin mini D-sub (VGA) connector. If you are having trouble locating the VGA port, please refer to the documentation which came with your PC.
Monitor Adjustments ££ Monitor Adjustments The monitor is capable of both tilt and swivel adjustments, 5 Figure 5: Tilt Adjustment + With the tilt feature, the monitor is capable of vertical adjustments of +159 10 25° + The swivel feature allows for horizontal monitor adjustments of +435° to -45°,
User Controls Chapter 2 This display device shall have external controls to implement at least the following function: + POWER SWITCH . + POWER INDICATOR + + BRIGHTNESS CONTROL + + CONTRAST CONTROL . + HORIZONTAL WIDTH CONTROL + + VERTICAL HEIGHT CONTROL . + PINCUSHION CONTROL + TRAPEZOID CONTROL + TILT control TILT control R gain control G gain control B gain control HORIZONTAL phase control Vertical center control A recall function shall be present on the monitor to recall the factory preset.
Icon Descriptions MOO icon Descriptions LET Contrast: This control allows you to adjust the display contrast level to accommodate the ambient lighting conj. sons of your working environment, Brightness: This control allows you to fine tune the display brightness level. H-Width: This control allows you to stretch or squeeze the display area horizontally. H-Phase: This control allows you to adjust the display to the right or to the left.
Technical Information ® Technical Information Monitor Specifications 15" CRT Dot Pitch (mm) 0.28 Surface No Viewable Display Area fim) 260 x 195 Input Signal Video Suns. RGB Analog Ohm a Separate HAV, TTL (+7) b. Composite H-V, TTL Scanning Frequency Horizontal (KHz) Vertical (Hz) Idea Bandwidth 110MHz Max, Resolution 1280 % 1024 Compatibility IBMVGA, VESALIUS.
Preset Timing Preset Timing JA] 8] CKD soc LT LT k Preset mode timing FOO We [mem [Eds Vine | powers | rein | wow | tai TEx I TER aunt TER TH ami Figure 9 Note: > Primary mode is the key timing which is adjusted and compliant ta the product specification during the production at the factory. All other preset timings are secondary and adjusted roughly within the change of product nature. It may require a fine tune to gain optimal settings. for user’s application.
Caring For Your Monitor C0) Caring For Your Monitor Cleaning the screen To clean your screen follow these steps: » Never spray liquid cleaners on or around the Monitor. + Spray the liquid cleaner on a rag while standing away farm the computer. Avoid excessive dampening, * Clean the screen with slightly damp rag Ventilation slots The ventilation slots allow air to flow through the Monitor. They protect the unit from overheating. Therefore, do not cover or obstruct the ventilation slots.