re — o Important Safety Instructions Please read these instructions thoroughly. Please keep this guide for future use. Please disconnect the device from the main supply before cleaning. Do not ise any liquid or aerosol spray cleaners. The best for cleaning is a piece of cloth dampened with water. To avid damage of the device, you should only use accessory parts permitted by the manufacturer. The device must be protected against moisture. To setup the device, it must be put in a stable stand position.
Federal Communications Commission (FCC Statement) This equipment has been tested and found to comply with the limits fora Class B digital device. pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause armful interference to radio communications.
L GETTING STARTED. Unpacking C connecting Choosing the Monitor ang Stand. A Workstation, The 4C Connection... The Signal Cable Connection 2. MONITOR ADJUSTMENT User Control's. [ER The Monitor's F, unction; 3. ICON DESCRIPTIONS 4. TECHNICAL INFORMATION 15" Monitor Specifications Pres er 7 Ming. 3: TROUBLE SHOOTING Power 6. CARING FOR YOUR Cleaning the screen Ventilation offside Power Cord Grounding...
1. Getting Started Introduction This document is related to a 14" CRT color monitor TM 134 10 be used with various kind of graphic adapters, including IBMVGA, VESALIUS OVERGRAZE SAGA, VGA, and XGA modes. It is intended as a mutineer monitor type based on microprocessor unit, capable to support all the video standards. Other graphic standards can be supported by this monitor, simply adjusting image size and centering by means of the user controls gathered on the front panel.
Getting Started The 14” Monitor Connecting the Monitor and Stand * Align the stand’s four tabs with the slots on the bottom of the monitor. * Insert the tabs into the slots. ¢ Slide the stand towards the front of the monitor. Figure I: Monitor and Stand Connection Choosing A Workstation When choosing an appropriate workspace, keep these few things in mind: + Sturdy, level surface + An electrical wall outlet and a telephone wall jack near the computer.
The 14” Monitor Getting Started Figure 2: The Workstation The AC Connection + Locate the AC port on the rear of the monitor + Plug the female end of the AC cord into the AC port.
Monitor Adjustments The 14” Monitor The Signal Cable Connection + Locate the IF power switch. Ses Figure 4. + Make sure that the Monitor power switch is in the OFF position. The OFF position is indicated with a circular icon. Paar LED = Power On OF Button = Figure 4: ON/OFF Power Switch + Locate the VGA port on the rear of the PC. The signal cable has a standard 15-pin mini D-sub (VGA) connector. If you are having trouble locating the VGA port.
2 Monitor Adjustments ~ The monitor is capable of both tilt and swivel adjustments.
Monitor Adjustments The 147 Monitor User Controls This display device shall have external controls 1 implement at least the following function: POWER SWITCH POWER INDICATOR BRIGHTNESS CONTROL CONTRAST CONTROL HORIZONTAL WIDTH CONTROL VERTICAL HEIGHT CONTROL PINCUSHION CONTROL TRAPEZOID CONTROL recall function shall be present on the monitor to recall the factory preset.
3 Icon Descriptions Icon scrips « Contrast: This control allows you to adjust the display contrast level to accommodate the ambient lighting conditions of your working environment, Brightness: This control allows vou to fine tune the display brightness level H-Width: This control] allows you to stretch or squeeze the display area horizontally H-Phase: This control allows vou to adjust the display to the right or to the left V-Height: This control allows you to stretch or squeeze the display arcs vertically.
4 Technical Information 14” Monitor Specifications Screen 13° CRT Cot Pitch (nm) 0.28 Success Non-glare Display Size 250% 188 Input Signal Video Suns RGB Analog 750k Separate HAV. TTL (+1) Scanning Frequency Horizontal (KHz) Si Vertical (Hz) 30-120 Video Bandwidth MHz Max. Resolution 1024x768 Compatibility VGA, SAGA, 8514A. VASE Plug & Play onc! & DDC2B Display Colors. Minimized Sigma! Cable Captive 15 pia.
The 15” Monitor Display Modes Presetting User Technical Information Low Radiation MPR 1! Optional Operating Temperature Relative Humidity 040°C Dimensions © 388mmL) x 366mmiW) x 37Tmm(H} thudding tilt and swivel base) Weight excluding packaging) 120kg Preset Timing Foe me sweep < B A MOE Flint TERR] Thais) | © Tos) Oles) T Th) Lines [ Poland | piing Tums)! Tums) | Tome) Sous) 1 Thus) & dot Lepta | backpacker | pale | Ghent 1] vase | es Shane | mom 1907 381 1 0635 130 91 | 10.683 1042 0063 | oar : 00 ws 46.
5 Trouble Shooting ~ This section will try to anticipate potential problems that You may encounter in the day-to-day use of your monitor. Included in this section is information which should help solve these problems for you. If after trying the suggested solutions, your monitor’s symptom remains the same, contact your authorized service center, Power switched on. but the power LED is Symptom: The monitor net li. Solution: Check to make sure that the power cord and video cable are properly concreted.
6 Caring For Your Monitor Cleaning the screen To clean your screen follow these steps: * Never spray liquid cleaners on or around the Monitor. * Spray the liquid cleaner an a rag while standing away from the computer. Avoid excessive dampening. » Clean the screen with slightly damp rag Ventilation slots The ventilation slots allow air to flow through the Monitor. They protect the unit from overheating, Therefore, do not cover or obstruct the ventilation slots.
File Numerable: 980045-F April 21. 1998 FCC ID: GKRM434 APPENDIX 5 USER’S MANUAL OF EUT The enclosed manual is for the EUT. As you will notice on the preceding page of this manual is the FCC WARNING about radio and television interference as per the requirement set forth in Part 15 of the FCC Rules. Accredited Lab. of ANEMONE, ALA Page 19 of 27 Listed Lab. of FCC, VCC, MOC ALA Certificate #: 824.01 (for Emission) ANEMONE Authorization #: ELA 124 (for EMC) Rev.