Installation Manual

ManualsBrandsComnet ManualsElectronicsMiniature 1-Ch Ethernet-over-COAX PoE Powered

INS_CLRFE1EOCX/M-REV- 12/23/14 PAGE 1TECH SUPPORT: 1.888.678.9427

INSTALLATION AND OPERATION MANUAL

CLRFE1EOC(E,P)/M Series

MINI ETHERNET-OVER-COPPER EXTENDER REMOTE UNITS

The ComNet™ CopperLine® Ethernet-over-coax minis are an ultra-small form factor

addition to the ComNet Copperline product family. These miniature remote units

provide 10/100 Mbps Ethernet data with or without Pass-through PoE power over

extended distance coaxial cable. Available in both standard and PoE applications,

the mini CopperLine units are automatically configured as remote units.

Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining equipment

operating status. Table 3 on Page 4 describes the LED indicators for each light on

the unit.

The mini CopperLine units are stand-alone with a small footprint for use where

space is extremely limited. They may optionally be DIN-rail mounted by the

addition of ComNet model DINBKT4 adaptor. See Figure A on Page 5 for mounting

instructions.

This manual serves the following

ComNet Model Numbers:

CLRFE1EOCE/M

CLRFE1EOCP/M

Summary of content (5 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL CLRFE1EOC(E,P)/M Series MINI ETHERNET-OVER-COPPER EXTENDER REMOTE UNITS POWERED BY EXTERNAL OR POE SOURCE This manual serves the following ComNet Model Numbers: CLRFE1EOCE/M CLRFE1EOCP/M The ComNet™ CopperLine® Ethernet-over-coax minis are an ultra-small form factor addition to the ComNet Copperline product family. These miniature remote units provide 10/100 Mbps Ethernet data with or without Pass-through PoE power over extended distance coaxial cable.
PAGE 2
INSTALLATION AND OPERATION MANUAL CLRFE1EOC(E,P)/M Series FIGURE 1 – CLRFE1EOCE/M SINGLE CHANNEL COAX REMOTE EXTERNALLY POWERED UNIT ETHERNET Black w/ White Stripe (AC or DC–) Black (AC or DC+) EXT DISTANCE FRONT REAR Power: 9 to 36 VDC OR 24 VAC Power Consumption: 1.5 W 10/100 data rate DIP switch See Installation Instructions, Step 1 FIGURE 2 – CLRFE1EOCP/M SINGLE CHANNEL COAX REMOTE PASS-THROUGH-POE POWERED UNIT ETHERNET Power: S upplied via PoE from Head End Power Consumption: 1.
PAGE 3
INSTALLATION AND OPERATION MANUAL CLRFE1EOC(E,P)/M Series APPLICATION DIAGRAMS Ethernet Connection Extended Connection PoE Power PoE Pass-Through Mode PoE Ethernet Switch or Midspan Local Remote CLFE1EOC CLRFE1EOCP/M Local Remote CLFE1EOC CLRFE1EOCE/M IP Camera Power Power PoE Camera Non-PoE Mode Ethernet Switch Power IMPORTANT NOTE. PLEASE READ. The applications are shown as general representations only and are not intended to show detailed network topologies.
PAGE 4
INSTALLATION AND OPERATION MANUAL CLRFE1EOC(E,P)/M Series INSTALLATION INSTRUCTIONS 1 - SET 10/100 SWITCH Locate the 10/100 data rate DIP switch on the local unit. Set the data rate according to bandwidth required. The default setting for the data rate DIP switch is 100Mbps. NOTE: The data rate must be set the same on both the local and remote units. 2 - SET LOCAL/REMOTE SWITCHES (1 AND 4 CHANNEL UNITS ONLY, FOR RACK UNITS SKIP TO STEP 4) Locate the Local/Remote Dip switch and set to “LC” at the head end.
PAGE 5
INSTALLATION AND OPERATION MANUAL INSTALLATION CONSIDERATIONS The CLRFE1EOC(E,P)/M is supplied as a standalone/surface mount (mini size) module. Units should be installed in dry locations protected from extremes of temperature and humidity. CLRFE1EOC(E,P)/M Series FIGURE A Dimensions are for a mini size module WARNING: Unit is to be used with a Listed Class 2 power supply.