Installation Manual

ManualsBrandsComnet ManualsElectronics10/100TX Drop/Insert/Repeat 4TX/2EX Self-Managed

INS_CLFE4+2SMS[POE](C,U)_REV– 10/27/11 PAGE 1TECH SUPPORT: 1.888.678.9427

INSTALLATION AND OPERATION MANUAL

CLFE4+2SMS[POE](C,U) Series

10/100TX DROP/INSERT/REPEAT 4TX/2EX

SELF-MANAGED SWITCH WITH POE+

The ComNet CLFE4+2SMS[POE](C,U) is a six-port Ethernet switch with add/drop/repeat

functionality and provides 4 copper ports operating at 10/100Mbps and is designed to

combine four electrical ports along with the incoming Cat5, UTP or Coax CopperLine®

extension port into a further CopperLine extension port that forwards this data to

the next CopperLine network device. There is no programming required to use this

product. The ComNet CLFE4+2SMS(C,U) comes pre-programmed, preventing network

video flooding with DIP switch selection of the first CopperLine port as an uplink or as

an unmanaged switch. Ports 1–4 of the CLFE4+2SMSPOE(C,U) can supply up to thirty

(30) watts of Power over Ethernet (PoE) and incorporate PoE+ features based on the

IEEE 802.3at standard. It is “Plug-and-Play”.

This manual serves the following

ComNet Model Numbers:

CLFE4+2SMSC

CLFE4+2SMSU

CLFE4+2SMSPOEC

CLFE4+2SMSPOEU

Summary of content (7 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL CLFE4+2SMS[POE](C,U) Series 10/100TX DROP/INSERT/REPEAT 4TX/2EX SELF-MANAGED SWITCH WITH POE+ This manual serves the following ComNet Model Numbers: CLFE4+2SMSC CLFE4+2SMSU CLFE4+2SMSPOEC CLFE4+2SMSPOEU TECH SUPPORT: 1.888.678.
PAGE 2
INSTALLATION AND OPERATION MANUAL CLFE4+2SMS[POE](C,U) Series CLFE4+2SMSU PHYSICAL DESCRIPTION Figure 1 – Physical Features of CLFE4+2SMSU 1 3 5 7 6 2 4 8 Table 1 – Physical Feature Descriptions Call-out Description Manual Reference 1 Power Indicating LED (Unlabeled LED Reserved for Future Use) See Table 3 - Indicating LEDs 2 10/100 TX RJ-45 Ports 1 through 4 and Link/Activity (L/A) Indicating LEDs See Installation Instructions, Step 5 See Table 3 - Indicating LEDs 3 Channel 1 Extended Dis
PAGE 3
INSTALLATION AND OPERATION MANUAL CLFE4+2SMS[POE](C,U) Series CLFE4+2SMSPOEU PHYSICAL DESCRIPTION Figure 1 – Physical Features of CLFE4+2SMSPOEU 1 3 5 6 2 4 7 8 Table 1 – Physical Feature Descriptions Call-out Description Manual Reference 1 Power Indicating LED (Unlabeled LED Reserved for Future Use) See Table 3 - Indicating LEDs 2 10/100 TX RJ-45 Ports 1 through 4 and Link/Activity (L/A) Indicating LEDs See Installation Instructions, Step 5 See Table 3 - Indicating LEDs 3 Channel 1 Extend
PAGE 4
INSTALLATION AND OPERATION MANUAL CLFE4+2SMS[POE](C,U) Series Installation Instructions 1 - SET DATA RATE DIP SWITCHES Locate the 10/100 data rate DIP switch on the unit. Set the data rate according to bandwidth required. NOTE: The data rate must be set the same on both the local and remote units. 2 - SET WIRE PAIR DIP SWITCHES (UTP MODELS ONLY, FOR COAX MODELS SKIP TO STEP 3) Locate the wire pair DIP switch on the unit. Set the pair according to number of twisted wire pairs used (1 or 4).
PAGE 5
INSTALLATION AND OPERATION MANUAL CLFE4+2SMS[POE](C,U) Series Table 4 – Approximate Maximum Extended Distances¹ Media Extended Port Data Rate Extended Distance1 1 COAX - RG59/U UTP - 1 pair UTP - 4 pair 10M 100M 10M 100M 10M 100M 5,000 ft 2,000 ft 3,000 ft 1,000 ft 3,000 ft 2,000 ft 1,524 m 610 m 914 m 305 m 914 m 610 m istance figures are obtained using in-house testing mirroring installations.
PAGE 6
INSTALLATION AND OPERATION MANUAL CLFE4+2SMS[POE](C,U) Series Application notes 1 Mixed PoE and Non-PoE systems can be implemented. 2 Lower data rates generally provide longer operating distances.
PAGE 7
INSTALLATION AND OPERATION MANUAL INSTALLATION CONSIDERATIONS These units are supplied as Standalone/Rack mounted module. Units should be installed in dry locations protected from extremes of temperature and humidity. CLFE4+2SMS[POE](C,U) Series FIGURE A Dimensions are for a ComFit module WARNING: Unit is to be used with a Listed Class 2 power supply.