User's Manual

ManualsBrandsCommunication Components ManualsElectronicsPCS Band Multi Carrier Cell Extender

Table Of Contents

Communication Components, Inc.

89 Leuning Street Phone: 201-342-3338

South Hackensack, NJ 07606 Fax: 201-342-3339

PCS Band Multi Carrier Cell Extender

CCI Model Number CE-1819-125MC-XXXX

USER’S GUIDE

Product Description:

Communication Components, Inc. PCS CDMA Multi-carrier Cell Extender

improves the performance of CDMA Base Stations (BTS) in indoor and outdoor

locations, allowing for cost efficient implementation of high capacity radio

networks.

By increasing both the downlink power and receive sensitivity, CCI’s Cell

Extender increases the overall coverage area and improves the performance of

the site.

Operation Description:

CCI’s Multi-channel CDMA Cell Extender is designed to improve overall site

performance by boosting both forward and reverse link parameters in a balanced

manner. The system is designed to provide 125 Watts of usable CDMA output

power per sector antenna (63 W per sector antenna for Canada) and can serve

up to three sectors with two feeder antennas per sector. As such, a CE-1819-

125MC system used in six-carrier sector with 3 carriers per antenna can delivers

40 W per carrier (21 W per carrier for Canada).

• CCI supplies Cell Extender cabinet that requires a dual 30A 208/240V breaker

and two batteries for backup purposes.

RF Connection

Cell Extender cabinet must be bolted to the frame.

• Connect Cell Extender input Tx/Rx and Rx ports (connectors type N located on

the connectors plate inside of the main cabinet) with DO and D1 ports of BTS in

the proper sector using two DIN-N jumpers.

Summary of content (4 pages)

PAGE 1
Communication Components, Inc. 89 Leuning Street South Hackensack, NJ 07606 Phone: 201-342-3338 Fax: 201-342-3339 PCS Band Multi Carrier Cell Extender CCI Model Number CE-1819-125MC-XXXX USER’S GUIDE Product Description: Communication Components, Inc. PCS CDMA Multi-carrier Cell Extender improves the performance of CDMA Base Stations (BTS) in indoor and outdoor locations, allowing for cost efficient implementation of high capacity radio networks.
PAGE 2
• Connect Cell Extender output Tx/Rx and Rx ports (Bias-T blocks with DIN connectors located on the connectors plate inside of the main cabinet) with Tx/Rx and Rx ports of Main Lines of the proper sector using two DIN-DIN jumpers. AC Connection • 20A Breakers must be installed in the main electrical box (or A-box). • 3-conductor AC-wire gage 12-14 must be run through metal conduit to the electrical junction box inside of the CCI Cell Extender cabinet.
PAGE 3
This equipment complies with Part 24 of the FCC rules. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. In order to comply with FCC rules for RF exposure, it must be observed that the antenna connected to this equipment be fixed on an outdoor structure and that it must have a minimum separation distance of 10 meters between it and any person.
PAGE 4
* Reverse Link Forward Link PCS Operating Range 1850-1910MHz 1930-1990 MHz Nominal 20 dB Bandwidth 60 MHz 39.27 MHz PCS band specific filters AD, BE, FC AD, BE, FC Nominal Pass-Band Gain 12 dB max Adjustable to 13.94 dB max System Noise Figure: 1.5.0 dB Max. System Group Delay: 180 nanosecond Max Pass Band Ripple: +/-0.5 dB Max. Output Third Order IM3 @ 1.98 MHz 0ffset: -55 dBc/30 kHz 1 dB Compression Point: +15 dBm Min. +58.5 dBm Typ. Input /Output VSWR: 1.5:1 Max. 1.5:1 Max.