Installation Guide

ManualsBrandsCommScope Technologies ManualsElectronicsThe OneCell RP5100 LTE Band 66

DRAFT

Hardware Installation Guide

Release 4.5

Document Number: M0303A2

ONECELL

Document Revision: 4.5.03

Date: December 2020

Summary of content (132 pages)

PAGE 1
ONECELL® Hardware Installation Guide Release 4.5 Document Number: M0303A2 Document Revision: 4.5.
PAGE 2
Copyright 2020 CommScope, All rights reserved. THIS DOCUMENT HAS BEEN DEVELOPED BY COMMSCOPE, AND IS INTENDED FOR THE USE OF ITS CUSTOMERS AND CUSTOMER SUPPORT PERSONNEL. THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED.
PAGE 3
Contents Document revision history About this document Audience ....................................................................................................................xiii Purpose.......................................................................................................................xiii What you need to know .............................................................................................xiii Customer documentation .....................................................
PAGE 4
Contents Mounting the Radio Point on the ceiling tile ......................................................4-5 Mounting the Radio Point above the ceiling tile...............................................4-15 Flown mount ............................................................................................................4-22 Flown mount installation...................................................................................4-24 Pole mount ....................................................
PAGE 5
Contents FCC Part 15 ........................................................................................................ A-2 EN55032............................................................................................................. A-2 Human exposure limits for ONECELL deployments ............................................... A-2 Reference documents ......................................................................................... A-5 FCC ID..........................................
PAGE 6
Contents Replacing a pole mounted Indoor RP...............................................................D-66 Replacing a vertical pole mounted Rugged RP................................................D-69 Replacing a horizontal pole mounted Rugged RP............................................D-76 Replacing a wall mounted Rugged RP.............................................................D-81 RP post-replacement verification............................................................................
PAGE 7
Contents DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 8
List of figures Figure 1-1 Figure 1-2 Figure 3-1 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure E-1 Figure E-2 Figure E-3 Figure E-4 Figure E-5 Figure E-6 Figure E-7 ONECELL solution .........................................................................1-3 Baseband Controller ports ...............................................................1-5 Fan label.........................................................
PAGE 9
List of tables Table 1 Table 2 Table 1-1 Table A-1 Table A-2 Table C-1 Table E-1 Customer documentation ................................................................... xiv Conventions ........................................................................................ xv Baseband Controller physical port assignments.................................1-4 RF exposure for ONECELL at maximum power internal antennas for RP5000 series ........................................................................
PAGE 10
DRAFT List of tables x M0303A2 4.5.
PAGE 11
Document revision history The following section lists documentation changes in ONECELL® Installation Guide, v4.5 (M0303A2). Revision 4.5.03 (December 17, 2020) • Removed Draft watermark for TD • Replaced Figure 3-1 on page 3-5 • Added topic, Antenna port label on page 5-4 Revision 4.5.
PAGE 12
DRAFT Document revision history xii M0303A2 4.5.
PAGE 13
About this document This document provides the procedures for installing and configuring the Baseband Controller and Radio Points. Audience This document is written for computer hardware installers and administrators, network architects and business planners who are responsible for the planning and design of the CommScope ONECELL deployment environment. Purpose This guide provides the information necessary for installing the ONECELL hardware in the operator’s network.
PAGE 14
About this document Table 1. Customer documentation Title Contents ONECELL® Feature Guide, v4.5 (M0303A0) Contains a description of anchor features for the current release, and a system overview, including CommScope provided components and required components from other vendors. ONECELL® Network Planning Guide, v4.
PAGE 15
About this document Conventions This guide uses the following text conventions, as applicable. Table 2. Conventions Convention Description Syntax symbols <> Enclose a required parameter or set of parameters. For example: >band-class is a required parameter. [] Enclose an optional parameter or set of parameters. For example: >activate image [reboot] [reboot] is an optional parameter. | Separates items on a list of parameters, only one of which can be used.
PAGE 16
About this document Table 2. Conventions Convention Description Plain italic font Indicates file names, directory paths, book titles, chapter titles, and user accounts. Bold font Indicates text that appears on screen exactly as shown, for example, names of screens, names of buttons, items on menus, and items on pull down lists. blue text Indicates a hypertext link. Other conventions > Indicates graphical user interface (GUI) menu path.
PAGE 17
Part I: Overview and preparation Chapter 1 CommScope ONECELL® overview Chapter 2 Preparing to install the ONECELL system DRAFT
PAGE 18
DRAFT
PAGE 19
Chapter 1 CommScope ONECELL® overview This chapter contains a high level overview of the ONECELL deployment and the ONECELL components installed in the ONECELL system. Overview 1-2 CommScope ONECELL system 1-2 ONECELL hardware components 1-3 DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 20
Chapter 1 CommScope ONECELL® overview Overview ONECELL is a revolutionary wireless system that can deliver the ultimate in wireless performance.
PAGE 21
Chapter 1 CommScope ONECELL® overview Figure 1-1. ONECELL solution ONECELL hardware components The ONECELL hardware consists of the following components: • Baseband Controller — Baseband Controller Chassis — Baseband Controller Module — Power/Fan Unit (PFU) DRAFT Baseband Controller physical ports The following ports are on the front panel of the Baseband Controller Module. Table 1-1 shows the port assignments. In addition, there is a connector used for the GPS antenna cable.
PAGE 22
Chapter 1 CommScope ONECELL® overview Table 1-1. Port Assignment Baseband Controller physical port assignments Network Port Speed Media Type Description MGMT Local Management 1 Gbps RJ45 External Interface to access the WebGUI on the Baseband Controller. 0 Not used 1 Gbps RJ45 Not used 1-6 IQ Data 1 Gbps RJ45 Fronthaul IQ Data Traffic between the Baseband Controller and Radio Points via an Ethernet switch on copper (RJ45) port.
PAGE 23
Chapter 1 CommScope ONECELL® overview Figure 1-2. Baseband Controller ports Copper wire ports Fiber optic ports DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 24
DRAFT Chapter 1 CommScope ONECELL® overview 1-6 M0303A2 4.5.
PAGE 25
Chapter 2 Preparing to install the ONECELL system This section has the steps to complete before starting the ONECELL installation. Overview 2-2 Before installing the ONECELL components 2-2 DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 26
Chapter 2 Preparing to install the ONECELL system Overview This document describes the ONECELL installation and includes: • Chapter 3, Baseband Controller installation • Chapter 4, RP5100i installation • Chapter 5, RP5100r installation • Chapter 6, RP2000 Installation • Chapter 7, RP2100 Installation Before installing the ONECELL components Before installing the ONECELL components, the system integrator must plan the network for the topology that will be deployed.
PAGE 27
Part II: ONECELL component installation Chapter 3 Baseband Controller installation Chapter 4 RP5100i installation Chapter 5 RP5100r installation Chapter 6 RP2000 Installation Chapter 7 RP2100 Installation DRAFT
PAGE 28
DRAFT
PAGE 29
Chapter 3 Baseband Controller installation This chapter contains the Baseband Controller installation procedures, including chassis installation into a rack, Baseband Controller Module and Power/Fan Unit installation into the Baseband Controller Chassis and the cables required for a basic installation. Preparing for Baseband Controller installation 3-2 Installing the Baseband Controller into a rack 3-2 DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 30
Chapter 3 Baseband Controller installation Preparing for Baseband Controller installation Open the shipping box. It should have the components for one complete Baseband Controller Module: • Baseband Controller Chassis – including four mounting screws • Baseband Controller Module • Power/Fan Unit (PFU) The Baseband Controller is 1U high. Be sure there is enough room for the Baseband Controller in the rack.
PAGE 31
Chapter 3 Baseband Controller installation 2 Slide the chassis into the rack. 3 Line up the holes in the chassis ears to the holes in the rack. 4 Secure the chassis with the screws. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 32
Chapter 3 Baseband Controller installation Carefully slide the BC into the front of the chassis. 6 Secure the BC by tightening the front panel screws. DRAFT 5 3-4 M0303A2 4.5.
PAGE 33
Chapter 3 Baseband Controller installation 7 In the back of the rack, carefully slide the PFU into the back of the chassis. CAUTION The PFU has a fan hazard. A label is affixed to the top of the PFU indicating the hazard. Figure 3-1. Fan label NOTE: The connectors on the PFU should fit easily into the connector on the BC. Do not force the PFU into the chassis. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 34
Chapter 3 Baseband Controller installation Secure the PFU by tightening the thumb screws. 9 Connect the power cord to the PFU. DRAFT 8 3-6 M0303A2 4.5.
PAGE 35
Chapter 3 Baseband Controller installation 10 On the Baseband Controller Module’s front panel, connect the GPS antenna cable. 11 Connect the Ethernet or fiber optic cable to the appropriate port. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 36
Chapter 3 Baseband Controller installation 12 On the back of the Baseband Controller, turn on the power. DRAFT The LEDs on the front panel will be solid green, when the power is on. If none are on, check your power connection. If the LED pattern is other than all green, see Baseband Controller LED patterns on page B-2. 3-8 M0303A2 4.5.
PAGE 37
Chapter 4 RP5100i installation This chapter describes installing indoor Radio Points on ceiling tiles, above ceiling tiles, on poles and in a flown configuration. RP5100i installation overview 4-2 Ceiling mount 4-3 Flown mount 4-22 Pole mount 4-31 DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 38
Chapter 4 RP5100i installation RP5100i installation overview The RP5100i is the Radio Point for indoor solutions. There are four configurations for installing the RP5100i, which are dependent on the ceiling type. NOTE Ceiling mount, on tile • Ceiling mount, above tile • Flown mount • Pole mount Once the Radio Point is installed and powered on, it may take up to 20 minutes for the frequency to stabilize and lock. If the MR port is connected to a switch that does not provide IEEE802.
PAGE 39
Chapter 4 RP5100i installation Ceiling mount Mounting the Radio Point (RP) above or on the ceiling tile requires the following hardware provided by CommScope: • Radio Point plate and screws • 4" octagon box, 1-1/2" deep with 1/2" side cutouts • Clamp and screw Figure 4-1. CommScope ceiling mount kit contents Octagon box Mounting plate for octagon box with 2 screws Mounting plate for RP with 4 screws DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 40
Chapter 4 RP5100i installation Mounting the Radio Point (RP) above or on the ceiling tile requires the following hardware provided by the system integrator: • Drop rail – Eaton B-line BA50A or equivalent, with a static load capacity of at least 25 lbs without a drop wire, recommended Figure 4-2. Drop rail, system integrator-provided Drop rail DRAFT Clamp 2 screws 4-4 M0303A2 4.5.
PAGE 41
Chapter 4 RP5100i installation Mounting the Radio Point on the ceiling tile 1 Remove two ceiling tiles from the overhead. 2 Place the octagon box on the tile and trace the outline. Cut the opening. 3 Drill a 1/2-inch diameter hole for the Ethernet cable pass-through. NOTE: Use a 1-1/2 deep RACO 8125 or equivalent. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 42
Chapter 4 RP5100i installation 70 mm (2.7”) 138 mm (5.4”) 4 Attach the octagon box to the ceiling bracket using a clamp and screw. Clamp DRAFT Drop ceiling rail 4-6 Octagon box Screws M0303A2 4.5.
PAGE 43
Chapter 4 RP5100i installation 5 Replace the ceiling tile with the cutouts. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 44
Chapter 4 RP5100i installation Install the drop rail/octagon box assembly over the modified tile. DRAFT 6 4-8 M0303A2 4.5.
PAGE 45
Chapter 4 RP5100i installation 7 Attach the mounting plate onto the octagon box and feed the Ethernet cable through the small hole in the ceiling tile. Ethernet cable Mounting plate DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 46
Chapter 4 RP5100i installation 8 Attach base plate to the Radio Point. NOTE: 9 Apply thread locking compound to screws prior to installation. Mount the Radio Point on the octagon box plate. DRAFT Ethernet cable 4-10 M0303A2 4.5.
PAGE 47
Chapter 4 RP5100i installation 10 Secure Radio Point to the octagon plate. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 48
Chapter 4 RP5100i installation 11 Remove the cover from the RP. The cover is attached to the RP with two lanyards. DRAFT NOTE: 4-12 M0303A2 4.5.
PAGE 49
Chapter 4 RP5100i installation 12 Connect Ethernet cable to the MR port on the Radio Point. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 50
Chapter 4 RP5100i installation 13 Replace plastic cover on the Radio Point. DRAFT 14 Replace the ceiling tile next to the Radio Point. 4-14 M0303A2 4.5.
PAGE 51
Chapter 4 RP5100i installation Mounting the Radio Point above the ceiling tile 1 Remove ceiling tile from the overhead. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 52
Chapter 4 RP5100i installation 2 Attach the octagon box to the bracket. NOTE: CommScope recommends an Eaton B-line – BA50A adjustable bracket. Clamp Drop rail Octagon box DRAFT Screw 4-16 M0303A2 4.5.
PAGE 53
Chapter 4 RP5100i installation 3 Attach the bracket to the mounting plate to the octagon box. 4 Attach plate to the Radio Point. NOTE: Apply thread locking compound to screws prior to installation. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 54
Chapter 4 RP5100i installation Attach the Radio Point to the octagon box mounting plate. DRAFT 5 4-18 M0303A2 4.5.
PAGE 55
Chapter 4 RP5100i installation 6 Install drop rail above the ceiling tile. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 56
Chapter 4 RP5100i installation 7 Remove the cover from the RP. NOTE: Connect the Ethernet cables to the Radio Point MR port. DRAFT 8 The cover is attached to the RP with two lanyards. 4-20 M0303A2 4.5.
PAGE 57
Chapter 4 RP5100i installation 9 Replace the cover on the Radio Point. NOTE: The minimum clearance for cooling is 3 inches. Ceiling tile ONECELL® Hardware Installation, Release 4.
PAGE 58
Chapter 4 RP5100i installation 10 Replace the ceiling tile. Flown mount The Radio Point can be flown mounted on the end of a rod. This configuration is used for building where there are no drop ceilings. DRAFT Mounting the Radio Point (RP) in the flown configuration requires the following hardware provided by CommScope in the mounting kit: 4-22 • Radio Point plate and screws • 4" octagon box, 1-1/2" deep with 1/2" side cutouts NOTE: • Remove the top, middle cutout.
PAGE 59
Chapter 4 RP5100i installation Figure 4-3. CommScope flown mount kit contents Octagon box Mounting plate for octagon box with 2 screws Mounting plate for RP with 4 screws Mounting the Radio Point (RP) in the flown configuration requires the following hardware provided by the system integrator: • Rod, 3/8-inch threaded • Nut • Lock nut, nylon • Flat washers DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 60
Chapter 4 RP5100i installation Flown mount installation 1 Attach the threaded, 3/8-inch rod, cut to the required length, to the ceiling. 2 Install the nut and a flat washer on the rod. 3 Slide the octagon box on the rod and install a flat washer and the nylon lock nut. Be sure the bracket is tight between the nuts and there is enough clearance at the end of the rod to attach the bracket to the Radio Point. DRAFT NOTE: 4-24 M0303A2 4.5.
PAGE 61
Chapter 4 RP5100i installation 4 Attach plate to octagon box. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 62
Chapter 4 RP5100i installation Attach the mounting plate to the Radio Point. DRAFT 5 4-26 M0303A2 4.5.
PAGE 63
Chapter 4 RP5100i installation 6 Attach the Radio Point to the octagon box. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 64
Chapter 4 RP5100i installation 7 Remove the cover from the RP. The cover is attached to the RP with two lanyards. DRAFT NOTE: 4-28 M0303A2 4.5.
PAGE 65
Chapter 4 RP5100i installation 8 Connect the Ethernet cable to the Radio Point MR port. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 66
Chapter 4 RP5100i installation 9 Attach the plastic cover to the Radio Point. DRAFT Installation is complete. 4-30 M0303A2 4.5.
PAGE 67
Chapter 4 RP5100i installation Pole mount The Radio Point can be pole mounted. This configuration is used for building where there are no drop ceilings. Mounting the Radio Point (RP) on a pole requires the following hardware provided by CommScope in the mounting kit: • Mounting bracket • Screws Figure 4-4.
PAGE 68
Chapter 4 RP5100i installation Slide the adjustable clamp through the slots on the Radio Point bracket. 3 Wrap the clamp around the pole and tighten the clamp screw to secure the Radio Point to the pole. DRAFT 2 4-32 M0303A2 4.5.
PAGE 69
Chapter 4 RP5100i installation 4 Remove the cover from the RP. NOTE: The cover is attached to the RP with two lanyards. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 70
Chapter 4 RP5100i installation Connect the Ethernet cable to the Radio Point MR port. DRAFT 5 4-34 M0303A2 4.5.
PAGE 71
Chapter 4 RP5100i installation 6 Replace the plastic cover on the Radio Point. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 72
Chapter 4 RP5100i installation DRAFT Installation is complete. 4-36 M0303A2 4.5.
PAGE 73
Chapter 5 RP5100r installation This chapter describes installing Rugged Radio Points on poles and walls. Rugged Radio Point installation overview 5-2 Pole mount installation 5-4 Wall mount installation 5-10 DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 74
Chapter 5 RP5100r installation Rugged Radio Point installation overview The Rugged Radio Point (RP) ships with the following hardware: • Radio Point • Mounting plate • Mounting bolts (M8 Hex) • RJ45, IP67 connector for CAT 6A cables Figure 5-1. An M8 hex wrench is required to install mounting bolts.
PAGE 75
Chapter 5 RP5100r installation NOTE • RJ45, IP67 connector for CAT 5E • Ethernet surge protector, as required by local code (for example, DTK-MRJPOEX or DTK-MRJPOES) If the MR port is connected to a switch that does not provide IEEE802.3bt, type-4 PoE power, the SR port can be used to provide power with a PoE++ injector. In this case, the installer needs to provide a CAT 5E – MPN 17-10044 connector (https:// www.conec.com/catalog/en/rj45-stecker-set.html) to connect the RJ45 to the SR port.
PAGE 76
Chapter 5 RP5100r installation Figure 5-3. RJ45, IP67 connector assembly Antenna port label In a multi operator deployment, each operator can connect their own antenna for the Bands and slots they intend to use. This feature allows an operator to reserve the Band/Radio module slot on an outdoor RP5100r to be used for or by a Baseband Controller when outdoor RP5100s are deployed in an enterprise with multiple Baseband Controllers (up to 4).
PAGE 77
Chapter 5 RP5100r installation Vertical pole mount Slide the two U bolt clamps onto the pole and secure the RP mounting plate to the clamps with four nuts. DRAFT 1 5-5 M0303A2 4.5.
PAGE 78
Chapter 5 RP5100r installation 2 Insert two screws into the upper holes on opposite sides of the RP. Required orientation is with connectors at the bottom of the RP DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 79
Chapter 5 RP5100r installation 3 Hang the RP to the mounting bracket using the installed screws. CAUTION Ensure that the RP is oriented correctly with all connectors at the bottom of the RP. DRAFT Required orientation with connectors at the bottom of the RP 5-7 M0303A2 4.5.
PAGE 80
Chapter 5 RP5100r installation 4 Align holes at bottom location of bracket. Insert and tighten the bottom screws through the plate hole into both sides of the RP. Be sure that all four screws are tightened. NOTE: The torque requirement for the mounting screws is 20-21 in-lbs. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 81
Chapter 5 RP5100r installation 5 Connect the antenna cables on the bottom of the RP. 6 Connect the Ethernet cable RJ45 end to the bottom of the RP to the MR port. MR port Ethernet DRAFT Antenna cables 5-9 M0303A2 4.5.
PAGE 82
Chapter 5 RP5100r installation Wall mount installation Drill four holes in the wall using the mounting plate to determine the hole locations. Mount the backplate on the wall with four molly screws. DRAFT 1 5-10 M0303A2 4.5.
PAGE 83
Chapter 5 RP5100r installation 2 Insert two screws into the upper holes on opposite sides of the RP as shown in the drawing below. Required orientation is with connectors at the bottom of the RP DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 84
Chapter 5 RP5100r installation 3 Attach the RP to the mounting plate. Required orientation is with connectors at the bottom of the RP 4 Tighten the top screws on the RP and insert and tighten the bottom screws on the RP. The torque requirement for the mounting screws is 20-21 in-lbs. DRAFT NOTE: 5-12 M0303A2 4.5.
PAGE 85
Chapter 5 RP5100r installation 5 Insert and tighten the bottom screws through the plate hole into both sides of the RP. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 86
Chapter 5 RP5100r installation 6 Connect the antenna cables on the bottom of the RP. 7 Connect the Ethernet cable RJ45 end to the bottom of the RP to the MR port. NOTE: Insert the Ethernet surge protection as required by local code (for example, DTK-MRJPOEX or DTK-MRJPOES). MR Ethernet port DRAFT Antenna cables 5-14 M0303A2 4.5.
PAGE 87
Chapter 6 RP2000 Installation This chapter describes installing indoor Radio Points on ceiling tiles, above ceiling tiles, on poles and in a flown configuration. Indoor Radio Point (RP2000) installation overview 6-2 Ceiling mount 6-3 Flown mount 6-17 Pole mount 6-23 DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 88
Chapter 6 RP2000 Installation Indoor Radio Point (RP2000) installation overview There are four configurations for installing the Radio Point, which are dependent on the ceiling type. Ceiling mount, on tile • Ceiling mount, above tile • Flown mount • Pole mount Once the Radio Point is installed and the powered on, it may take up to 20 minutes for the frequency to stabilize and lock. DRAFT NOTE • 6-2 M0303A2 4.5.
PAGE 89
Chapter 6 RP2000 Installation Ceiling mount Mounting the Radio Point (RP) above or on the ceiling tile requires the following hardware provided by CommScope: • Radio Point mounting plate and 4 screws • Octagon box mounting plate and 2 screws • 4" octagon box, 1-1/2" deep with 1/2" side cutouts • Clamp with screw - not required for flown mount option Figure 6-1.
PAGE 90
Chapter 6 RP2000 Installation Mounting the Radio Point (RP) above or on the ceiling tile requires the following hardware provided by the systems integrator: • Drop rail – Eaton B-line BA50 recommended Drop rail, system integrator-provided DRAFT Figure 6-2. 6-4 M0303A2 4.5.
PAGE 91
Chapter 6 RP2000 Installation Mounting the Radio Point on the ceiling tile 1 Remove two ceiling tiles from the overhead. 2 Place the octagon box on the tile and trace the outline. Cut the opening. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 92
Chapter 6 RP2000 Installation 3 Drill a 1/2-inch diameter hole for the Ethernet cable pass-through. NOTE: Use a 1-1/2 deep RACO 8125 or equivalent. 1/2-inch diameter hole Hole for mounting plate 4 Attach the octagon box to the ceiling bracket using a clamp and screw. NOTE: CommScope recommends the Eaton B-line – BA50 bracket. Clamp DRAFT Drop ceiling rail 6-6 Octagon box Screw M0303A2 4.5.
PAGE 93
Chapter 6 RP2000 Installation 5 Replace the ceiling tile with the cutouts. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 94
Chapter 6 RP2000 Installation Install the drop rail assembly over the ceiling tile with the cutouts. DRAFT 6 6-8 M0303A2 4.5.
PAGE 95
Chapter 6 RP2000 Installation 7 Attach the mounting plate onto the octagon box. Ethernet cable Mounting plate 8 Attach base plate to the Radio Point. NOTE: Apply thread locking compound to screws prior to installation. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 96
Chapter 6 RP2000 Installation 9 Mount the Radio Point to the octagon box plate. DRAFT 10 Secure the Radio Point. 6-10 M0303A2 4.5.
PAGE 97
Chapter 6 RP2000 Installation 11 Connect the Ethernet cable to the Radio Point. 12 Replace the second ceiling tile. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 98
Chapter 6 RP2000 Installation DRAFT Installation is complete. 6-12 M0303A2 4.5.
PAGE 99
Chapter 6 RP2000 Installation Mounting the Radio Point above the ceiling tile 1 Remove ceiling tile from the overhead. 2 Attach the octagon box to the bracket. Clamp Drop ceiling rail Screw ONECELL® Hardware Installation, Release 4.
PAGE 100
Chapter 6 RP2000 Installation 3 Attach the mounting plate to the Radio Point. NOTE: Attach the Radio Point to the octagon box. DRAFT 4 Apply thread locking compound to screws prior to installation. 6-14 M0303A2 4.5.
PAGE 101
Chapter 6 RP2000 Installation 5 Install the drop rail assembly to the ceiling tile rail. NOTE: The minimum clearance for cooling is 3 inches. Ceiling tile ONECELL® Hardware Installation, Release 4.
PAGE 102
Chapter 6 RP2000 Installation Connect Ethernet cable to RP. 7 Replace the ceiling tile. DRAFT 6 6-16 M0303A2 4.5.
PAGE 103
Chapter 6 RP2000 Installation Flown mount The Radio Point can be flown mounted on the end of a rod. This configuration is used for buildings where there are no drop ceilings. Mounting the Radio Point (RP) in the flown configuration requires the hardware listed in Indoor Radio Point (RP2000) installation overview on page 6-2 Figure 6-3.
PAGE 104
Chapter 6 RP2000 Installation Flown mount installation Attach the threaded, 3/8-inch rod, cut to the required length, to the ceiling. 2 Install the nut and a flat washer on the rod. 3 Slide the octagon box onto the rod and install a flat washer and the nylon lock nut. DRAFT 1 6-18 M0303A2 4.5.
PAGE 105
Chapter 6 RP2000 Installation 4 Attach the plate with two screws to the octagon box. 5 Attach the CommScope supplied mounting plate to the Radio Point with four screws. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 106
Chapter 6 RP2000 Installation Attach the Radio Point to the octagon box. DRAFT 6 6-20 M0303A2 4.5.
PAGE 107
Chapter 6 RP2000 Installation 7 Secure the Radio Point to the octagon box plate. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 108
Chapter 6 RP2000 Installation 8 Connect the Ethernet cable to the Radio Point. DRAFT Installation is complete. 6-22 M0303A2 4.5.
PAGE 109
Chapter 6 RP2000 Installation Pole mount The Radio Point can be pole mounted. This configuration is used for building where there are no drop ceilings. Mounting the Radio Point (RP) on a pole requires the following hardware provided by CommScope in the mounting kit: • Mounting bracket • 4 screws Figure 6-4.
PAGE 110
Chapter 6 RP2000 Installation Slide the adjustable clamp through the slots on the Radio Point bracket. 3 Wrap the clamp around the pole and tighten the clamp screw to secure the Radio Point to the pole. 4 Connect the Ethernet cable to the Radio Point. DRAFT 2 6-24 M0303A2 4.5.
PAGE 111
Chapter 6 RP2000 Installation Installation is complete. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 112
DRAFT Chapter 6 RP2000 Installation 6-26 M0303A2 4.5.
PAGE 113
Chapter 7 RP2100 Installation This chapter describes installing Rugged Radio Points on poles and walls. Rugged Radio Point (RP2100) installation overview 7-2 Pole mount installation 7-4 Wall mount installation 7-17 DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 114
Chapter 7 RP2100 Installation Rugged Radio Point (RP2100) installation overview The Rugged Radio Point (RP) ships with the following hardware: NOTE • Radio Point • Mounting plate • Mounting brackets • Four tamper-resistant mounting screws (M5) • RJ45, IP67 connector • Two 4.3-10 antenna couplers A tamper-resistant T25 Torx bit, 1/4" hex shank, attached to a driver handle, is required to secure the tamper-resistant mounting screws.
PAGE 115
Chapter 7 RP2100 Installation Mounting the Radio Point (RP) on a wall requires the following hardware provided by the system integrator: • Four molly screws capable – 50 lb (23 kg) minimum rating Before installing the RP on the pole, terminate the RP end of the Ethernet cable with the RJ45, IP67 connector provided in the box. Once the Radio Point is installed and the powered on, it may take up to 20 minutes for the frequency to stabilize and lock. DRAFT NOTE 7-3 M0303A2 4.5.
PAGE 116
Chapter 7 RP2100 Installation Pole mount installation There are two orientations for pole mount installations: NOTE • Vertical pole mount • Horizontal pole mount The minimum pole diameter requirement is 4'' (102mm). Vertical pole mount 1 Attach mounting brackets to mounting plate. NOTE: 2 The torque requirement for the bracket mounting screws is 5-6 in-lbs. Slide the adjustable clamp through the slots on each RP mounting bracket on the RP plate.
PAGE 117
Chapter 7 RP2100 Installation Wrap each clamp around the pole and tighten the clamp screw to secure the RP to the pole. DRAFT 3 7-5 M0303A2 4.5.
PAGE 118
Chapter 7 RP2100 Installation 4 Insert two screws into the upper holes on opposite sides of the RP as shown in the drawing below. CAUTION Ensure that the RP is oriented correctly with the two antenna connectors at the top of the RP. Required orientation DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 119
Chapter 7 RP2100 Installation Hang the RP to the mounting bracket using the installed screws. Align holes at bottom location of bracket. DRAFT 5 7-7 M0303A2 4.5.
PAGE 120
Chapter 7 RP2100 Installation 6 Insert and tighten the bottom screws through the plate hole into both sides of the RP. Be sure that all four screws are tightened. NOTE: The torque requirement for the mounting screws is 20-21 in-lbs. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 121
Chapter 7 RP2100 Installation 7 Connect the antenna couplers on the top of the RP. NOTE: Check the antenna coupler manufacturer’s documentation for torque requirements. Connect the Ethernet cable RJ45 end to the bottom of the RP. DRAFT 8 7-9 M0303A2 4.5.
PAGE 122
Chapter 7 RP2100 Installation Horizontal pole mount 1 Attach mounting brackets to mounting plate. The torque requirement for the bracket mounting screws is 5-6 in-lbs. DRAFT NOTE: 7-10 M0303A2 4.5.
PAGE 123
Chapter 7 RP2100 Installation 2 Slide the adjustable clamp through the slots on each RP mounting bracket on the RP plate. Slide adjustable clamp end through slots DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 124
Chapter 7 RP2100 Installation Wrap each clamp around the pole and tighten the clamp screw to secure the RP to the pole. 4 Insert two screws into the upper holes on opposite sides of the RP as shown in the drawing below. DRAFT 3 7-12 M0303A2 4.5.
PAGE 125
Chapter 7 RP2100 Installation CAUTION Ensure that the RP is oriented correctly with the two antenna connectors at the top of the RP. Required orientation DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 126
Chapter 7 RP2100 Installation Hang the RP to the mounting bracket using the installed screws. Align holes at bottom location of bracket and install two additional screws. DRAFT 5 7-14 M0303A2 4.5.
PAGE 127
Chapter 7 RP2100 Installation 6 Insert and tighten the bottom screws through the plate hole into both sides of the RP. Be sure that all four screws are tightened. NOTE: The torque requirement for the mounting screws is 20-21 in-lbs. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 128
Chapter 7 RP2100 Installation 7 Connect the antenna couplers on the top of the RP. NOTE: Check the antenna coupler manufacturer’s documentation for torque requirements. Connect the Ethernet cable RJ45 end to the bottom of the RP. DRAFT 8 7-16 M0303A2 4.5.
PAGE 129
Chapter 7 RP2100 Installation Wall mount installation 1 Drill four holes in the wall using the mounting plate to determine the hole locations. Mount the backplate on the wall with four molly screws. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 130
Chapter 7 RP2100 Installation 2 Insert two screws into the upper holes on opposite sides of the RP as shown in the drawing below. DRAFT Required orientation 7-18 M0303A2 4.5.
PAGE 131
Chapter 7 RP2100 Installation 3 Attach the RP to the mounting plate. Tighten the top screws on the RP and insert and tighten the bottom screws on the RP. NOTE: The torque requirement for the mounting screws is 20-21 in-lbs. DRAFT ONECELL® Hardware Installation, Release 4.
PAGE 132
Chapter 7 RP2100 Installation 4 Insert and tighten the bottom screws through the plate hole into both sides of the RP. 5 Connect the antenna couplers on the top of the RP. NOTE: Check the antenna coupler manufacturer’s documentation for torque requirements. Connect the Ethernet cable RJ45 end to the bottom of the RP. DRAFT 6 7-20 M0303A2 4.5.