xxxxxxxxxx MB-62490 Full Motion TV Wall Mount (For 42" - 90" TVs Indoor/Outdoor Fits VESA 200/300/400/500/600)
4-10 Before you begin, carefully read and understand the instructions in this manual. Please follow the instructions in the order presented in this manual and observe all warnings and cautions. four (45.36 kgs). 615mm/24.2" 1/4 in. (6 mm) wood drill bit or 1/2 in. (12 mm) masonry drill bit. This mount has been tested to support a television with diagonal screen sizes between 32 in. and 90 in. (81.3 cm & 2.29 m) and a weight up to 100 lbs. (45.36 kgs). 100 lbs. 62mm/2.
Pre-Installation brick Part Description Quantity AA Nylon anchor 4 BB Lag bolt washer 4 CC Lag bolt DD Screw (size M5x14, M6x14, M6x30, M8x30, M8x50) EE Washer FF Spacer (size Φ15xΦ8x5 and Φ15xΦ8x15) 4 4 each 4 8 each A E C F D B Part Description Quantity A Wall mount 1 B Mounting bracket 2 C Thumb screw 2 D Allen key 1 E Wrench 1 F Bubble level 1
Installation 1 2 DD EE FF Screw ts correctly Screw is too Screw is too long short CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer service. Use the shortest screw and spacer combination to accommodate your TV. Using hardware that is too long may damage your TV.
Installation (continued) 3 Mounting brackets to the TV Use the washers (EE) and screws (DD, size M5x14, M6x14) to attach the TV if it has a flat back. Or use the spacers (FF), washers (EE) and screws (DD, size M6x30, M8x30, M8x50) to attach the TV if it has a curved or recessed back. CAUTION: Tighten the screws so the brackets are firmly attached. DO NOT OVERTIGHTEN. This may damage your TV.
Installation (continued) 4 CAUTION: Ensure the wall you select is a weight-bearing wall. Failure to observe this precaution can result in serious physical injury and/or property damage. Consult a professional installer or contact customer service if you have any questions. brick After you have mounted the brackets to the TV, determine the mounting location on the wall. 2/3 Select the best location that you want the PICTURE AREA to be positioned.
Installation (continued) 5 Installing the wall mount (concrete/brick wall) bricks brick. Use the wall mount (A) as a template to mark the installation holes. Use the bubble level (F) to ensure the wall mount (A) is level. Use a 1/2 in. (12 mm) masonry drill bit to slowly drill 3.7 in. (95 mm) pilot holes. Insert anchors (AA) into the holes. Ensure the anchors are completely flush to the concrete surface even if covered by a layer of joint compound or other material.
Installation (continued) 6 Installing the wall mount (wood stud) CAUTION: Avoid potential personal injury or property damage! Drywall covering the wall must not exceed 5/8 in.(16mm) Use a commercially-available stud finder to locate the stud centers in the wall. Studs are usually spaced 16 in. apart. Use the wall mount (A) as a template to mark the installation holes. Use the bubble level (F) to ensure the wall mount (A) is level. Use a 1/4 in. (6 mm) drill bit to slowey drill 3.5 in.
Installation (continued) 7 Attaching the TV Hang the TV on the wall mount and tighten the thumb screws (C) as shown to secure the TV. HEAVY! You will need assistance with this step.
Installation (continued) 8 Managing the cable 9 Adjusting the TV to the desired position Route the cable along the arm. Leveling: Use the wrench (E) to release or tighten the screws on the VESA plate as shown. Assist yourself with the bubble level (F). Tilt: Use the Allen key (D) to release or tighten the knob on the VESA plate as shown.