******** MB-54474 Full Motion Wall Mount for Flat Panel TVs (For up to 47" TVs, Fits VESA 75/100/200)
4-10 Before you begin, carefully read and understand the instructions in this manual. Please follow the instructions in the order presented in this manual and observe all warnings and cautions. two (13.6kgs). 14.33''(364mm) 30 lbs. 2.36''(60mm) 3/16 in. (4.5mm) This mount has been tested to support a television with diagonal screen sizes between 13in. and 47in. (33 cm & 1.19 m) and a weight up to 30 lbs. (13.6kgs).
Pre-Installation masonry, AA Nylon anchor 3 BB Lag bolt washer 3 CC Lag bolt DD Screw (size M4x14,M5x14,M6x14,M8x20) 4 each EE Washer (size M5 and M8) 4 each FF Spacer 3 8 E A F B C D 1 10 20 40 I H J A Wall Mount 1 B VESA plate 1 C VESA extension adapter arm 2 D E F G H I J VESA extension adapter arm Knob Cable clip Allen key Wrench Hexagon Nut Bolt 2 2 1 1 1 8 8 2 30 G 50 3 60 70 4in 80 90 100mm
DD EE FF Screw fits correctly Screw is too long Screw is too short CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer service. Use the shortest screw and spacer combination to accommodate your TV. Using hardware that is too long may damage your TV. However, using a screw that is too short may cause your TV to fall from the mount.
Installation (continued) 3 Installing the VESA extension adapter arms Attach the VESA extension adapter arms (C, D) to the VESA plate (B) using the bolts (J) and Hexagon Nuts (I) as shown. J C B D I D B 4 C Attaching the VESA plate to the TV Using the washers (EE) and screws (DD) to secure the TV of flat back. Using the spacers (FF), washers (EE) and screws (DD) to secure the TV of curved or recessed back. CAUTION: Tighten the screws so the brackets are firmly attached. DO NOT OVERTIGHTEN.
Installation (continued) 5 CAUTION: Ensure the wall you select is a weight-bearing wall. Failure to observe this precaution can result in serious physical injury and/or property damage. Consult a professional installer or contact customer service if you have any questions.
Installation (continued) 6 Installing the wall mount (concrete/masonry wall) masonry blocks masonry block. Use the wall mount (A) as a template to mark the installation holes. Use a level to ensure the wall mount (A) is level. Use a 1/4 in. (6 mm) masonry drill bit to slowly drill 2.4 in. (60 mm) pilot holes. Then use a 3/8 in. (10 mm) masonry drill bit to expand pilot holes. Insert anchors (AA) into the holes.
Installation (continued) BB 8 Installing the decorative cover 9 Attaching the cable clip Attach the cable clip (F) to the wall mount (A) as shown.
Installation (continued) 10 Mounting the TV to the wall mount Connect the wall mount (A) and the VESA plate (B) as shown, and tighten the two knobs (E) to fix the TV. HEAVY! You will need assistance with this step. 11 Managing the cable Route cable along the arm.
Installation (continued) 12 Adjusting the TV to the desired position Tilt: Using the Allen key (G) to release or tighten the screws on the VESA plate as shown. Swivel: Using the wrench (H) to release or tighten the nuts on the VESA plate or using the Allen key (G) to release or tighten the nuts on the arm as shown.