******** MB-53290 Full Motion Wall Mount for Flat Panel TVs (For up to 90" TVs, Fits VESA 200/300/400/600)
4-10 Before you begin, carefully read and understand the instructions in this manual. Please follow the instructions in the order presented in this manual and observe all warnings and cautions. four (50kgs). 615mm/24.21" 1 /4 in. (6 mm) wood drill bit or 1 /2 in. (12 mm) masonry drill bit. This mount has been tested to support a television with diagonal screen sizes between 32in. and 90in. (81.3 cm & 2.29 m) and a weight up to 110lbs. (50kgs). 110 lbs. 62mm/2.
Pre-Installation masonry Part Description Quantity AA Nylon anchor 4 BB Lag bolt washer 4 CC Lag bolt 4 DD Screw (size M5x14,M6x14,M6x30,M8x30,M8x50) EE Washer FF Spacer (size Φ15xΦ8x5 and Φ15xΦ8x15) 4 each 4 8 each A E C F D B 1 10 20 Part Description Quantity A Wall mount 1 B Mounting bracket 2 C Thumb screw 2 D Allen key 1 E Wrench 1 F Bubble level 1 2 30 40 50 3 60 70 4in 80 90 100mm
1 CAUTION: Ensure the wall you select is a weight-bearing wall. Failure to observe this precaution can result in serious physical injury and/or property damage. Consult a professional installer or contact customer service if you have any questions.
Installation (continued) 2 Installing the wall mount (concrete/masonry wall) masonry blocks masonry block. Use the wall mount (A) as a template to mark the installation holes. Use the bubble level (F) to ensure the wall mount (A) is level. Use a 1/2 in. (12 mm) masonry drill bit to slowly drill 3.7 in. (95 mm) pilot holes. Insert anchors (AA) into the holes. Ensure the anchors are completely flush to the concrete surface even if covered by a layer of joint compound or other material.
Installation (continued) 3 Installing the wall mount (wood stud) Use a commercially-available stud finder to locate the stud centers in the wall. Studs are usually spaced 16 in. apart. Use the wall mount (A) as a template to mark the installation holes. Use the bubble level (F) to ensure the wall mount (A) is level. Use a 1/4 in. (6 mm) drill bit to slowey drill 3.5 in. (90 mm) pilot holes. Attach the wall mount (A) to the wall using the lag bolts (CC) and lag bolt washers (BB) as shown.
Installation (continued) 4 5 DD EE FF Screw fits correctly Screw is too Screw is too long short CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer service. Use the shortest screw and spacer combination to accommodate your TV. Using hardware that is too long may damage your TV.
Installation (continued) 6 mounting brackets to the TV Using the washers (EE) and screws (DD, size M5x14,M6x14) to attach the TV of flat back. Or using the spacers (FF), washers (EE) and screws (DD, size M6x30, M8x30, M8x50) to attach the TV of curved or recessed back. CAUTION: Tighten the screws so the brackets are firmly attached. DO NOT OVERTIGHTEN. This may damage your TV.
Installation (continued) 7 Attaching the TV Hang the TV on the wall mount and tighten the thumb screws (C) as shown to secure the TV. HEAVY! You will need assistance with this step.
Installation (continued) 8 Managing the cable 9 Adjusting the TV to the desired position Route cable along the arm. Leveling: Using the wrench (E) to release or tighten the screws on the VESA plate as shown. Assist yourself with the bubble level (F). Tilt: Using the Allen key (D) to release or tighten the knob on the VESA plate as shown.
