UNI FLAME AUTOLIFT MIG/MMA/TIG 165/190/220/250 Inverter Manual 240 Volt Standard MIG / MAG
UNI FLAME AUTOLIFT 2YEARS Warranty * Machine Model . Description MIG/MM/TIG Inverter Part Number KUMJR165 / 190 / 220 / 250 CONTENTS PAGE No: Safety Machine Features Circuit Diagram Panel Structure Main Parameter. Installation & Operation Caution Maintenance Troubleshooting 3 4 5 7 8 10 13 14 14 Machine Model This welding equipment for industrial and professional use conforms to IEC 60974 International Safety Standard.
SAFETY Welding and cutting equipment can be dangerous to both the operator and people in or near the surrounding working area, if the equipment is not correctly operated. Equipment must only be used under the strict and comprehensive observance of all relevant safety regulations. Please read and understand this instruction manual carefully before the installation and use/operation of this equipment. not switch the function modes while the machine is operating.
UNI FLAME AUTOLIFT • • • • • • • • • • • • • MACHINE FEATURES Latest IGBT inverter technology MIG/MAG with gasless wire function MMA (Stick electrode) (DC+ / DC-) function Industrial application High strength metal case construction Internal gear drive wire feeder for 5Kg & 15kg spool Euro style MIG torch connection IP21S rating for environmental / safety protection Stepless voltage and wire feed control Scratch start DC TIG welding Excellent arc stability for MIG / MMA / TIG welding Light weight and port
UNI FLAME AUTOLIFT CIRCUIT DIAGRAM
UNI FLAME AUTOLIFT MAIN PARAMETER 165/190 WELDING CURRENT MIG PRIMARY INPUT VOLTAGE MIG/MMA/TIG Inverter Tecnical Specification Description 10-140 Amps 30-160Amps 240V 1 Phase KUMJR165 Part Number 10-160 Amps 30-190 Amps 240V 1 Phase KUMJR190 Machine Model WELDING CURRENT MMA MIG welding 35% @ 140A / 100% @ 83A 35% @ 160A / 100% @ 95A 35% @ 160A / 100% @ 95A 35% @ 175A / 100% @ 103A duty cycle 40°C MMA welding 0.6 – 0.8mm Stainless Steel 0.9 – 1.0mm Aluminium 0.6 – 0.8mm Ferrous 0.
KUMJR220 240V 1 Phase 30-220 Amps 10-200 Amps MIG/MMA/TIG Inverter Tecnical Specification PRIMARY INPUT VOLTAGE WELDING CURRENT MIG WELDING CURRENT MMA 23 Kgs WEIGHT (Kgs) 0.9 – 1.2mm Flux cored 0.9 – 1.2mm Flux cored 24 Kgs 580 × 230 × 450mm 0.8 – 1.0mm Stainless Steel 0.8 – 1.0mm Stainless Steel 580 × 230 × 450mm 0.9 – 1.2mm Aluminium 0.9 – 1.2mm Aluminium DIMENSIONS (mm) 0.6 – 1.2mm Ferrous 0.6 – 1.2mm Ferrous WIRE SIZE (mm) 15.5-26.5 Volts 15.
UNI FLAME AUTOLIFT INSTALLATION & OPERATION Note: ·Please install the machine strictly according to the following steps. ·The protection class of this machine is IP21S, so avoid using it in rain. 1. Connection of Input Cables Primary input cable is supplied with this welding equipment. Connect the primary input cable with power supply of required input voltage. Refer to data plate on machine for Input voltage, Maximum Input Current (IMAX) and Effective input Current (IEFF). Installation of MMA welding 1.
Installation of gas shielded arc welding (1) Turn the power source on and select the MIG function through the STICK/MIG selector. (See Panel Structure Diagram Number 7) (2) Plug the welding torch into the output socket “10” on the front panel, (See Panel Structure Diagram Number 10) and tighten it. (3) Insert the earth cable plug into the negative socket “8” on the Panel Structure Diagram, and tighten it clockwise.
UNI FLAME AUTOLIFT INSTALLATION & OPERATION Installation of self shielded arc welding (No Gas) (1) Turn the power source on and select the MIG function through the STICK/MIG selector. (See Panel Structure Diagram Number 7) (2) Plug the welding torch into the output socket “10” on the front panel, (See Panel Structure Diagram Number 10) and tighten it. (3) Insert the earth cable plug into the positive socket “9” on the Panel Structure Diagram, and tighten it clockwise.
1. Working Environment. 1.1 1.2 1.3 1.4 The environment in which this welding equipment is installed must be free of grinding dust, corrosive chemicals, flammable gas or materials etc, and at no more than maximum of 80% humidity. When using the machine outdoors protect the machine from direct sun light, rain water and snow etc; the temperature of working environment should be maintained within -10°C to +40°C. Keep this equipment 30cm distant from the wall for ventilation.
UNI FLAME AUTOLIFT MAINTENANCE WARNING: Exposure to extremely dusty, damp, or corrosive air is damaging to the welding machine. In order to prevent any possible failure or fault of this welding equipment, clean the dust at regular intervals with clean and dry compressed air of required pressure.
TROLLEY OPTION MIG 165 / 190 PART NO: UMJRTROLLEY2 TIG TORCH OPTION PART NO: 17V-4MCP25 TROLLEY OPTION MIG 220 / 250 PART NO: UMJRTROLLEY TIG TORCH OPTION PART NO: 26V-4MCP50 UNI FLAME AUTOLIFT MACHINE OPTIONS
%DFN SDQHO VWUXFWXUH ,QSXW SRZHU FDEOH 3RZHU VZLWFK )DQ &ODSERDUG VWUXFWXUH %XUQEDFN WLPH DGMXVWPHQW ´ µ RXWSXW WHUPLQDO ´ µ ´ µ RXWSXW WHUPLQDO ´ µ )DVW 3OXJ 17 :$51,1* %HIRUH 00$ :HOGLQJ 'LVFRQQHFW WKH IDVW SOXJ RQ WKH ZLUH IHHGHU IURP WKH RXWSXW VRFNHW·V ´*$6µ ´12 *$6µ RQ WKH FODSERDUG ,I FDEOH LV QRW GLVFRQQHFWHG ZHOGLQJ YROWDJH LV SUHVHQW FDQ FDXVH DUFLQJ RU Á DVK
PANEL STRUCTURE Front panel structure 1. Power LED 2. Overheating LED 3. Wire inching button 4. Current adjustment knob (in MMA welding) 5. Voltage adjustment knob (MIG/MAG) 6. Wire Feed adjustment knob (MIG/MAG) 7. STICK/MIG selector switch 8. “-” output terminal “1” 9. “+” output terminal “1” 10.
WARRANTY • 2 Years from date of purchase. • Welding Guns of Australia Pty Ltd warranties all goods as specified by the manufacturer of those goods. This Warranty does not cover freight or goods that have been interfered with. All goods in question must be repaired by an authorised repair agent as appointed by this company. Warranty does not cover abuse, mis-use, accident, theft, general wear and tear.
