Comfort Digisystem User manual Comfort Digisystem Receiver DT10 & Programmer DT05 US / English
User manual Table of contents Page 1) Regulatory information 3 2) Introduction Comfort Digisystem 4 3) Overview - Receiver DT10 4 4) Check the hearing instruments input 4 5) Getting started 5 6) Acoustic indication, sound signals 5 7) Modes in the Receiver DT10 6 8) Output for user with different input types and programs in the hearing instrument 6 9) Pairing 8 10) Functions Programmer DT05 - professional tool 9 11) Included accessories 9 12) Menu Programmer DT05 10 13) Battery mai
1) Regulatory information Comfort Digisystem products are not to be used as a substitute to the hearing aids and should be used in accordance with the specifications and recommendations provided by your physician. NOTE! Max output > 130 dB SPL (Sound Pressure Level). Could be very dangerous for your hearing. It is recommended that customers keep the volume control in the lowest position, when turning on the device. If not, the sound could potentially cause harm to the customers’ hearing.
2) Introduction to the Comfort Digisystem Thank you for choosing Comfort Digisystem. Our products are easy to use and give you crystal clear sound. Before using the product, please read this manual carefully. The Comfort Digisystem products feature SecureStream Technology – a unique, patented digital technology allowing eavesdrop-secure radio transfer in real time.
2b. If the hearing instrument is equipped with a DAI input (check with audiologist or hearing instrument manufacturer), no programming of the hearing instrument is necessary. The Receiver DT10 works with the Microphone (M) listening program on your hearing instrument. By setting up the Receiver DT10 with the Programmer DT05, the push-button on the Receiver DT10 can be used to select the listening mode: Radio only (R mode) or Radio + Hearing instrument microphone (R+M mode).
7) Listening modes in the Receiver DT10 The available listening modes in the Receiver DT10 can be setup in different configurations: R Default setting R+M Setup with Programmer DT05 is necessary R and R+M Setup with Programmer DT05 is necessary The Programmer DT05 is used to configure and enable or disable different listening modes in the Receiver DT10. The push-button on the Receiver DT10 is used to toggle between the activated listening modes.
Receiver DT10 with R+M mode enabled and R mode disabled The chart below shows the output (what the user can hear) when Receiver DT10 listening mode R+M is enabled, in combination with different input types and programs in the HI.
9) Pairing The Receiver DT10 can receive but not transmit pairing information. To pair the Receiver DT10 with your Comfort Digisystem transmitter the Receiver DT10 must be connected either to your hearing instrument or to the Programmer DT05. Press the push-button on the Receiver DT10 for 2 seconds to activate pairing mode. When pairing mode is activated, you receive an acoustic indication: • • Send the pairing information within 15 seconds. To interrupt pairing mode, briefly press the push-button.
INFORMATION FOR PROFESSIONALS: 10) Functions Programmer DT05 - optional professional tool Order separately Function indicator Volume button Socket for neckloop Volume button + On / Off Pairing button Menu control Charging socket Socket for headphones / earphones 11) Included accessories • • Volume indicator Headphones Charger A11 Europlug socket Receiver DT10 9
Programmer DT05 The Programmer DT05 is an optional professional tool that can be used both for configuring and test-listening of the DT10. 12) Menu in the Programmer DT05 The Programmer DT05 can also be used to configure all settings at the same time in a DT10. To do this, adjust all parameters in the DT05 and then select Send all on the DT05 menu. The Receiver DT10 must be set to pairing mode. R enable R R+M enable R+M Tone ind.
Pairing When Pairing is selected, the DT10 can be set to pairing mode by pressing the push-button for two seconds. If Pairing isn’t selected, pairing mode cannot be enabled with the push-button. To override this, (if the Receiver DT10 needs to be reconfigured or if new pairing information needs to be received), press and hold the pushbutton on the Receiver DT10 for 2 seconds within 10 seconds of it having been connected to a hearing instrument or a Programmer DT05.
15) Trouble shooting 16) Service and warranty The receiver does not start 1. Check that the correct listening program is selected on the hearing instrument. 2. Make sure the Receiver DT10 is correctly connected to the hearing instrument’s audio shoe. Also check the connection between the audio shoe and the hearing instrument. 3. Make sure all connecting surfaces are clean. 4. Check/replace the hearing instrument’s battery. 5. Remember to press the push-button briefly to switch the DT10 on.
17) Radio range and channels 5) You must not change the battery yourself; please contact your point of purchase. 6) The channel that you use in your country is perhaps not permitted abroad. Always get in touch with your hearing aid provider in your country in order to find out which channels are permitted in different countries. Do not defeat the safety features of the polarized or grounded plug. A polarized plug has two blades with different widths and will only fit into the socket one way.
Comfort Audio AB Comfort Audio AB, Box154, SE-301 05 Halmstad, Sweden Tel. +46 (0)35 260 16 00 Fax +46 (0)35 260 16 50 Local US office: Comfort Audio Inc, 350 South Northwest Hwy, Ste 300 Park Ridge, IL 60068 USA T (847) 656 5450 usa@comfortaudio.com www.comfortaudio.us MA0367 Ver 1.