EN TECHNICAL MANUAL + - B 40-56 Vdc Art 1456B SOLO CON CAVO ROSSO COMELIT 2E7T000500 ONLY WITH COMELIT RED CABLE 2E7T000500 FIXED POE A1 A2 SETTABLE POE A3 Technical manual for Multi Apartment Gateway 1456B N0 POE A4 Passion.Technology.Design.
Warnings • Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the standards in force. • All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any responsibility for improper use of the apparatus, for any alterations made by others for any reason or for the use of non-original accessories or materials.
Configuration of Art.1456B √√ This operation requires a PC loaded with the software ViP Manager version 2.3.0 or later (downloadable from the website www. comelitgroup.com). √√ An active internet connection is also required. 1) Connection Article1456B has 2 network interfaces, A and B, labelled for easy identification, which can be configured separately to meet different system requirements.
2) ViP Manager addressing CASE 1 CASE 2 efault address of the device (192.168.1.200) belonging to the d same router network (e.g.: 192.168.1.1) efault address of the device (192.168.1.200) NOT belonging d to the same router network (e.g.: 192.168.0.1) t. Art.1456B t. Art.1456B INTERFACE A ONLY WITH COMELIT RED CABLE 2E7T000500 ONLY WITH COMELIT RED CABLE 2E7T000500 FIXED POE A1 A2 SETTABLE POE A3 NON POE A4 STATIC IP ADDRESS 192.168.1.
CASE 1 2. Launch the system scan by pressing Scan System [e]. »» all the devices connected to the system will be displayed in the device list. 3. Select device 1456 B [f], select Addressing/ViP address [g], assign an unequivocal ViP address to the device [h] and press Write page [i] to save the current settings.
CASE 2 3. Launch the system scan by pressing Scan System [e] »» the 1456B will appear in the device list [f] 4. In Addressing/ IP address [g] assign device 1456B a Static IP address [h] and a IP netmask [i] compatible with the system for example IP: 192.168.0.5, netmask: 255.255.255.0 (warning: the IP address must not already be in use). 5. Enable "Use default gateway" [l] ONLY for the interface connected to the router (interface A by default) 6. Set the gateway address[m] , for example 192.168.0.
CASE 2 PERFORM A DHCP SYSTEM SCAN AND ASSIGN A VIP ADDRESS Follow the procedure below to perform a system scan in DHCP, to locate all the devices connected to interfaces A and B: • an IP address will be automatically assigned to the devices in addressing mode Autoip (connected to interface B); • an IP address will be automatically assigned to the devices in addressing mode DHCP (connected to interface A), if the system is connected to a server with the DHCP function active; • devices with a static address
3) Licence activation: Activation of the licenses for each apartment allows the users of that residential unit to use the special functions provided by the device 1456B (see page 9 for further information about licenses): • remotely answer an audio/video call from an external unit using a smartphone or tablet (master and slave license); • answer an audio call from a GSM or landline telephone (all licenses); • perform an audio telephone backup of an unreachable device (master and slave license); • the possib
LICENSES AVAILABLE FOR PURCHASE MASTER LICENSE: • Master door entry monitor not required (already integrated in the 1456B) • Up to 15 slaves devices can be added for each apartment, including: • Smartphone / Tablet + Comelit App • PSTN/GSM telephone • Door entry monitor (configured as slave) EXAMPLE APARTMENT WITH MASTER LICENSE: AUDIO TELEPHONE BACKUP VIP * NO APP ACTIVE AND NETWORK DATA AVAILABLE? INTERNET APP GSM YES PSTN SIP PROVIDER * it is possible to add ViP internal units in Slave mode SL
4) DynDNS configuration for remote connection The DynDNS address (Dynamic DNS) allows a DNS name to be permanently associated with the IP address of the same host, even if that address subsequently changes. A DynDNS must be registered in order to make the 1456B accessible from a remote web page and to allow operation of the Comelit ViP remote application. √√ An active internet connection is required to complete the license activation procedure. 1. 2. 3. 4.
5) Port Forwarding setting for remote connection Port forwarding is the operation that allows the transfer of data from one device to another via a specific communication port. This procedure enables an external user (mobile phone) to access a device on a local network (1456B). The procedure for opening router ports for the article 1456B is required in order to allow remote access to the system via a web page (port TCP 8080) and via an App (port TCP 64100*, port UDP 64100*).
6) SIP settings configuration The SIP settings configuration procedure is only to be used when you wish to channel a door entry phone communication to a SIP digital telephone line (PSTN/GSM). It is possible to purchase up to 15 SIP phone lines to be shared between all the apartments. Each phone line is a communication channel: when a call is received from an external unit to landline or mobile phone, the first available SIP line is used.
7) SIP phone lines configuration Access to SIP phone lines is controlled by the username and password supplied by the SIP services provider at the time of purchase. Some providers also provide a User ID (which can be variously designated "User authentication", "user auth" or "user ID". The procedure for phone lines configuration is described below. 1. Select the device 1456B and select Main Settings/SIP phone lines [a]. 2. For each SIP phone line purchased, enter the respective username and password [b]. 3.
8) Apartments configuration In the apartments configuration screen, each apartment can be assigned a license, a ViP address (unequivocal) and a description to allow easy identification of the apartment and the user. √√ An apartment can be enabled for each available license. 1. Select device 1456B and select Main Settings/DynDNS [a]. 2. Configure the individual apartments (max 200) [b]: • Enabling: enable/disable the license for the apartment by selecting Enabled/Disabled.
9) Users configuration (devices) In this page you can configure the slave devices that can be activated for each apartment (max. 15) Each device is identified by its slave number. Each device must be assigned a type (internal unit, app or telephone), a description, the phone number (in the case of a telephone/ mobile phone). 1. Select device 1456B and select Main Settings/Users [a]. 2. Select the apartment for which you wish to configure the users [b] 3.
10) Message server configuration The following procedure describes how to specify on the art. 1456B the IP or ViP address of the art. 1952 device to be used as a message server (if present) 1. Select device 1456B and select Main Settings/Message server [a]. 2. From the pull-down menu [b] select ViP address or IP address and enter the address of the CPS device that is to be used as a message server. 3. Press Write page [c] to save the current settings..
Special configurations App connection settings From the following configuration page you can: • set personalised parameters for the app connection (for example, if you wish to set a different port for connection of the app or if there is a static public address you wish to use for remote connection. • change the maximum number of video connections on the network (max. 16) or on the App (max. 4). 1. Select the device 1456B and select Main Settings/App connection settings [a]. 2.
Connection to the configuration web pages From the web pages you can perform all of the operations available on ViP Manager except license activation. The backup and restore function is only available on the web pages. 1A) Remote connection 1B) Local connection √√ Once the DynDNS configuration has been completed (see page 10) and port 8080 (see page 11) on the router has been opened, remote access of the device will be possible. √√ AN active internet connection is also required. 1A.
Backup and restore The backup function allows you to save the current configuration, which can then be subsequently called up at any time using the restore function. The backup and restore functions are only available from the configuration web pages (to access the web pages, see page 18) 1. As described on page 18: connect to the web pages of the device (in local or remote) and log in. 2. Access the Backup/Restore section by pressing Backup/Restore [a] 3.
Restoring factory settings This procedure allows you to restore all the factory parameter settings and to delete all the device configurations. OFF ON √√ With the dip switches in the default positions (OFF). 1. Switch off the power supply to the device. OFF ON 2. Set all the dip switches to ON. 3. Power on the device. 4. Wait 20 - 40 seconds, until the LEDs start flashing rapidly and alternately (0.1 sec red / 0.1 sec green). OFF ON 5. Return all the dip switches to OFF.
C N 1 C F P 0 S V + C N 1 S S + C N 1 S 0 1 + V OUT IN 1 0 V P A N C F P G C N AL F D P C N 3 - OP OP S + - + C F P P A N AL P A N 6304 0 V 6202W+ 6231 OP OP 0 OUT AL + - V 1 6203W 0 AL OUT 0 V 1 V IN IN 1 2 - 1 2 3 S 0 1 + V OUT IN OUT OUT OUT OUT 4 1 0 V P A N C F P C N 1 C F P 0 S V + C N 1 AL P A N 6501 1 2 1440 + VIP/016G Connection diagram for ViP network + Internet connection network system 6304 0 V 6202W+ 6231 OP OP 0 OUT AL + - V 1 ROUTER 192.
C N 1 C F P 0 S V + C N 1 S S + C N 1 S 0 1 + V OUT IN 1 0 V P A N C F P G C N AL F D P C N 3 - OP OP S + - + C F P P A N AL P A N 6202W+ 6231 OP OP 0 OUT AL + - V 1 6203W 0 AL OUT 0 V 1 V IN IN 1 2 - 1 2 3 S 0 1 + V OUT IN OUT OUT OUT OUT 4 1 0 V P A N C F P C N 1 C F P 0 S V + C N 1 AL P A N 6501 1 2 1440 + VIP/016GS Connection diagram for Single network system 6304 0 V 6304 0 V 6202W+ 6231 OP OP 0 OUT AL + - V 1 ROUTER 192.168.1.1 INTERFACE A IP: 192.
Glossary* • Autoip: Automatic Private IP Addressing (known as APIPA or Auto IP), is a method for automatically assigning IP addresses to the devices connected to the network. • Dynamic DNS: Dynamic DNS is a technology that allows a DNS name to be permanently associated with the IP address of the same host, even if that address subsequently changes.
1st edition 07/2015 code 2G40001422 w w w.comelitgroup.com Passion.Technology.Design.
