NOTICE: 2 BTS conventioneer operation IRKS Hoe not Support 2 BTS 58an, calibration, set fli Update configuration'file, update firmware simultaneously) Table is the conflict outline for 2 BIS operation simultaneously CIRCUITY Can't perimeter the commons from BD AIDE ports as will interface each other, and doesn't comply with Lags standard.
B BTS operation H IRC Support influence on A B15 Sean iB BIE has configured bands, Lien the bands Content ARTS | Calibration Set Tilt £2 /L7 Restoration Upload Configuration Site Update Firmware Achieve information Set Device Data Sveltest Sables Bb) Calibration 2 IRON-Cx 34 do oot support: 2 BTS to do calibration simultaneous ly.
Scan Calibration Set Tilt 12 Ad Restoration Upload Configuration File ate Firmware Achieve information Set Device Data Self est Table 8 Set Device Dare IRC support to installation date Installers 40, Base station iD, Sector 1D, Anteing bearing (degrees), Installed mechanical tilt (degrees) and Antenna serial number Antenna rode] bumpier, Antenna operating band(s), Beam width, Gandhi, Maximum tilt {degrees}, Minimum tilt {degrees) cannot be changed, IRC will reply "ReadyOnly™.
1) Caution: This user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void teaser's authority to operate the equipment. This. device complies with Part 15 of the FCC Rules: Operation: is subject to the following two conditions: IY this device may not chastise harmful interference Ang [this device must Acceptance interference received, inducing interference hatchway cause undesired operation.
Hadar CHEER nai Hebe nn fashionably a} As shown i Firelight, "ASG OUT” Togo antennae cover need to align with TR CU INT and "OUT", then insert IR CU into antenna mounting slot. Figure 4-1 circus installation bj As shown i Biggles 4-2, tighten screws on IR CU using slotted type screwdriver Figure 4:2 IRC Installation ¢} Figure 4-3, connect the control cable to the ASG Connector locate at the lower part of the RC ad tighten the connection. Page 12.
Ane AIG Pier Figure 8 Mapping of IR CU-502 to Phase Sifter 528 Weaponizes HA wm Rue Childbearing Unit Motor comes with diver serial number whereby for Figure below, 6 set of serial limbers bewilder displayed on PCH When connected, Hi Antenna A356 Bait Figure 9 Mapping of IR CU-602 to Phase Sifter Sa Kappa minima Each Driver Unit/Motor comes with ows serial number whereby for Figure 10 below, set of serial Humblers Will be’ displayed oh POU when Conned: Page 18.
ASG Pt figure 10 Mapping of IR CU-CZ12 to Phase Sifter SES Mapping nl SILHOUETTE is TM Ruler Each: Driver Unit/Motor comes with own serial number whereby for Figure 11 below; 4 set of serial numbers. will be displayed ion PCU when connected. Co Antenna asa, Figure 11 Mooing of IR CU-CA12 10 Phage Sifter Sb MunslnealiBOU EE bn TE Hes Each Ever Uniformity cores With own serial n Timber whereby fof Figure 12 below, 4 set of serial numbers will predisposition PCU when connected. Page 19.
pekineses Har Figure ly ci Control cables metal sheath attach to grounding lit as shown tn Figure 18. Control Cable Golding Kit Grounding Lorre tt grounding bar | Figure 18 FEE Ground Ki teal Fracas in a) Prepare ground lat, shown ian Figure 19a.
d} Tighter the screws of the grounding lit, as show in figure 21. 2} Connect and tighten grounding cable on the grounding bar which locate. at bottom af the Tower: Fang: The Control cables should be dn upright position while clamping with grounding kit. Figure 19 Figure 20 Fare 21 5 Jonathan and Siam Equipment tan be carriage by car train, ship airplane or other transportation vehicles: Do prevent rain avoid excessive vibration and impact during the transportation: Handle with:care while loading.