User Manual Code Reader™ 3600 Manual Version 01 Release Date: October 2013 D013597_1.
Statement of Agency Compliance The Code Reader™ 3600 (CR3600) has been tested for compliance with FCC regulations and was found to be compliant with all applicable FCC Rules and Regulations. IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this device must not be co-located or operate in conjunction with any other antenna or transmitter.
Code Reader™ 3600 User Manual Copyright © 2013 Code Corporation. All Rights Reserved. The software described in this manual may only be used in accordance with the terms of its license agreement. No part of this publication may be reproduced in any form or by any means without written permission from Code Corporation. This includes electronic or mechanical means such as photocopying or recording in information storage and retrieval systems. NO WARRANTY. This technical documentation is provided AS-IS.
Table of Contents 1.0 - Unpacking............................................................................................................................................................... 1 2.0 - Charging Station Assembly Instructions................................................................................................................... 1 3.0 - Battery Installation and Removal.....................................................................................................................
1.0 - Unpacking Remove the CR3600 from its packing and inspect it for damage. If the reader was damaged during shipping, please call Code at (801) 495-2200. Based on the kit purchased, a combination of the following components will be included with the CR3600: Charging Station with Embedded CodeXML® Modem Weighted Base Plate Charging Station Screws CodeXML® M3 Modem with USB or RS232 cable Battery USB Cable Power Supply Rubber Feet 2.0 - Charging Station Assembly Instructions 1.
3.0 - Battery Installation and Removal Place the battery into the reader as shown below. Once in place, the battery will snap and lock to indicate proper installation. For battery removal, slide the latch (Figure 8), to unlock and release the battery. Latch Figure 7 Figure 8 4.0 - Charging the CR3600 1. Plug the USB cable into the computer’s USB port (Figure 9) or the power adapter into the wall outlet (Figure 10).
5.0 - Fuel Gauge Battery Status Indicators Check the Battery Life Press the fuel gauge button (Figure 12) to determine remaining battery life. If the battery has less then 10% capacity, the first LED will flash rapidly. For 25% or greater capacity, the LEDs will flash ON for 4 seconds.
.0 - Keypad/Icon Overview Description of Button Function Key Numeric Mode Upper Case Text Mode Lower Case Text Mode Symbol Mode Toggles between numeric characters, upper case text, lower case text, and symbol character input Toggles between numeric characters, upper case text, lower case text, and symbol character input Toggles between numeric characters, upper case text, lower case text, and symbol character input Toggles between numeric characters, upper case text, lower case text, and symbol cha
The chart below shows all of the icons for CodeViewer™ software and their definitions. Icon Description Power Icons 50% to 100% capacity of battery 20% to 50% capacity of battery 0% to 20% capacity of battery – recharge battery as soon as possible Battery is recharging No icon is displayed when battery blank is used with a cabled reader Connection Icon Reader is connected physically or wirelessly to a receiving device (computer, handheld, etc.
9.0 - Communication Mode Switch Charging Stations with an embedded modem feature a Communication Modem Switch. The Communication Mode Switch allows the reader to transmit data through either the modem or wired connection. When the Communication Mode Switch is moved to the right, in the direction of the arrow, the reader will communicate via the modem. The QuickConnect code located on the front of the Charging Station must be scanned to establish a Bluetooth connection.
2. Scan the preferred Batch Mode configuration barcode: Batch Mode Enable - Send and Log Batch Mode Enable - Log Only 3. Scan the preferred Communication Mode settings: USB Keyboard Mode USB Downloader Mode USB Virtual Comm Mode 4. To transmit the captured data to CortexTools™ on your host device, place reader into charging station. The reader will wait 5 seconds before transmitting data. The 5 second delay allows the host device to prepare to receive the data. 12.
14.0 - Establishing a Bluetooth® Connection 1. If establishing a Bluetooth connection using the Charging Station with embedded CodeXML® Modem, slide the Communication Mode Switch on the Charger/Modem Station (Figure 18), to Bluetooth mode (the direction of the arrow). 2. Scan the QuickConnect Code located on the front of the Charging Station with embedded CodeXML® modem or on the external CodeXML® M3 Modem (Figures 19 and 20). 3.
16.
20.0 - Reader ID and Firmware Version To find out the Reader ID and firmware version, open a text editor program (i.e., Notepad, Microsoft Word, etc.
21.0 - CR3600 Dimensions CR3611 CR3612 21.1 - Charging Station Dimensions D013597_1.
22.0 - CR3600 Maintenance The CR3600 needs only minimum maintenance to operate. The tips below for maintenance suggestions. Cleaning the CR3600 The CR3600 window should be clean to allow the best performance of the device. The window is the clear plastic piece inside the head of the reader. Avoid touching the window. Your CR3600 uses CMOS technology that is much like a digital camera. A dirty window may stop the CR3600 from reading barcodes.
23.0 - Warranty Code’s CR3600 carries a standard two year limited warranty as described herein. Charging Stations follow the warranty of the reader. The CR3600 battery carries a one year limited warranty. Customers may purchase either a one or two year CodeOne extended warranty plan. Please contact a Code representative for more information. Limited Warranty Code manufactures its hardware products in accordance with industry-standard practices.